- On order
Reinforced cylinder head gasket VAG 1.8 2.0 TFSI EA113 Gen.1/Gen.2 EA888 Gen.1/Gen.2
Reinforced Athena and Cometic head gasket, as O-Ring or MLS. One gasket per engine.
- Brands: Athena, Cometic
- Engines: 1.8 / 2.0 TFSI EA113 and EA888 Gen.1/Gen.2
- Bores: 82.5 to 84 mm
- Thicknesses: 0.686 to 3.556 mm
- Replaces: 06F 103 383 H, 06H 103 383 AA
The Volkswagen and Audi engines covered
This page covers the VAG 1.8 and 2.0 litre turbocharged petrol four-cylinder engines of the EA113 (Gen.1 and Gen.2) and EA888 (Gen.1 and Gen.2) families, sold as 1.8 TFSI, 2.0 TFSI, TSI, GTI, R, TTS or Cupra. They power, among others, the Audi A1, A3, A4, A5, A6, A8, Q3, Q5 and TT, the Volkswagen Golf, Passat, CC, Tiguan, Scirocco, Jetta, Eos, Beetle, Sharan, Polo, Amarok, Transporter and Multivan, the Seat Leon, Altea, Toledo, Exeo and Alhambra and the Skoda Octavia II, Superb II and Yeti in the table below. One cylinder head covers all four cylinders: the gasket is sold individually, one per engine.
The original gasket carries part number 06F 103 383 H on the EA113 and 06H 103 383 AA on the EA888 Gen.1 and Gen.2. The manufacturer publishes neither its bore, nor its thickness, nor its construction. It is calculated for standard combustion pressure: as the pressure climbs, the clamping load weakens, the head lifts and coolant reaches a cylinder.
Reinforced cylinder head gaskets
The gasket does not guarantee the seal by itself: the fasteners that press the head onto the block weigh as much. A composite gasket settles lastingly beyond 100 N/mm², whereas the 301 stainless steel of the MLS holds 517 N/mm², 5 times more, and regains its shape with every combustion. With the O-Ring, the stainless ring isolates the combustion chamber alone and the gasket body closes the water and oil circuits, with no machining of the block.
This page collects the part numbers of two racing manufacturers, Athena and Cometic, in three constructions: the stainless-ring O-Ring and the multi-layer MLS from Athena, the multi-layer MLS from Cometic. The gasket bores run from 82.5 to 84 mm and the thicknesses run from 0.686 to 3.556 mm, enough to set the compression ratio without touching pistons or head. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.
Technical specifications
| Gasket bore | Thickness | Gasket volume | Gasket type OEM not specified |
Brand | Part number OEM 06F 103 383 H, 06H 103 383 AA |
Engines |
| 82.5 mm | 0.69 mm | 3.69 | MLS | Cometic | C4976-027 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 0.76 mm | 4.06 | MLS | Cometic | C4976-030 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 0.91 mm | 4.86 | MLS | Cometic | C4976-036 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.02 mm | 5.45 | MLS | Cometic | C4976-040 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.14 mm | 6.09 | MLS | Cometic | C4976-045 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.30 mm | 6.95 | MLS | Cometic | C4976-051 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.42 mm | 7.59 | MLS | Cometic | C4976-056 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.52 mm | 8.13 | MLS | Cometic | C4976-060 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.68 mm | 8.98 | MLS | Cometic | C4976-066 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.78 mm | 9.52 | MLS | Cometic | C4976-070 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 1.91 mm | 10.21 | MLS | Cometic | C4976-075 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 2.03 mm | 10.85 | MLS | Cometic | C4976-080 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 2.18 mm | 11.65 | MLS | Cometic | C4976-086 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 2.34 mm | 12.51 | MLS | Cometic | C4976-092 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 2.49 mm | 13.31 | MLS | Cometic | C4976-098 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 3.05 mm | 16.30 | MLS | Cometic | C4976-120 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 82.5 mm | 3.56 mm | 19.03 | MLS | Cometic | C4976-140 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 83.5 mm | 0.69 mm | 3.78 | MLS | Cometic | C4541-027 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 0.76 mm | 4.16 | MLS | Cometic | C4541-030 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 0.91 mm | 4.98 | MLS | Cometic | C4541-036 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.02 mm | 5.59 | MLS | Cometic | C4541-040 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.14 mm | 6.24 | MLS | Cometic | C4541-045 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.27 mm | 6.95 | MLS | Cometic | C4541-050 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.30 mm | 7.12 | MLS | Cometic | C4541-051 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.40 mm | 7.67 | O-Ring | Athena | 330147R | 2.0 TFSI EA113 Gen.1, 1.8 / 2.0 TFSI EA888 Gen.1/Gen.2 |
| 83.5 mm | 1.42 mm | 7.78 | MLS | Cometic | C4541-056 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.52 mm | 8.32 | MLS | Cometic | C4541-060 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.65 mm | 9.04 | MLS | Cometic | C4541-065 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.78 mm | 9.75 | MLS | Cometic | C4541-070 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 1.80 mm | 9.86 | O-Ring | Athena | 330240R | 2.0 TFSI EA113 Gen.1/Gen.2, EA888 Gen.1/Gen.2 |
| 83.5 mm | 1.91 mm | 10.46 | MLS | Cometic | C4541-075 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 2.03 mm | 11.12 | MLS | Cometic | C4541-080 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 2.13 mm | 11.66 | MLS | Cometic | C4541-084 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 2.18 mm | 11.94 | MLS | Cometic | C4541-086 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 2.34 mm | 12.81 | MLS | Cometic | C4541-092 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 2.49 mm | 13.64 | MLS | Cometic | C4541-098 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 3.05 mm | 16.70 | MLS | Cometic | C4541-120 | 2.0 TFSI EA113 Gen.1 |
| 83.5 mm | 3.56 mm | 19.49 | MLS | Cometic | C4541-140 | 2.0 TFSI EA113 Gen.1 |
| 84 mm | 0.69 mm | 3.82 | MLS | Cometic | C4977-027 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 0.76 mm | 4.21 | MLS | Cometic | C4977-030 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 0.76 mm | 4.21 | MLS | Cometic | H2907SP1030S | 2.0 TFSI EA113 Gen.1 |
| 84 mm | 0.85 mm | 4.71 | MLS | Athena | 338486R | 2.0 TFSI EA113 Gen.1/Gen.2, EA888 Gen.1/Gen.2 |
| 84 mm | 0.91 mm | 5.04 | MLS | Cometic | C4977-036 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.02 mm | 5.65 | MLS | Cometic | C4977-040 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.02 mm | 5.65 | MLS | Cometic | H2907SP1040S | 2.0 TFSI EA113 Gen.1 |
| 84 mm | 1.14 mm | 6.32 | MLS | Cometic | C4977-045 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.30 mm | 7.20 | MLS | Cometic | C4977-051 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.30 mm | 7.20 | MLS | Cometic | H2907SP1051S | 2.0 TFSI EA113 Gen.1 |
| 84 mm | 1.42 mm | 7.87 | MLS | Cometic | C4977-056 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.52 mm | 8.42 | MLS | Cometic | C4977-060 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.68 mm | 9.31 | MLS | Cometic | C4977-066 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.78 mm | 9.86 | MLS | Cometic | C4977-070 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 1.91 mm | 10.58 | MLS | Cometic | C4977-075 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 2.03 mm | 11.25 | MLS | Cometic | C4977-080 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 2.18 mm | 12.08 | MLS | Cometic | C4977-086 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 2.34 mm | 12.97 | MLS | Cometic | C4977-092 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 2.49 mm | 13.80 | MLS | Cometic | C4977-098 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 3.05 mm | 16.90 | MLS | Cometic | C4977-120 | 2.0 TFSI EA888 Gen.1/Gen.2 |
| 84 mm | 3.56 mm | 19.73 | MLS | Cometic | C4977-140 | 2.0 TFSI EA888 Gen.1/Gen.2 |
A gasket's volume is the space it leaves free above each cylinder. It is added to the combustion chamber and lowers the compression ratio accordingly. Use this value only to compare gaskets of the same bore.
Preparation and fitting
| Fasteners | Engines | Tightening torque |
| Original cylinder head bolts 06D 103 385 D |
2.0 TFSI EA113 Gen.1/Gen.2, 1.8 / 2.0 TFSI EA888 Gen.1/Gen.2 | not published by the manufacturer |
| ARP cylinder head studs ARP-204-4302 |
2.0 TFSI EA113 Gen.1/Gen.2, 1.8 / 2.0 TFSI EA888 Gen.1/Gen.2 | 36 Nm, then 72 Nm, then 108 Nm |
Before installation, check the flatness of the head and the block with a straight edge, and have either one resurfaced if necessary. Apply no gasket sealant: Athena and Cometic deliver their gaskets already coated.
| Reinforced ARP cylinder head studs 2.0 TFSI EA113 and EA888 Gen.1/Gen.2 → |
Technical guide
The three constructions offered
![]() |
O-Ring / Cut Ring Athena A steel body lined with asbestos-free aramid, with a stainless compression ring crimped around each cylinder. The ring transfers the clamping force to a narrow band, where the seal is made, and a silicone bead closes the water and oil passages. It is the construction most resistant to the high combustion pressures of the range. |
![]() |
Athena MLS A stack of two to five AISI 301 stainless steel sheets, laser cut, stamped and riveted. Around each cylinder, a folded sheet, the Gas Stopper, sends the clamping force back towards the combustion chamber, while raised features keep the water and oil circuits apart. The outer faces are coated: one layer resists heat and fills the small flaws of the block and head, a silicone layer stops the gasket from sticking at removal. It is Athena's all-steel solution, from the prepared naturally aspirated engine to moderate boost; beyond that, the O-Ring stays the construction that takes the highest pressures. |
![]() |
Cometic MLS Stamped stainless steel sheets, stacked and riveted to one another. The outer sheets carry active features around each cylinder and each fluid passage. The seal holds with a measured clamping load and little bore distortion. It is the universal choice, from the prepared naturally aspirated engine to reasonable boost. |
Choosing bore and thickness
Gasket bore. The Athena O-Ring comes in 83.5 mm, the Cometic MLS in 82.5, 83.5 and 84 mm, the Athena MLS in 84 mm.
Thickness. The manufacturer communicates no thickness for the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.
| Your goal | Thickness to choose |
| Keep the original compression ratio | Original thickness not published: measure the removed gasket and take, between 0.686 and 3.556 mm, the figure that comes closest |
| Skimmed cylinder head, make up the lost height | Between 0.686 and 3.556 mm, keep the thickness of the removed gasket and add the material taken off when resurfacing |
| Forced induction build, lower the ratio | 3.556 mm, if the removed gasket is thinner |
| Naturally aspirated build, raise the ratio | 0.686 mm, if the removed gasket is thicker |
With no original thickness published, measure with a dial gauge how far the pistons stand out of the block's gasket face: that figure gives the clearance left between piston and head, especially with the thinnest thickness.
The two brands
| Athena S.p.A., an Italian gasket and engine parts company, has its head office and main plant in Alonte, in the Veneto, and further sites in Spain, the United States, Brazil and India. Car makers fit its multi-layer gaskets as original equipment, and the competition range is entirely drawn and built in Italy. | |
| Cometic Gasket, Inc., an American maker of engine gaskets and sealing solutions, came into being in 1989 in Concord, Ohio. Its trade: the gasket made to order, at the bore and thickness wanted, wholly built in the United States from American materials. |
Advantages over the original gasket
| Criterion | Original gaskets 06F 103 383 H, 06H 103 383 AA | Reinforced gaskets |
| Construction | Not specified by the manufacturer | Multi-layer stainless steel, or steel and aramid fibre with a stainless ring |
| Gasket bore | not published by the manufacturer | 82.5 to 84 mm |
| Thicknesses available | not published by the manufacturer | 0.686 to 3.556 mm, 23 values |
| Compression ratio adjustment | None | Through the thickness chosen |
| Resistance to overpressure | Limited to standard output | Designed for forced induction |
When a reinforced gasket becomes necessary
- Adding forced induction, or raising boost on an already turbocharged engine
- Cylinder rebored beyond what the bore of the gaskets offered (82.5 to 84 mm) covers
- Looking for a compression ratio different from standard, higher or lower
- Engine that has already lost its gasket, or is consuming coolant
- Competition use, where the gasket goes through repeated temperature rises
Vehicle compatibility
| Brand | Model | Engine code | Power | Years |
| AUDI | A1 (8X1, 8XK) | CDLH | 256 hp | 2012 |
| AUDI | A3 (8P1, 8P7, 8PA) | AXX, BHZ, BPY, BWA, BYT, BZB, BZC, CAWB, CBFA, CCTA, CCZA, CDAA, CDLA, CDLC | 160 - 265 hp | 2004 - 2013 |
| AUDI | A4 B7 (8EC, 8ED, 8HE) | BGB, BPG, BPJ, BUL, BWE, BWT, BYK | 170 - 220 hp | 2004 - 2009 |
| AUDI | A4 B8 (8KH, 8K2, 8K5) | CABA, CABB, CAEA, CAEB, CAED, CDHA, CDHB, CDNB, CDNC, CFKA, CPMA, CPMB | 120 - 220 hp | 2007 - 2016 |
| AUDI | A5 (8T3, 8TA) | CABD, CAEB, CAED, CDHB, CDNB, CDNC, CPMA, CPMB | 160 - 220 hp | 2007 - 2017 |
| AUDI | A5 Décapotable (8F7) | CAEA, CAEB, CAED, CDHB, CDNB, CDNC, CPMA, CPMB | 160 - 220 hp | 2009 - 2017 |
| AUDI | A6 C6 (4F2, 4F5) | BPJ, BYK | 170 hp | 2005 - 2011 |
| AUDI | A6 C7 (4G2, 4GC, 4G5, 4GD) | CAEB, CAED, CDNB, CHJA | 180 - 245 hp | 2011 - 2018 |
| AUDI | A8 D4 (4H2, 4H8, 4HC, 4HL) | CHJA | 245 hp | 2012 - 2015 |
| AUDI | Q3 (8UB, 8UG) | CCTA, CCZC, CPSA | 170 - 211 hp | 2011 - 2018 |
| AUDI | Q5 (8RB) | CAEB, CDNB, CDNC, CHJA, CPMA, CPMB | 180 - 245 hp | 2008 - 2017 |
| AUDI | TT (8J3, 8J9) | BPY, BWA, CCTA, CCZA, CDAA, CDLA, CDLB, CDMA, CESA, CETA | 160 - 272 hp | 2006 - 2015 |
| SEAT | Alhambra (710, 711) | CCZA, CDAA | 160 - 200 hp | 2010 - 2015 |
| SEAT | Altea (5P1, 5P5, 5P8) | BWA, BYT, BZB, CCZB, CDAA | 160 - 211 hp | 2006 - 2015 |
| SEAT | Exeo (3R2, 3R5) | BWE, CDHA, CDHB, CDND | 120 - 211 hp | 2009 - 2013 |
| SEAT | Leon (1P1) | BWA, BWJ, BZB, CCZB, CDAA, CDLA, CDLD | 160 - 265 hp | 2005 - 2012 |
| SEAT | Toledo III (5P2) | BWA, BYT, BZB, CDAA | 160 - 200 hp | 2005 - 2009 |
| SKODA | Octavia II (1Z3, 1Z5) | BWA, BZB, CCZA, CDAA, CDAB | 152 - 200 hp | 2005 - 2013 |
| SKODA | Superb II (3T4, 3T5) | BZB, CCZA, CDAA, CDAB | 152 - 200 hp | 2008 - 2015 |
| SKODA | Yeti (5L) | CDAA, CDAB | 152 - 160 hp | 2009 - 2017 |
| VOLKSWAGEN | Amarok (2HA, 2HB, S1B, S6B, S7A, S7B, AGD) | CFPA | 160 hp | 2010 - 2016 |
| VOLKSWAGEN | Amarok Camion plate-forme/Châssis (S1B, S6B, S7B) | CFPA | 160 hp | 2011 - 2016 |
| VOLKSWAGEN | Beetle (5C1, 5C2, 5C7, 5C8) | CBFA, CCTA, CCZA | 200 - 213 hp | 2011 - 2016 |
| VOLKSWAGEN | California T5 Camper (7EC, 7EF, 7EG, 7HF, 7HC) | CJKA, CJKB | 150 - 204 hp | 2011 - 2015 |
| VOLKSWAGEN | California T6 Camper (SGC, SGG, SHC) | CJKA, CJKB | 150 - 204 hp | 2015 - 2019 |
| VOLKSWAGEN | CC B7 (358) | CBFA, CCTA, CCZB, CDAA, CDAB | 152 - 210 hp | 2011 - 2016 |
| VOLKSWAGEN | Eos (1F7, 1F8) | BPY, BWA, CAWB, CBFA, CCTA, CCZA, CCZB | 200 - 210 hp | 2006 - 2015 |
| VOLKSWAGEN | Golf V (1K1, 1K5) | AXX, BPY, BWA, BYD, CAWB, CBFA, CCTA | 200 - 230 hp | 2004 - 2009 |
| VOLKSWAGEN | Golf VI (5K1, 517, AJ5) | CBFA, CCTA, CCZA, CCZB, CDAA, CDLA, CDLC, CDLF, CDLG, CRZA | 160 - 270 hp | 2009 - 2016 |
| VOLKSWAGEN | Jetta III (1K2) | AXX, BPY, BWA, CAWA, CAWB, CBFA, CCTA | 170 - 200 hp | 2005 - 2010 |
| VOLKSWAGEN | Jetta IV (162, 163, AV3, AV2) | CBFA, CCTA, CCZA | 200 hp | 2010 - 2014 |
| VOLKSWAGEN | Multivan T5 (7HM, 7HN, 7HF, 7EF, 7EM, 7EN) | CJKA, CJKB | 150 - 204 hp | 2011 - 2015 |
| VOLKSWAGEN | Multivan T6 (SGF, SGM, SGN, SHM, SHN) | CJKA, CJKB | 150 - 204 hp | 2015 - 2019 |
| VOLKSWAGEN | Passat B6 (3C2, 3C5) | AXX, BPY, BWA, BZB, CAWB, CBFA, CCTA, CCTB, CCZA, CDAA, CDAB, CGYA | 152 - 200 hp | 2005 - 2011 |
| VOLKSWAGEN | Passat B7 (365, 362) | CCZB, CDAA, CDAB | 152 - 210 hp | 2010 - 2015 |
| VOLKSWAGEN | Passat CC B6 (357) | BZB, CAWB, CBFA, CCTA, CCZA, CCZB, CDAA, CDAB, CGYA | 152 - 211 hp | 2008 - 2012 |
| VOLKSWAGEN | Polo V (6R1, 6C1) | CDLJ | 220 hp | 2013 - 2014 |
| VOLKSWAGEN | Scirocco III (137, 138) | CAWB, CCZB, CDLA, CDLC, CDLK | 200 - 280 hp | 2008 - 2017 |
| VOLKSWAGEN | Sharan (7N1, 7N2) | CCZA, CDAA | 160 - 200 hp | 2010 - 2015 |
| VOLKSWAGEN | Tiguan (5N_) | CAWA, CAWB, CCTA, CCTB, CCZA, CCZB, CCZC, CCZD | 170 - 211 hp | 2007 - 2018 |
| VOLKSWAGEN | Transporter T5 (7HB, 7HJ, 7EB, 7EJ, 7HA, 7HH, 7EA, 7EH) | CJKA, CJKB | 150 - 204 hp | 2011 - 2015 |
| VOLKSWAGEN | Transporter T6 Fourgon (SGA, SGH, SHA, SHH) | CJKA, CJKB | 150 - 204 hp | 2015 - 2019 |
OEM part number: 06F 103 383 H (EA113), 06H 103 383 AA (EA888 Gen.1 and Gen.2).
Important: not every part number covers every engine in the survey below: the Engines column of the specifications table shows, for each one, the generations it covers. The 1.8 TFSI EA888 engines only take the Athena O-Ring 330147R. For any other vehicle, check the engine code first before ordering.
Why switch to a reinforced gasket?
When the original gasket is at the end of its possibilities, the reinforced gasket replaces it: under stronger combustion pressure it keeps its shape instead of sagging.
Once an engine is fully tuned, boosted harder or compressed more, the head gasket is the first link of the top end to fail. Choosing a reinforced gasket means avoiding the leak and the head removal that follows, a job considerably dearer than the part.
-
Brand
-
Reference338486R


