Skip to content
  • On order
Reinforced inlet valves VW SEAT KR 9A ABF Reinforced inlet valves VW SEAT KR 9A ABF

Reinforced inlet valves VW SEAT 1.8 16V KR 2.0 16V 9A ABF

€241.26 (tax incl.)
€301.57 (tax incl.) -20%

Set of 8 reinforced inlet valves for VW and SEAT 1.8 16V KR, 2.0 16V 9A and ABF.

  • Brand: SUPERTECH
  • Engines: KR (1.8 16V), 9A and ABF (2.0 16V)
  • Dimensions: 32 mm, 32.5 mm or 34 mm head, 7 mm stem
  • Material: black nitrided stainless steel, single groove
VWIVN-1034F-8
On order, 15 to 30 days lead time
Pay in installments

VW and SEAT engines covered

The VW 16-valve petrol four-cylinder comes as a 1.8 litre (KR, 133 to 140 hp) and as a 2.0 litre (9A, 136 hp, then ABF, 150 hp). From 1985 to 2000 it powers the Golf II and Golf III GTI 16V, the Jetta II, the Scirocco, the Corrado, the Passat B3 and B4, the Sharan, as well as the Seat Toledo I, Ibiza II and Cordoba.

Each engine has 8 inlet valves, two per cylinder. On the ABF, the original part 051 109 601 B (which supersedes 027 109 601 C) has a 32.0 mm head, a 7.0 mm stem and a 95.5 mm length. Designed for standard power, they are quickly put to the test once tuning raises the lift, the spring rate, the revs or the pressure in the chamber.

SUPERTECH reinforced inlet valves

When the engine revs hard, the inlet valve opens and snaps shut many dozens of times a second to meter the incoming fresh air. Each time it returns, its head strikes the seat machined into the cylinder head, while its stem rubs continuously along the walls of its guide. Its working temperature lies between 400 and 550 °C. Yet the chrome-silicon steel used for the original part is already weakening in this zone: it holds 500 MPa at 500 °C, but only 250 MPa at 600 °C, just above, which is a loss of 50 %. Every gain in lift, spring rate, revs or boost makes the knocks, the rubbing and the heat harder for the valve to withstand.

For these engines, the reinforced valve offered is a SUPERTECH in stainless steel, whose surface receives a black nitride treatment. It hardens the outer layer of the stem and makes it smoother: the stem slides more freely in its guide, wears more slowly and keeps a precise fit for longer, even once tuning has raised the springs and the revs.

Two enlarged sizes join the factory size: the VWIVN-1035-8 takes the head from 32.0 to 32.5 mm, the VWIVN-1038-8 takes it to 34.0 mm, with no change to the stem diameter or the length. With a larger diameter, air crosses the seat through a more generous opening, each cylinder breathes in more and power rises, provided the workshop first recuts the inlet seats to the new diameter.

Inlet valve technical specification

Part numberBrandSizeHead Ø
OEM 32.0 mm
Stem Ø
OEM 7 mm
Length
OEM 95.5 mm
GroovesMaterial
VWIVN-1034-8 SUPERTECH Standard 32.0 mm 7 mm 95.5 mm 1 Black nitrided stainless steel
VWIVN-1034F-8 SUPERTECH Standard 32.0 mm 7 mm 95.5 mm 1 Black nitrided stainless steel
VWIVN-1035-8 SUPERTECH +0.5 mm 32.5 mm 7 mm 95.5 mm 1 Black nitrided stainless steel
VWIVN-1038-8 SUPERTECH +2 mm 34.0 mm 7 mm 95.5 mm 1 Black nitrided stainless steel

The VWIVN-1034-8, VWIVN-1035-8 and VWIVN-1038-8 have a slightly dished head, the VWIVN-1034F-8 a flat head.

Fitting details

PartVW originalReinforced
Collets KPR-VW7-S (single groove)
Valve stem seals 027 109 675 VS-VW7I-8 (inlet)
Valve guide GDE-VW8V-7A

The number of grooves on the valve must match the collets: for its single groove valves, SUPERTECH specifies the KPR-VW7-S collets, which are single groove too.

The +0.5 mm and +2 mm oversizes enlarge the head: they go into a cylinder head whose inlet seats have been cut to the new diameter, workshop work to plan with the cylinder head rebuild.

Technical guide

The brand offered

SUPERTECH Established in California, in San Jose, SUPERTECH has devoted over three decades to valvetrain components for motorsport. Every one of its valves is drawn up for a given engine, checked with ultrasonic, X-ray and laser equipment, then proven by engine tuners in drag racing and on circuits.

How to choose

The groove is the notch that houses the collets keeping the valve under its retainer. Its design governs the way the stem is held, and so the benefit you get.

CriterionOption 1Option 2
Size Standard size
32.0 mm head, meant for a cylinder head whose inlet seats have never been touched and keep their factory diameter. This is the choice for a rebuild true to the original VW design, with no extra machining of the inlet seats.
+0.5 mm or +2 mm oversize
32.5 or 34.0 mm head: the opening at the seat grows, the cylinder draws in more air and power follows, at roughly 10 to 12 cfm for each extra mm of head. The seats are recut to this diameter, ideally with enlarged ports; the oversize also rescues a head whose seats were already reground.
Grooves Single groove
The collets grip the stem over their full height: the groove takes almost nothing and the larger bearing surface lowers friction. The valve then copes with uprated springs, big lift and high revs, whether on track, in drift or in rallying. KPR-VW7-S collets are essential for this design, ideally brand new ones.

When reinforced valves become necessary

  • Sharper camshaft or harder springs
  • Rev limiter pushed back
  • Turbo or supercharger conversion
  • Cylinder head prepared for track, drifting or rallying
  • Damaged, tired or reground standard valves at repair size

Compatible vehicles

ModelEngine codePowerYears
VW Golf II 1.8 GTI 16V KR 136 / 139 hp 1986-1990
VW Jetta II 1.8 16V KR 140 hp 1987-1989
VW Scirocco 1.8 16V KR 139 hp 1985-1989
VW Corrado 1.8 16V KR 136 hp 1989-1992
VW Passat B3 / Variant 1.8 16V KR 136 / 139 hp 1988-1993
VW Corrado 2.0 16V 9A 136 hp 1991-1995
VW Passat B3 / B4 / Variant 2.0 16V 9A 136 hp 1988-1993
VW Passat B4 / Variant 2.0 16V ABF 150 hp 1994-1997
VW Golf III 2.0 GTI 16V ABF 150 hp 1992-1997
VW Sharan 2.0 16V ABF 150 hp 1995-2000
SEAT Toledo I 1.8 16V / 1.8 GT KR 133 / 139 hp 1991-1999
SEAT Toledo I 2.0 16V ABF 150 hp 1993-1999
SEAT Ibiza II 2.0 16V ABF 150 hp 1996-1999
SEAT Cordoba 2.0 16V ABF 150 hp 1996-1999

OEM part number (inlet valve): 051 109 601 B ; 027 109 601 C (ABF)

Important: one set of 8 fills the 8 inlet valves of one engine. The 1.8 16V PL (125 to 129 hp) is not listed for these part numbers and is not covered by this page.

Don't forget the exhaust valves

During a head overhaul, inlet and exhaust valves are normally replaced at the same time. The exhaust valves for these engines are here:

VW Golf 3 GTI 2.0 16V ABF exhaust valves →
VW 1.8 16V KR 2.0 16V 9A exhaust valves →

16 other products in the same category

Viewed products

Loading...