- In stock
Reinforced ARP cylinder head studs VAG 1.8 2.0 TFSI EA113 Gen.1/Gen.2 EA888 Gen.1/Gen.2/Gen.3
Kit of 10 ARP cylinder head studs for Volkswagen Group 2.0 TFSI and TSI EA113 and EA888 engines.
- Brand: ARP
- Engines: EA113, EA888
- Thread: M10 x 1.5
- Grade: ARP2000
The engines concerned
The Volkswagen Group 2.0 TFSI and TSI engines, EA113 then EA888 (generations 1 to 4), are 2.0-litre turbocharged inline four-cylinders with an original bore of 82.5 mm: the EA113 was built from 2004 to 2010, the EA888 from 2008 onwards. They power the Audi A3, S3, A4, TT, TTS and S1, the Volkswagen Golf GTI and R, Scirocco and Polo R WRC, the Seat Leon Cupra, the Cupra Leon and the KTM X-Bow, among others. ARP offers the 204-4302 stud kit for them, in ARP2000, and also lists it for the 1.8 TSI EA888.
As standard, the cylinder head is held by ten single-use main bolts: the EA113 and first and second generation EA888 engines use bolt set 06D 103 385 D, the third and fourth generation EA888 engines use set WHT 005 305 (ten M10 x 1.5 bolts, 115 mm long, Ribe head).
Reinforced ARP cylinder head studs
Every combustion cycle pushes the cylinder head upwards. The head fasteners resist it by keeping a constant clamping pressure on the gasket; if that pressure drops, the seal is no longer guaranteed.
The ARP 204-4302 kit contains 10 studs supplied with their washers and 12-point nuts, with an M10 x 1.5 thread, in ARP2000. According to the instruction sheet, each stud is first run into the block by hand, before the cylinder head goes on; the washers and nuts, lubricated, then follow and are tightened in three equal passes following the sequence set by the manufacturer. Developed by ARP, ARP2000 alloy steel is heat treated to 220,000 psi tensile strength, and its threads are rolled once the treatment is done. Compared with the 10.9 and 12.9 classes of standard fasteners, between 150,800 and 176,900 psi minimum tensile strength, the gap reaches 24 to 46 %. In M10 x 1.5, the ARP2000 studs hold up to 600 hp on this four-cylinder engine (calculated estimate).
Technical specifications
| Part number | Brand | Grade / material | Nuts | Thread |
| ARP-204-4302 | ARP | ARP2000 | 12-point | M10 x 1.5 |
Tightening torque
| Part number | Stage 1 | Stage 2 | Stage 3 |
| ARP-204-4302 | 36 Nm | 72 Nm | 108 Nm |
The studs are screwed into the block by hand, without torque. Their instruction sheet allows thread locker if they are to be fixed permanently, on the sole condition that tightening is finished before it sets.
The instruction sheet asks you to clean the block threads and, if needed, to run the ARP 912-0003 tap (M10 x 1.5) through them.
ARP thread sealer goes only on a stud whose hole breaks into the water jacket.
Final tightening is done in three successive stages, following the manufacturer's tightening sequence; these torque figures only hold with ARP assembly lubricant on the threads and under the nuts.
The instruction sheet also calls for ARP lubricant on the washers.
Values taken from ARP instruction sheet 204-4302, in the revision current on the date of publication. In the event of any discrepancy, the official instruction sheet prevails; it also details the full procedure and the tightening sequence. Read the ARP 204-4302 instruction sheet
Technical guide
The stated tightening torques only make sense with ARP assembly grease, applied to the threads and under the nuts.
| Buy the ARP assembly grease → |
The ARP brand
| ARP (Automotive Racing Products) was born in the early 1970s from the initiative of Gary Holzapfel, an engineer from the aerospace industry, determined to eliminate engine failures caused by weak fasteners in motorsport. The company designs and manufactures thousands of parts in California, in several material grades suited to each use. |
Advantages over the original bolts
| Criterion | Original head bolts | Reinforced ARP studs |
![]() |
![]() |
|
| Block thread | Stressed at every tightening | Spared (studs screwed in by hand) |
When studs become necessary
The original fasteners are sized for the engine as it leaves the factory. They need to be reinforced when:
- EA113 and EA888: power raised on a 2.0 TFSI or TSI (engine map, turbo, boost pressure)
- The compression ratio rises as the build progresses
- The original gasket is replaced by a reinforced MLS gasket, which requires a high and uniform preload
- The engine has already suffered a lifted head or a gasket leak
- Competition use imposes severe heat cycles and regular head removals
Vehicle compatibility
| Model | Engine code | Power | Years |
| Audi A1 Quattro | CDLH | 256 hp | 2012 |
| Audi A3 8P | AXX, BPY, BWA, CAWB, CBFA, CCZA | 200 hp | 2004-2013 |
| Audi A3 8V | CZPB, DKZA | 190 hp | 2016-2020 |
| Audi A3 8V | CNTC | 220 hp | 2014-2020 |
| Audi A4 B8 | CAEA, CDNB, CFKA | 180 hp | 2008-2015 |
| Audi A4 B8 | CAEB, CDNC, CPMA | 211 hp | 2008-2015 |
| Audi A4 B8 | CPMB | 220 hp | 2013-2016 |
| Audi S1 | CWZA | 231 hp | 2014-2018 |
| Audi S3 8P | BZC, CDLC | 256 hp | 2007-2012 |
| Audi S3 8P | BHZ, CDLA | 265 hp | 2006-2013 |
| Audi S3 8V | CJXB | 280 hp | 2013-2016 |
| Audi S3 8V | CJXF | 286 hp | 2014-2016 |
| Audi S3 8V | CJXC, DNUE | 300 hp | 2012-2020 |
| Audi S3 8V | CJXG, DJHA | 310 hp | 2016-2020 |
| Audi TT 8J | BWA, CCTA, CCZA | 200 hp | 2006-2010 |
| Audi TT 8J | CESA, CETA | 211 hp | 2010-2014 |
| Audi TT FV | DKZB, DNNB | 197 hp | from 2018 |
| Audi TT FV | CHHC | 230 hp | from 2014 |
| Audi TT FV | DKTB, DNPA | 245 hp | from 2018 |
| Audi TTS 8J | CDLA, CDMA | 265 hp | 2008-2014 |
| Audi TTS 8J | CDLB | 272 hp | 2008-2014 |
| Audi TTS FV | CJXF | 286 hp | from 2015 |
| Audi TTS FV | DNUF | 306 hp | from 2018 |
| Audi TTS FV | CJXG | 310 hp | from 2014 |
| Audi TTS FV | DNFD | 320 hp | from 2020 |
| Cupra Leon KL | CZPB, DNNA | 190 hp | from 2021 |
| Cupra Leon KL | DNPA | 245 hp | from 2021 |
| KTM X-Bow | CAEB | 240 hp | from 2008 |
| KTM X-Bow GT | CDLA | 286 hp | from 2013 |
| KTM X-Bow GT4 | CDLA | 360 hp | from 2018 |
| KTM X-Bow R | CDLA | 272 hp | from 2010 |
| KTM X-Bow R | CDLA | 300 hp | from 2010 |
| KTM X-Bow RR | CDLA | 360 hp | from 2018 |
| Seat Leon 1P | BWA | 200 hp | 2005-2009 |
| Seat Leon 1P | CCZB | 211 hp | 2009-2012 |
| Seat Leon 1P | BWJ, CDLD | 240 hp | 2006-2011 |
| Seat Leon 1P Cupra R | CDLA | 265 hp | 2009-2012 |
| Seat Leon 5F | DKZA | 190 hp | 2018-2020 |
| Seat Leon Cupra 5F | CJXE | 265 hp | 2013-2020 |
| Seat Leon Cupra 5F | CJXA | 280 hp | 2013-2020 |
| Seat Leon Cupra 5F | CJXH, DNUC | 290 hp | 2015-2020 |
| Seat Leon Cupra 5F | CJXC, DNUE | 300 hp | 2016-2020 |
| Seat Leon Cupra R 5F | CJXG | 310 hp | 2017-2018 |
| Volkswagen Beetle | CBFA, CCTA, CCZA | 200 hp | 2011-2016 |
| Volkswagen Golf 5 GTI | AXX, BWA, CAWB | 200 hp | 2004-2009 |
| Volkswagen Golf 5 GTI | BYD | 230 hp | 2006-2008 |
| Volkswagen Golf 6 | CCZA | 200 hp | 2009-2013 |
| Volkswagen Golf 6 GTI | CBFA, CCTA | 200 hp | 2009-2013 |
| Volkswagen Golf 6 GTI | CCZB | 210 hp | 2009-2016 |
| Volkswagen Golf 6 GTI | CDLG | 235 hp | 2011-2012 |
| Volkswagen Golf 6 R | CDLC, CRZA | 256 hp | 2009-2013 |
| Volkswagen Golf 6 R | CDLA | 265 hp | 2009-2016 |
| Volkswagen Golf 6 R | CDLF | 270 hp | 2009-2012 |
| Volkswagen Golf 7 GTI | CNTA, CXCA | 210 hp | 2013-2017 |
| Volkswagen Golf 7 GTI | CHHB, CNTC, CXCB, CXDA | 220 hp | 2013-2020 |
| Volkswagen Golf 7 GTI | CHHA | 230 hp | 2013-2020 |
| Volkswagen Golf 7 GTI | DKTB, DLBA | 245 hp | 2017-2020 |
| Volkswagen Golf 7 GTI Clubsport | CJXE | 265 hp | 2016-2017 |
| Volkswagen Golf 7 GTI Clubsport S | CJXG | 310 hp | 2016-2017 |
| Volkswagen Golf 7 GTI TCR | CJXH, DNUC | 290 hp | 2018-2020 |
| Volkswagen Golf 7 R | CJXB | 280 hp | 2013-2017 |
| Volkswagen Golf 7 R | CJXD, DJHB, DNUC | 290 hp | 2016-2020 |
| Volkswagen Golf 7 R | CJXC, DNUE | 300 hp | 2013-2020 |
| Volkswagen Golf 7 R | CJXG, DJHA | 310 hp | 2016-2020 |
| Volkswagen Golf 8 GTI | DLBA, DNPA, DRNA | 245 hp | from 2020 |
| Volkswagen Polo R WRC 6R | CDLJ | 220 hp | 2013-2014 |
| Volkswagen Scirocco 3 | CAWB | 200 hp | 2008-2009 |
| Volkswagen Scirocco 3 | CCZB | 210 hp | 2009-2017 |
| Volkswagen Scirocco 3 R | CDLC | 256 hp | 2009-2017 |
| Volkswagen Scirocco 3 R | CDLA | 265 hp | 2009-2017 |
| Volkswagen Scirocco R | CDLK | 280 hp | 2014-2017 |
Why is it the most cost-effective solution?
The original head bolts are sized for stock power: the more boost pressure rises, the harder the gasket and the fasteners work. ARP2000 studs carry a clearly higher clamp load and keep the gasket pressed down; removing the cylinder head a second time, with a new gasket and labour, costs far more than the kit.
Consider a reinforced head gasket
Reinforced fasteners are only fully worthwhile with a head gasket able to resist the same pressure. We offer the following part for this engine:
| Reinforced cylinder head gasket EA113 → |
-
Brand
-
ReferenceARP-204-4302
-
In stock2 Items
-
EAN130672036041274

