Skip to content
  • In stock
product product product product product product

Tri-metal crankshaft main bearings VAG 1.8 2.0 TFSI TSI EA888 Gen.1/Gen.2

€132.78 (tax incl.)
€147.53 (tax incl.) -10%

Set of 10 tri-metal crankshaft main bearing half shells for VAG 1.8 and 2.0 TFSI EA888 Gen 2 engines (Ø 57.96 mm).

  • Brands: ACL Race and King Racing
  • Fitments: Golf V and VI, Scirocco, Passat, Audi A3, A4, A5, TT, Seat Leon, Skoda Octavia, KTM X-Bow
  • Engine codes: CAEA, CAEB, CBFA, CCZA, CDNB, CPMA, CESA and others
  • Available sizes: standard to +0.25 mm, increased clearance versions (HX / STDX)
5M5563H-STD
30 in stock in Europe (72h lead time)
Available in stock in Europe (72h lead time)
Pay in installments

The VAG 1.8 and 2.0 TFSI EA888 Gen 2 engines

The EA888 Gen 2 is a direct-injection turbocharged four-cylinder from the Volkswagen group, built as 1.8 and 2.0 litre units (TFSI, TSI) for Audi, Volkswagen, Seat, Skoda and the KTM X-Bow. All the engines listed below share the same crankshaft journal and housing dimensions: a single bearing set covers the whole family.

The crankshaft of these engines runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series and KING RACING tri-metal sets shown here replace them on built engines.

Tri-metal main bearings

In a trimetal bearing, a steel back carries a copper-lead intermediate layer with high load capacity, itself covered by an anti-friction running layer that spares the main journal. The set is supplied complete: 10 half shells, i.e. 5 pairs.

Trimetal targets high, sustained loads, whereas aluminium bi-metal is limited to low to medium loads: about 8,000 psi for the latter, up to 12,000 psi for a performance trimetal, 50% more. The benefit shows in strength and durability on turbo, supercharged and high-revving engines.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankshaft journal Ø 57.958 / 57.978 mm
Housing bore Ø 63.000 / 63.019 mm
Width 15.5 mm
King bearings
Crankshaft journal Ø 57.96 / 57.98 mm
Housing bore Ø 63.000 / 63.017 mm
Width 15.4 mm

Manufacturer's note (ACL 5M5563H): suits EA888 Gen 2 engines.

ReferenceBrand and treatmentSizeWall thickness (mm)
5M5563H-STD ACL Race - Untreated Standard 2.504
5M5563HX-STD ACL Race - Untreated Std, increased clearance (HX) 2.491
5M5563H-.025 ACL Race - Untreated +0.025 2.5165
5M5563H-.25 ACL Race - Untreated +0.25 2.629
MB5778XP King Racing - Untreated Standard 2.504
MB5778XP STDX King Racing - Untreated Std, increased clearance (STDX) 2.491
MB5778XP.026 King Racing - Untreated +0.026 2.517
MB5778XP0.25 King Racing - Untreated +0.25 2.631

Running clearance

Running clearance is the gap between the bearing and the main journal, filled by the oil film.

While the engine turns, the main journal floats on this oil film, which carries the load without direct contact with the bearing. Film thickness depends on clearance: too tight, oil passes poorly, temperature rises and the risk of seizure grows; too wide, oil escapes, the film carries less and oil pressure decreases. A correct clearance ensures both sufficient lubrication and a well-maintained film.

Size / gradeWhen to choose itACL Race SeriesKing XP
Standard (STD) Standard journal, not reground 0.059 to 0.071 mm 0.058 mm - 0.071 mm
Increased clearance (HX / STDX) Wider clearance: high oil flow, high rpm 0.085 to 0.096 mm 0.083 mm - 0.096 mm
+0.025 / +0.026 mm Polished journal 0.059 to 0.071 mm 0.058 mm - 0.071 mm
+0.25 mm Journal reground to 0.25 mm 0.059 to 0.071 mm 0.058 mm - 0.071 mm

Check at assembly: lay a calibrated strip (Plastigauge) on the journal, tighten the main cap following the manufacturer's procedure, then compare the width of the crushed strip with the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

These ACL and King trimetal main bearings are aimed at built engines and racing: where a standard bearing quickly reaches its limit, they accept more power, more rpm and more boost. The range includes the standard size, a +0.025 / +0.026 mm size for a main journal that has only been polished, a +0.25 mm regrind size and the HX / STDX version with increased clearance for high-revving engines or engines needing a high oil flow. It allows the same part number to be kept after the crankshaft is reground and the clearance to be tailored to the oil used and the engine's duty.

The two brands

ACL An Australian specialist in high-performance engine bearings since 1949, ACL Bearing Company produces the Race Series: precisely made trimetal bearings, available in numerous sizes and recognised on built engines across the world.
King Racing Since the 1960s, Israel's King Engine Bearings has built high-performance engine bearings; its pMax Black trimetal alloy bearings are sized for heavy loads.

Construction and advantages

Criterion ACL Race Series King Racing
Cross-section Cross-section of an ACL Race Series trimetal bearing Cross-section of a King Racing trimetal bearing
Type High-performance trimetal bearing High-performance trimetal bearing
Country of manufacture Australia Israel
Construction Trimetal: steel back, copper layer, soft surface Trimetal: steel back, copper layer, soft surface
Alloy Race Series (copper-lead) pMax Black (hardened copper-lead)
Protective coating No No
Available sizes Standard to +0.25 mm (+ increased clearance HX) Standard to +0.25 mm (+ increased clearance STDX)

Vehicle compatibility

This main bearing set fits the VAG 1.8 and 2.0 TFSI EA888 Gen 2 engines sharing the same crankshaft journal and housing dimensions:

BrandModel (chassis)Engine codePowerYears
Audi A3 (8P1) BYT, BZB, CAWB, CBFA, CCTA, CCZA 160–200 hp 2004–2012
Audi A3 Convertible (8P7) BZB, CAWB, CCZA 160–200 hp 2008–2013
Audi A3 Sportback (8PA) BYT, BZB, CAWB, CBFA, CCTA, CCZA 160–200 hp 2004–2013
Audi A4 Allroad B8 (8KH) CDNC, CPMA, CPMB 211–220 hp 2009–2016
Audi A4 B8 (8K2) CABA, CABB, CAEA, CAEB, CAED, CDNB, CDNC, CFKA, CPMA, CPMB 120–220 hp 2007–2015
Audi A4 B8 Avant (8K5) CABB, CAEB, CDNB, CDNC, CFKA 160–211 hp 2007–2015
Audi A5 (8T3) CAEB, CAED, CDNB, CDNC, CPMA, CPMB 180–220 hp 2008–2017
Audi A5 Convertible (8F7) CAEA, CAEB, CAED, CDNB, CDNC, CPMA, CPMB 180–220 hp 2009–2017
Audi A5 Sportback (8TA) CDNB, CDNC 180–211 hp 2009–2017
Audi A6 C7 (4G2, 4GC) CAEB, CAED, CDNB, CHJA 180–245 hp 2011–2018
Audi A6 C7 Avant (4G5, 4GD) CDNB 180 hp 2011–2018
Audi A8 D4 (4H2, 4H8, 4HC, 4HL) CHJA 245 hp 2012–2015
Audi Q3 (8UB, 8UG) CCTA, CCZC, CPSA 170–211 hp 2011–2018
Audi Q5 (8RB) CAEB, CDNB, CDNC, CHJA, CPMA, CPMB 180–245 hp 2008–2017
Audi Q5 Van (8RB) CDNC 211 hp 2008–2012
Audi TT (8J3) CCTA, CCZA, CESA, CETA 200–211 hp 2006–2015
Audi TT Roadster (8J9) CCTA, CCZA, CESA, CETA 200–211 hp 2007–2014
Audi (Faw) A6L C7 (4X8, 4XL) CDNB 180 hp 2012–2016
Ktm X-Bow Convertible CAEB 240 hp 2008–
Seat Alhambra (710, 711) CCZA 200 hp 2010–2012
Seat Altea (5P1) BYT, BZB 160 hp 2007–2015
Seat Altea XL (5P5, 5P8) BYT, BZB, CCZB 160–211 hp 2007–2015
Seat Exeo (3R2) CDND 211 hp 2010–2013
Seat Exeo ST (3R5) CDND 211 hp 2010–2013
Seat Leon (1P1) BZB, CCZB 160–211 hp 2007–2012
Seat Toledo III (5P2) BYT, BZB 160 hp 2007–2009
Skoda Octavia II (1Z3) BZB, CCZA 160–200 hp 2005–2013
Skoda Octavia II Combi (1Z5) BZB, CCZA 160–200 hp 2005–2013
Skoda Superb II (3T4) BZB, CCZA 160–200 hp 2008–2015
Skoda Superb II Estate (3T5) CCZA 200 hp 2010–2015
VW Amarok (2HA, 2HB, S1B, S6B, S7A, S7B, AGD) CFPA 160 hp 2010–2016
VW Amarok Platform/Chassis (S1B, S6B, S7B) CFPA 160 hp 2011–2016
VW Beetle (5C1, 5C2) CBFA, CCTA, CCZA 200 hp 2011–2016
VW Beetle Convertible (5C7, 5C8) CBFA, CCTA, CCZA 200–213 hp 2011–2016
VW CC B7 (358) CBFA, CCTA, CCZB 200–210 hp 2011–2016
VW California T5 Camper (7EC, 7EF, 7EG, 7HF, 7HC) CJKB 150 hp 2012–2015
VW California T6 Camper (SGC, SGG, SHC) CJKB 150 hp 2015–2019
VW EOS (1F7, 1F8) CAWB, CBFA, CCTA, CCZA, CCZB 200–210 hp 2006–2015
VW Golf V (1K1) CAWB, CBFA, CCTA 200 hp 2004–2009
VW Golf V Variant (1K5) CAWB, CBFA, CCTA 200 hp 2007–2009
VW Golf VI (5K1) CBFA, CCTA, CCZB 200–210 hp 2009–2014
VW Golf VI Convertible (517) CCZB 211 hp 2012–2016
VW Golf VI Van (5K1) CCZB 211 hp 2009–2012
VW Golf VI Variant (AJ5) CCZA 200 hp 2009–2013
VW Jetta III (1K2) CAWA, CAWB, CBFA, CCTA 170–200 hp 2005–2010
VW Jetta IV (162, 163, AV3, AV2) CBFA, CCTA, CCZA 200 hp 2010–2014
VW Multivan T5 (7HM, 7HN, 7HF, 7EF, 7EM, 7EN) CJKB 150 hp 2012–2015
VW Multivan T6 (SGF, SGM, SGN, SHM, SHN) CJKB 150 hp 2015–2019
VW Passat Alltrack B7 Variant (365) CCZB 210 hp 2012–2014
VW Passat B6 (3C2) BZB, CAWB, CBFA, CCTA, CCTB, CCZA, CGYA 152–200 hp 2005–2010
VW Passat B6 Variant (3C5) BZB, CAWB, CBFA, CCTA, CCZA, CGYA 152–200 hp 2005–2011
VW Passat B7 (362) CCZB 210 hp 2010–2014
VW Passat B7 Van/Estate (365) CCZB 211 hp 2010–2014
VW Passat B7 Variant (365) CCZB 210 hp 2010–2015
VW Passat CC B6 (357) BZB, CAWB, CBFA, CCTA, CCZA, CCZB, CGYA 152–211 hp 2008–2012
VW Scirocco III (137, 138) CAWB, CCZB 200–210 hp 2008–2017
VW Scirocco Van (137) CCZB 211 hp 2009–2014
VW Sharan (7N1, 7N2) CCZA 200 hp 2010–2015
VW Sharan Van/monospace (7N1, 7N2) CCZA 200 hp 2010–2015
VW Tiguan (5N_) CAWA, CAWB, CCTA, CCTB, CCZA, CCZB, CCZC, CCZD 170–211 hp 2007–2018
VW Tiguan VAN (5N_) CCZA, CCZB, CCZC 170–211 hp 2009–2018
VW Transporter T5 Bus (7HB, 7HJ, 7EB, 7EJ) CJKB 150 hp 2012–2015
VW Transporter T5 Platform/Chassis CJKB 150 hp 2012–2015
VW Transporter T5 Van (7HA, 7HH, 7EA, 7EH) CJKB 150 hp 2012–2015
VW Transporter T6 / Caravelle T6 Bus CJKB 150 hp 2015–2019
VW Transporter T6 Platform/Chassis CJKB 150 hp 2015–2019
VW Transporter T6 Van (SGA, SGH, SHA, SHH) CJKB 150 hp 2015–2019

Why replace the bearings

Replacing the bearings during a build or rebuild guards against the most expensive failure: a worn-out main bearing scores the main journal, contaminates the oil circuit with debris and forces at least a crankshaft regrind, or even block repairs. Against such costs a new set weighs little: it is the cheapest part of the crankshaft assembly, but the one whose failure costs the most.

12 other products in the same category

Viewed products

Loading...