- In stock
Tri-metal crankshaft main bearings VAG 1.8 2.0 TFSI TSI EA888 Gen.2/Gen.3
Set of 10 tri-metal crankshaft main bearing half shells for VAG 1.8 and 2.0 TFSI EA888 engines (Ø 51.96 mm).
- Brands: ACL Race and King Racing
- Fitments: Golf VI and VII, Scirocco, Passat, Audi A3, S3, TT, Seat Leon, Skoda Octavia, Porsche Macan
- Engine codes: CDAA, CHHA, CJXA, CJXB, CJXC, CULA, DNUE and others
- Available sizes: standard to +0.25 mm, increased clearance versions (HX / STDX)
The VAG 1.8 and 2.0 TFSI EA888 engines
The EA888 is a direct-injection turbocharged four-cylinder from the Volkswagen group, built as 1.8 and 2.0 litre units (TFSI, TSI) for Audi, Volkswagen, Seat, Skoda, Cupra and Porsche. All the engines listed below share the same crankshaft journal and housing dimensions: a single bearing set covers the whole family.
The crankshaft of these engines runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series and KING RACING tri-metal sets shown here replace them on built engines.
For these main bearings, the Audi / Volkswagen workshop manual specifies a running clearance of 0.017 to 0.037 mm.
Tri-metal main bearings
In a trimetal bearing, a steel back carries a copper-lead intermediate layer with high load capacity, itself covered by an anti-friction running layer that spares the main journal. The set is supplied complete: 10 half shells, i.e. 5 pairs.
Trimetal targets high, sustained loads, whereas aluminium bi-metal is limited to low to medium loads: about 8,000 psi for the latter, up to 12,000 psi for a performance trimetal, 50% more. The benefit shows in strength and durability on turbo, supercharged and high-revving engines.
Technical specifications
| ACL bearings Crankshaft journal Ø 51.958 / 51.978 mm Housing bore Ø 57.000 / 57.019 mm Width 15.5 mm | King bearings Crankshaft journal Ø 51.956 / 51.976 mm Housing bore Ø 57.000 / 57.020 mm Width 15.5 mm |
| Reference | Brand and treatment | Size | Wall thickness (mm) |
|---|---|---|---|
| 5M5585H-STD | ACL Race - Untreated | Standard | 2.505 |
| 5M5585HX-STD | ACL Race - Untreated | Std, increased clearance (HX) | 2.492 |
| 5M5585H-.025 | ACL Race - Untreated | +0.025 | 2.5175 |
| 5M5585H-.25 | ACL Race - Untreated | +0.25 | 2.63 |
| MB5779XP | King Racing - Untreated | Standard | 2.504 |
| MB5779XP STDX | King Racing - Untreated | Std, increased clearance (STDX) | 2.491 |
| MB5779XP.026 | King Racing - Untreated | +0.026 | 2.517 |
| MB5779XP0.25 | King Racing - Untreated | +0.25 | 2.631 |
Running clearance
Running clearance is the gap between the bearing and the main journal, filled by the oil film.
While the engine turns, the main journal floats on this oil film, which carries the load without direct contact with the bearing. Film thickness depends on clearance: too tight, oil passes poorly, temperature rises and the risk of seizure grows; too wide, oil escapes, the film carries less and oil pressure decreases. A correct clearance ensures both sufficient lubrication and a well-maintained film.
| Size / grade | When to choose it | ACL Race Series | King XP |
|---|---|---|---|
| Standard (STD) | Standard journal, not reground | 0.055 to 0.065 mm | 0.052 mm - 0.065 mm |
| Increased clearance (HX / STDX) | Wider clearance: high oil flow, high rpm | 0.080 to 0.090 mm | 0.077 mm - 0.090 mm |
| +0.025 / +0.026 mm | Polished journal | 0.055 to 0.065 mm | 0.052 mm - 0.065 mm |
| +0.25 mm | Journal reground to 0.25 mm | 0.055 to 0.065 mm | 0.052 mm - 0.065 mm |
Check at assembly: lay a calibrated strip (Plastigauge) on the journal, tighten the main cap following the manufacturer's procedure, then compare the width of the crushed strip with the gauge to read the clearance.

Technical guide
These ACL and King trimetal main bearings are aimed at built engines and racing: where a standard bearing quickly reaches its limit, they accept more power, more rpm and more boost. The range includes the standard size, a +0.025 / +0.026 mm size for a main journal that has only been polished, a +0.25 mm regrind size and the HX / STDX version with increased clearance for high-revving engines or engines needing a high oil flow. It allows the same part number to be kept after the crankshaft is reground and the clearance to be tailored to the oil used and the engine's duty.
The two brands
![]() |
An Australian specialist in high-performance engine bearings since 1949, ACL Bearing Company produces the Race Series: precisely made trimetal bearings, available in numerous sizes and recognised on built engines across the world. |
![]() |
Since the 1960s, Israel's King Engine Bearings has built high-performance engine bearings; its pMax Black trimetal alloy bearings are sized for heavy loads. |
Construction and advantages
| Criterion | ACL Race Series | King Racing |
| Cross-section | ![]() |
![]() |
| Type | High-performance trimetal bearing | High-performance trimetal bearing |
| Country of manufacture | Australia | Israel |
| Construction | Trimetal: steel back, copper layer, soft surface | Trimetal: steel back, copper layer, soft surface |
| Alloy | Race Series (copper-lead) | pMax Black (hardened copper-lead) |
| Protective coating | No | No |
| Available sizes | Standard to +0.25 mm (+ increased clearance HX) | Standard to +0.25 mm (+ increased clearance STDX) |
Vehicle compatibility
This main bearing set fits the VAG 1.8 and 2.0 TFSI EA888 engines sharing the same crankshaft journal and housing dimensions:
| Brand | Model (chassis) | Engine code | Power | Years |
|---|---|---|---|---|
| Audi | A1 (8X1, 8XK) | CWZA | 231 hp | 2014–2018 |
| Audi | A1 Sportback (8XA, 8XF) | CWZA | 231 hp | 2014–2018 |
| Audi | A3 (8P1) | CDAA | 160 hp | 2006–2012 |
| Audi | A3 (8V1, 8VK) | CJXB, CJXC, CJXD, CJXF, CJXG, DJHA, DJHB | 280–310 hp | 2012–2017 |
| Audi | A3 Convertible (8P7) | CDAA | 160 hp | 2008–2013 |
| Audi | A3 Convertible (8V7, 8VE) | CJXC, CJXF, DJHA, DJHB, DNUE | 286–310 hp | 2014–2020 |
| Audi | A3 Limousine (8VS, 8VM) | CHHB, CJXB, CJXC, CJXD, CJXF, CJXG, CYFB, DJHA, DJHB, DJJA, DLRA, DNUE | 220–310 hp | 2013–2020 |
| Audi | A3 Sportback (8PA) | CDAA | 160 hp | 2006–2013 |
| Audi | A3 Sportback (8VA, 8VF) | CHHB, CJXB, CJXC, CJXD, CJXF, CJXG, DJHA, DJHB, DNUE | 220–310 hp | 2012–2020 |
| Audi | A4 Allroad B8 (8KH) | CNCD | 224 hp | 2013–2016 |
| Audi | A4 Allroad B9 (8WH, 8WJ) | CYMC, CYRB, CYRC | 249–252 hp | 2016– |
| Audi | A4 B8 (8K2) | CDHA, CDHB, CNCD | 120–224 hp | 2007–2015 |
| Audi | A4 B8 Avant (8K5) | CDHA, CDHB, CNCD | 120–224 hp | 2007–2015 |
| Audi | A4 B9 (8W2, 8WC) | CYMC, CYRB, CYRC | 249–252 hp | 2015–2019 |
| Audi | A4 B9 Avant (8W5, 8WD) | CYMC, CYRB, CYRC | 249–252 hp | 2015–2019 |
| Audi | A5 (8T3) | CDHB, CNCD, CNCE | 160–230 hp | 2009–2017 |
| Audi | A5 (F53, F5P) | CYMC, CYRB, CYRC | 249–252 hp | 2016– |
| Audi | A5 Convertible (8F7) | CDHB, CNCD, CNCE | 160–230 hp | 2009–2017 |
| Audi | A5 Convertible (F57, F5E) | CYMC, CYRB | 252 hp | 2016– |
| Audi | A5 Sportback (8TA) | CDHB, CNCD, CNCE | 160–230 hp | 2009–2017 |
| Audi | A5 Sportback (F5A, F5F) | CYMC, CYRB, CYRC | 249–252 hp | 2016– |
| Audi | A6 C7 (4G2, 4GC) | CYNB, CYPA, CYPB | 249–252 hp | 2014–2018 |
| Audi | A6 C7 Avant (4G5, 4GD) | CYNB, CYPA, CYPB | 249–252 hp | 2014–2018 |
| Audi | A7 Sportback (4GA, 4GF) | CYNB, CYPA, CYPB | 249–252 hp | 2014–2018 |
| Audi | A8 D4 (4H2, 4H8, 4HC, 4HL) | CYPA | 252 hp | 2016–2018 |
| Audi | Q2 (GAB, GAG) | DNUE | 300 hp | 2018– |
| Audi | Q3 (8UB, 8UG) | CULB, CULC | 180–220 hp | 2014–2018 |
| Audi | Q5 (8RB) | CNCB, CNCD, CNCE | 180–230 hp | 2009–2017 |
| Audi | Q5 (FYB, FYG) | DAXB, DAXC, DAYB, DJYA | 249–252 hp | 2016–2025 |
| Audi | Q5 Sportback (FYT) | DAXB | 367 hp | 2021– |
| Audi | Q7 (4MB, 4MG, 4MQ) | CYMC, CYRB, DMFA | 245–252 hp | 2015– |
| Audi | Q8 (4MN, 4MT) | DMFA | 245 hp | 2019– |
| Audi | TT (8J3) | CDAA | 160 hp | 2008–2014 |
| Audi | TT (FV3, FVP) | CHHC, CJXF, CJXG, CYFB, DKTB, DLRA, DNUF | 230–310 hp | 2014– |
| Audi | TT Roadster (8J9) | CDAA | 160 hp | 2008–2014 |
| Audi | TT Roadster (FV9, FVR) | CHHC, CJXF, CJXG, DKTB, DNUF | 230–310 hp | 2014– |
| Cupra | Ateca (KH7, KHP, KBP) | DNUE | 300 hp | 2018–2026 |
| Porsche | Macan (95B) | CYNB, CYPA | 252 hp | 2015– |
| Seat | Alhambra (710, 711) | CDAA, DEDA | 160–220 hp | 2012–2022 |
| Seat | Altea (5P1) | CDAA | 160 hp | 2007–2015 |
| Seat | Altea XL (5P5, 5P8) | CDAA | 160 hp | 2007–2015 |
| Seat | Exeo (3R2) | CDHA, CDHB | 120–160 hp | 2010–2013 |
| Seat | Exeo ST (3R5) | CDHA, CDHB | 120–160 hp | 2010–2013 |
| Seat | Leon (1P1) | CDAA | 160 hp | 2007–2012 |
| Seat | Leon (5F1) | CJXA, CJXC, CJXE, CJXG, DNUC | 265–310 hp | 2013–2020 |
| Seat | Leon Van/berline à hayon (5F1) | CJXC | 300 hp | 2017–2018 |
| Seat | Leon SC (5F5) | CJXA, CJXC, CJXE | 265–300 hp | 2013–2018 |
| Seat | Leon ST (5F8) | CJXA, CJXC, CJXE, DNUC, DNUE | 265–300 hp | 2013–2020 |
| Seat | Leon ST Van/Estate (5F8) | CJXA, CJXC | 280–300 hp | 2013–2020 |
| Seat | Toledo III (5P2) | CDAA | 160 hp | 2007–2009 |
| Skoda | Octavia II (1Z3) | CDAA, CDAB | 152–160 hp | 2007–2013 |
| Skoda | Octavia II Combi (1Z5) | CDAA, CDAB | 152–160 hp | 2007–2013 |
| Skoda | Octavia III (5E3, NL3, NR3) | CHHA, CHHB, DKTB, DLBA | 220–245 hp | 2013–2020 |
| Skoda | Octavia III Combi (5E5, 5E6) | CHHA, CHHB, DKTB, DLBA | 220–245 hp | 2012–2020 |
| Skoda | Octavia IV (NX3, NN3, PV3) | DLBA | 245 hp | 2020– |
| Skoda | Octavia IV Combi (NX5, PV5) | DLBA | 245 hp | 2020– |
| Skoda | Superb II (3T4) | CDAA, CDAB | 152–160 hp | 2008–2015 |
| Skoda | Superb II Estate (3T5) | CDAA, CDAB | 152–160 hp | 2009–2015 |
| Skoda | Superb III (3V3) | CHHB, CJXA, DNUA | 220–280 hp | 2015–2024 |
| Skoda | Superb III Estate (3V5) | CHHB, CJXA, DNUA | 220–280 hp | 2015–2024 |
| Skoda | Yeti (5L) | CDAA, CDAB | 152–160 hp | 2009–2017 |
| VW | Arteon (3H7, 3H8) | DJHC, DLRB, DNUA | 272–280 hp | 2017–2024 |
| VW | Arteon Shooting Brake (3H9) | DJHC, DNUA | 272–280 hp | 2020–2024 |
| VW | Atlas (CA1, CA2, CA3) | CXDA, DCGA | 220–238 hp | 2017–2023 |
| VW | Atlas Cross Sport (CMC, CMD) | DCGA | 238 hp | 2019– |
| VW | Beetle (5C1, 5C2) | CPKA, CPLA, CPPA, CPRA, CULC | 170–220 hp | 2012–2019 |
| VW | Beetle Convertible (5C7, 5C8) | CPKA, CPLA, CPPA, CPRA, CULC | 170–220 hp | 2012–2019 |
| VW | CC B7 (358) | CDAA, CDAB | 152–160 hp | 2011–2016 |
| VW | Golf VI (5K1) | CDAA | 160 hp | 2009–2011 |
| VW | Golf VI Convertible (517) | CULC | 220 hp | 2013–2016 |
| VW | Golf VII (5G1, BQ1, BE1, BE2) | CHHA, CHHB, CJXB, CJXC, CJXD, CJXE, CJXG, CXCA, CXCB, CXDA, CYFB, DJHA, DJHB, DJJA, DKTB, DLBA, DLRA, DNUC, DNUE | 210–360 hp | 2013–2020 |
| VW | Golf VII Van (5G1, BQ1) | CHHA, CHHB | 220–230 hp | 2013–2017 |
| VW | Golf VII Variant (BA5, BV5) | CJXB, CJXC, CJXD, CJXG, DJHA, DJHB, DNUC, DNUE | 280–360 hp | 2015–2020 |
| VW | Golf VIII (CD1, DA1) | DLBA | 245 hp | 2020– |
| VW | Jetta IV (162, 163, AV3, AV2) | CPKA, CPLA, CPPA, CPRA | 170–211 hp | 2012–2017 |
| VW | Passat Alltrack B7 Variant (365) | CDAA, CDAB | 152–160 hp | 2012–2014 |
| VW | Passat Alltrack B8 Variant (3G5, CB5) | CHHB, CJXA, DNUA | 220–280 hp | 2015–2024 |
| VW | Passat B6 (3C2) | CDAA, CDAB | 152–160 hp | 2007–2010 |
| VW | Passat B6 Variant (3C5) | CDAA, CDAB | 152–160 hp | 2007–2011 |
| VW | Passat B7 (362) | CDAA, CDAB | 152–160 hp | 2010–2014 |
| VW | Passat B7 (A32, A33) | CPKA, CPRA | 170 hp | 2013–2017 |
| VW | Passat B7 Van/Estate (365) | CDAA, CDAB | 152–160 hp | 2010–2014 |
| VW | Passat B7 Variant (365) | CDAA, CDAB | 152–160 hp | 2010–2014 |
| VW | Passat B8 (3G2, CB2) | CHHB, CJXA, CXDA, DNUA, DRFA | 190–280 hp | 2015–2024 |
| VW | Passat B8 Variant (3G5, CB5) | CHHB, CJXA, CXDA, DNUA, DRFA | 190–280 hp | 2014–2024 |
| VW | Passat CC B6 (357) | CDAA, CDAB | 152–160 hp | 2008–2012 |
| VW | Scirocco III (137, 138) | CULA, CULC | 180–220 hp | 2013–2017 |
| VW | Sharan (7N1, 7N2) | CDAA, DEDA | 160–220 hp | 2012–2020 |
| VW | T-roc (A11, D11) | DNUE | 300 hp | 2019– |
| VW | Tiguan (AD1, AX1) | CHHB | 220 hp | 2016–2024 |
| VW | Tiguan Allspace (BW2, BJ2) | CXDA | 220 hp | 2017– |
| VW | Touareg (CR7, RC8) | CYRB, CYRC, DMFA | 245–252 hp | 2018–2023 |
| Vw (Faw) | Golf VII (BN1, BN2, C91) | CHHB | 220 hp | 2015– |
Why replace the bearings
Replacing the bearings during a build or rebuild guards against the most expensive failure: a worn-out main bearing scores the main journal, contaminates the oil circuit with debris and forces at least a crankshaft regrind, or even block repairs. Against such costs a new set weighs little: it is the cheapest part of the crankshaft assembly, but the one whose failure costs the most.
-
Brand
-
Reference5M5585H-STD
-
In stock2 Items



