Skip to content
  • In stock
product product

Reinforced ARP main studs for VAG 1.8 2.0 TFSI EA113 Gen.1/Gen.2 EA888 Gen.1/Gen.2/Gen.3

€184.90 (tax incl.)
€217.52 (tax incl.) -15%

ARP2000 crankshaft main studs for the VAG 2.0 TFSI EA113 and EA888 engines.

  • Brand: ARP
  • Engines: EA113, EA888
  • Thread: M10 x 1.5
  • Grade: ARP2000
ARP-204-5408
1 in stock in France
61 in stock in Europe (72h lead time)
Available in stock in France
Pay in installments

The VAG engines concerned

This kit covers the 2.0 TFSI and TSI engines of the Volkswagen group: the EA113 family (2004 to 2010) and the EA888 family, from the first generation (2008) to generations 3 and 4 (since 2013). They power the Audi A3, S3, A4, TT and TTS, the Volkswagen Golf GTI and R, the Seat Leon Cupra and the Cupra Leon, among others.

The original main cap fastening relies on bolts: this kit replaces them with studs.

Reinforced ARP studs for main bearings

On a crankshaft, the main caps are what hold the shaft against the loads passed on by the connecting rods. If their clamping force drops, the cap shifts slightly on its parting line at every cycle: the mating faces become indented, then the bearing bore goes out of round.

This kit replaces the original main cap bolts with 10 mm ARP2000 studs, with their nuts and washers as the ARP instruction sheet lists them. On EA113 and EA888 blocks, the studs are fitted by hand before the caps go back on; the ARP assembly lubricant supplied with the kit is applied to the threads, nuts and washers, and the nuts are tightened to torque in three passes. Preload is higher and more consistent, and the block threads are preserved. Material: ARP2000, an alloy steel developed by ARP, rated at 220,000 psi tensile strength. Against classes 10.9 and 12.9 of standard fasteners, between 150,800 and 176,900 psi minimum, it offers 24 to 46% more strength. On this four-cylinder engine, the ARP2000 studs in M10 x 1.5 are rated for 1,100 hp at most (calculated estimate).

Technical specifications

Part number Brand Grade / material Nut Thread
ARP-204-5408 ARP ARP2000 Nut M10 x 1.5

Tightening torque

Reference Pass 1 Pass 2 Pass 3
ARP-204-5408 32 Nm 63 Nm 95 Nm

No torque is applied to the stud as it goes into the block: it is screwed in by hand. For a permanent installation, the ARP instruction sheet allows a Loctite thread locker, provided the tightening is completed before the product cures.

The nuts are tightened in the sequence the manufacturer specifies for the main caps; the instruction sheet supplied with the kit describes the full procedure.

Stronger fasteners change the clamping force: the size and roundness of the main bearing bores are checked after installation, and the bores are line-honed if necessary, using the final fasteners and lubricant.

The torque figures above come from the ARP 204-5408 instruction sheet, revision applicable at publication. The official instruction sheet is authoritative in the event of any difference. Read the ARP 204-5408 instruction sheet

Technical guide

All the torque values on this page assume ARP assembly grease; with engine oil they are no longer correct.

Buy the ARP assembly grease →

The ARP brand

ARP Coming from the aerospace industry, Gary Holzapfel founded ARP (Automotive Racing Products) in the early 1970s to put an end to engine failures caused by weak fasteners in motorsport. The company designs and manufactures thousands of part numbers in California, in several material grades depending on the application.

Advantages over the original bolts

Criterion Original main bolts Reinforced ARP studs
Original main bearing cap bolt ARP main stud
Tightening Bolt turned straight into the block Nuts tightened in three passes, steady build-up
Block threads Loaded by the turning bolt at every tightening Stud screwed in by hand, no torque load
Refitting the caps Cap held by hand while the bolts go in Cap guided by the studs

When studs become necessary

  • Power increase from a turbo, supercharger or higher boost
  • Stroker crankshaft or higher rev limit
  • Complete bottom end strip-down
  • Bearing bores or block threads already fatigued
  • Intensive motorsport use

Vehicle compatibility

Model Engine code Power Years
AUDI A1 quattro CDLH 256 hp 2012
AUDI A3 8P CAWB CBFA CCZA 200 hp 2004-2013
AUDI A3 8P AXX BPY BWA 200 hp 2004-2013
AUDI A3 8V CZPB DKZA 190 hp 2016-2020
AUDI A3 8V CNTC 220 hp 2014-2020
AUDI A4 B8 CAEA CDNB CFKA 180 hp 2008-2015
AUDI A4 B8 CAEB CDNC CPMA 211 hp 2008-2015
AUDI A4 B8 CPMB 220 hp 2013-2016
AUDI S1 CWZA 231 hp 2014-2018
AUDI S3 8P BZC CDLC 256 hp 2007-2012
AUDI S3 8P BHZ CDLA 265 hp 2006-2013
AUDI S3 8V CJXB 280 hp 2013-2016
AUDI S3 8V CJXF 286 hp 2014-2016
AUDI S3 8V CJXC DNUE 300 hp 2012-2020
AUDI S3 8V CJXG DJHA 310 hp 2016-2020
AUDI TT 8J BWA 200 hp 2006-2010
AUDI TT 8J CCTA CCZA 200 hp 2008-2010
AUDI TT 8J CESA CETA 211 hp 2010-2014
AUDI TT FV DKZB DNNB 197 hp from 2018
AUDI TT FV CHHC 230 hp from 2014
AUDI TT FV DKTB DNPA 245 hp from 2018
AUDI TTS 8J CDLA CDMA 265 hp 2008-2014
AUDI TTS 8J CDLB 272 hp 2008-2014
AUDI TTS FV CJXF 286 hp from 2015
AUDI TTS FV DNUF 306 hp from 2018
AUDI TTS FV CJXG 310 hp from 2014
AUDI TTS FV DNFD 320 hp from 2020
CUPRA Leon KL CZPB DNNA 190 hp from 2021
CUPRA Leon KL DNPA 245 hp from 2021
KTM X-Bow CAEB 240 hp from 2008
KTM X-Bow GT CDLA 286 hp from 2013
KTM X-Bow GT4 CDLA 360 hp from 2018
KTM X-Bow R CDLA 272 hp from 2010
KTM X-Bow R CDLA 300 hp from 2010
KTM X-Bow RR CDLA 360 hp from 2018
SEAT Leon 1P BWA 200 hp 2005-2009
SEAT Leon 1P CCZB 211 hp 2009-2012
SEAT Leon 1P BWJ CDLD 240 hp 2006-2011
SEAT Leon 1P Cupra R CDLA 265 hp 2009-2012
SEAT Leon 5F DKZA 190 hp 2018-2020
SEAT Leon Cupra 5F CJXE 265 hp 2013-2020
SEAT Leon Cupra 5F CJXA 280 hp 2013-2020
SEAT Leon Cupra 5F CJXH DNUC 290 hp 2015-2020
SEAT Leon Cupra 5F CJXC DNUE 300 hp 2016-2020
SEAT Leon Cupra R 5F CJXG 310 hp 2017-2018
VW Beetle CBFA CCTA CCZA 200 hp 2011-2016
VW Golf 5 GTI AXX BWA 200 hp 2004-2009
VW Golf 5 GTI CAWB 200 hp 2004-2009
VW Golf 5 GTI BYD 230 hp 2006-2008
VW Golf 6 CCZA 200 hp 2009-2013
VW Golf 6 GTI CBFA CCTA 200 hp 2009-2013
VW Golf 6 GTI CCZB 210 hp 2009-2016
VW Golf 6 GTI CDLG 235 hp 2011-2012
VW Golf 6 R CDLC CRZA 256 hp 2009-2013
VW Golf 6 R CDLA 265 hp 2009-2016
VW Golf 7 GTI CNTA CXCA 210 hp 2013-2017
VW Golf 7 GTI CHHB CNTC CXCB CXDA 220 hp 2013-2020
VW Golf 7 GTI CHHA 230 hp 2013-2020
VW Golf 7 GTI DKTB DLBA 245 hp 2017-2020
VW Golf 7 GTI Clubsport CJXE 265 hp 2016-2017
VW Golf 7 GTI Clubsport S CJXG 310 hp 2016-2017
VW Golf 7 GTI TCR CJXH DNUC 290 hp 2018-2020
VW Golf 7 R CJXB 280 hp 2013-2017
VW Golf 7 R CJXD DJHB DNUC 290 hp 2016-2020
VW Golf 7 R CJXC DNUE 300 hp 2013-2020
VW Golf 7 R CJXG DJHA 310 hp 2016-2020
VW Golf 8 GTI DLBA DNPA DRNA 245 hp from 2020
VW Polo R WRC 6R CDLJ 220 hp 2013-2014
VW Scirocco 3 CAWB 200 hp 2008-2009
VW Scirocco 3 CCZB 210 hp 2009-2017
VW Scirocco 3 R CDLC 256 hp 2009-2017
VW Scirocco 3 R CDLA 265 hp 2009-2017
VW Scirocco R CDLK 280 hp 2014-2017

Why is it the most cost-effective solution?

On a tuned 2.0 TFSI, with a larger turbo or an aggressive remap, ARP2000 studs clamp the main caps more firmly than the original bolts and limit the risk of bottom-end damage. Their cost stays low next to the cost of rebuilding a crankshaft and a block.

Consider the crankshaft main bearings

When the bottom end is open, the bearings are replaced too. Here are the tri-metal crankshaft main bearings designed for these engines:

Crankshaft main bearings VAG 2.0 TFSI EA113 →
ACL crankshaft main bearings VAG 2.0 TFSI EA888 Gen2 →
ACL crankshaft main bearings VAG 2.0 TFSI EA888 Gen3 →

  • Brand
    ARP
  • Reference
    ARP-204-5408
  • In stock
    1 Item
  • EAN13
    0672036041335

13 other products in the same category

Viewed products

Loading...