- On order
Forged connecting rods Mitsubishi - 2.0L 16V - 4G63 7-bolt (156 mm rod length, 22 mm pin) for forged pistons
Set of 4 forged connecting rods in 4340 steel for the Mitsubishi 2.0L 16V 4G63 7-bolt.
- Brands: Manley, ZRP
- Compatibility: Lancer Evo IV-IX, Eclipse/Talon 2G
- Engine code: 4G63
- Bolts included: ARP 2000, L19 or CA625+
The Mitsubishi 4G63 engine (7-bolt)
The 4G63 is the 2.0-litre turbocharged four-cylinder that built Mitsubishi's motorsport legend. Part of the 4G6 family, this cast-iron block with an aluminium head (16 valves, DOHC) displaces 1,997 cm³ with an 85 mm bore and an 88 mm stroke. From 1996 Mitsubishi switched to a flywheel secured by 7 bolts (hence the "7-bolt" name), stiffer than the earlier 6-bolt design.
This 7-bolt version powers the Lancer Evolution IV to IX as well as the second-generation Eclipse and Talon. Famously near-indestructible, the 4G63T easily withstands power figures well beyond stock once the rotating assembly is upgraded. The rods shown here are long rods with a 156 mm centre distance (versus 150 mm stock), favoured on stroker builds or to optimise the rod/stroke ratio of an aggressive build.
Forged connecting rods
Machined from high-strength forged alloy steel, these rods replace the factory parts whose limit shows as soon as boost and rpm climb. Forging aligns the metal grain with the loads, delivering fatigue and bending resistance far beyond a mass-produced rod.
Each set ships with its ARP high-performance hardware (ARP 2000, L19 or CA625+ depending on the variant), factory-fitted. The range covers H and I profiles, in 4340 steel and, for the ZRP "IP" version, in 817M40T steel, to suit circuit builds as well as the most demanding big-turbo and rally setups.
Technical specifications of the 4G63 forged rods (7-bolt, 156 mm centres)
| Reference | Brand | Profile | Hardware | Pin Ø OEM 22 mm | Small-end width | Big-end Ø OEM n.p. | Big-end width | Centres OEM 150 mm | Steel | Weight per rod |
|---|---|---|---|---|---|---|---|---|---|---|
| 14020-4 | Manley | H | ARP 2000-3/8"-38mm | 22 | 48 | 26,4 | 156 | 4340 | 545 | |
| 15020-4 | Manley | H-HD | ARP 2000-3/8"-38mm | 22 | 48 | 26,4 | 156 | 4340 | 635 | |
| 15020R6-4 | Manley | H-HD | ARP CA625+-3/8"-38mm | 22 | 48 | 26,4 | 156 | 4340 | 635 | |
| 14421-4 | Manley | I-HD | ARP 2000-3/8"-41mm | 22 | 48 | 26,4 | 156 | 4340 | 645 | |
| 14421R6-4 | Manley | I-HD | ARP CA625+-3/8"-41mm | 22 | 48 | 26,4 | 156 | 4340 | 645 | |
| R-MIT-007-I | ZRP | I-HD | ARP 2000-3/8"-38mm | 22 | 48 | 26,4 | 156 | 4340 | 612 | |
| R-MIT-007-I-L19 | ZRP | I-HD | ARP L19-3/8"-38mm | 22 | 48 | 26,4 | 156 | 4340 | 612 | |
| R-MIT-007-IP | ZRP | I | ARP L19-3/8"-38mm | 22 | 48 | 26,4 | 156 | 817M40T | 633 |
OEM reference: (set of 4 rods).
Torque and bolt stretch
| Rod | Hardware | Torque | Recommended stretch |
|---|---|---|---|
| Manley (14020-4) | ARP 2000 | 81,3 N·m | 0,147–0,157 mm |
| Manley (15020-4) | ARP 2000 | 81,3 N·m | 0,147–0,157 mm |
| Manley (15020R6-4) | ARP CA625+ | 88,1 N·m | 0,160–0,170 mm |
| Manley (14421-4) | ARP 2000 | 81,3 N·m | 0,147–0,157 mm |
| Manley (14421R6-4) | ARP CA625+ | 88,1 N·m | 0,165–0,190 mm |
| ZRP (R-MIT-007-I) | ARP 2000 | 61,0 N·m | 0,140–0,152 mm |
| ZRP (R-MIT-007-I-L19) | ARP L19 | 67,8 N·m | 0,152–0,165 mm |
| ZRP (R-MIT-007-IP) | ARP L19 | 67,8 N·m | 0,152–0,165 mm |
Manufacturers recommend the stretch method rather than a torque figure: the actual bolt elongation is measured with a dedicated gauge, ensuring an even preload. The values above are indicative and must always be confirmed against the hardware maker's documentation.
Technical guide
Forged 4340 steel: what is it?
| 4340 belongs to the family of nickel-chromium-molybdenum alloy steels, approved for aerospace as well as for motorsport. Hot forging aligns the grain flow of the metal with the loads the rod actually sees; quenching followed by tempering then sets a rare balance between hardness, fatigue life and the ability to deform rather than snap. Against a production rod, usually sintered and drawn up around industrial cost, the gap is measurable: around 19% more yield strength, 8% more tensile strength and 19 to 37% more endurance, which multiplies service life under alternating loads. On a 4G63 running higher boost pressure, that reserve makes all the difference. |
Rod profiles
![]() |
H profile. Made up of two wide flat flanks joined by a central web, its H-shaped section gives the rod a massive, even silhouette along its entire length. On a turbo engine such as the 4G63, it is a robust and versatile profile, designed for mainstream builds: from strengthening the bottom end when switching to forged pistons to a measured increase in boost pressure. Its H-HD (H-Tuff) version is a reinforced, thicker variant intended for high boost levels. |
![]() |
I profile. Thanks to its slimmer central section, bordered by two flanges that create its I shape, the rod keeps high rigidity for a controlled mass. It is the profile of choice for modern turbo engines such as the 4G63, where it serves both bottom-end reliability and increases in boost pressure. Its I-HD (Heavy Duty) version, known as Pro Series I-Beam Turbo Tuff at Manley, has a reinforced, thicker body: it is aimed at extreme loads, with a turbo, supercharger or nitrous oxide. |
How to choose your rod hardware? 
The rod bolt is one of the most heavily loaded parts of the engine. Every variant here uses ARP hardware in 3/8" diameter, a guarantee of reliability at high rpm. The grade choice depends on target power and budget.
| ARP 2000. Tensile strength around 220,000 psi (≈ 1,517 MPa). In 3/8", it secures about 200 hp per cylinder and rpm up to 8,500. The most common grade, recognised for its strength and versatility. | |
![]() |
ARP L19. Very high strength grade (≈ 260,000 psi) for hard-driven engines: in 3/8", it allows about 250 hp per cylinder and rpm up to 10,000. Corrosion-sensitive, it requires oiled storage. |
| ARP CA625+. Premium alloy steel designed for extreme environments (endurance, big-turbo). In 3/8", it is reserved for builds beyond 250 hp per cylinder and rpm beyond 10,000. Superior strength and fatigue life, with no particular storage constraint. |
Measuring bolt stretch

| Stretch method. Rather than relying on torque alone, bolt elongation is measured with a stretch gauge: the only method that guarantees an exact, repeatable preload, essential to rod integrity at high rpm. |
Discover the ARP stretch gauge
The brands offered
This page brings together two benchmark manufacturers, selected for their forging quality and motorsport reputation.
| Manley Performance. American manufacturer of competition engine parts since 1966. Its rods are machined from vacuum-degassed aerospace-grade 4340 steel, shot-peened to improve fatigue life and then inspected individually before shipping. The Turbo Tuff range, widely used on tuned 4G63 engines in the United States, is fitted with ARP 2000 or ARP L19 bolts depending on the target power. | |
![]() |
ZRP. Forged connecting rods designed by Alex Drakos in Athens, Greece, purely for competition use. Every part is forged from 4340 steel, machined and then weight-matched to ±1 g so the engine stays balanced at high rpm. On the 7-bolt 4G63, ZRP covers the H and I profiles with ARP 2000, ARP L19 or Custom Age 625+ bolts depending on the level of tune. |
Glossary
![]() |
1) Small end 2) Small-end diameter 3) Rod beam 4) Rod bolt 5) Big end 6) Rod nut / bolt 7) Rod cap 8) Big-end diameter 9) Center-to-center |
Vehicle compatibility of the Mitsubishi 4G63 engine (7-bolt)
Below are the vehicles fitted with the Mitsubishi 2.0L 16V 4G63 7-bolt engine. Measuring the piston pin diameter and the rod length remains essential before any order. Variant concerned: 156 mm rod length, 22 mm pin.
| Brand | Model (chassis) | Engine code | Power | Years |
|---|---|---|---|---|
| Mitsubishi | Lancer Evolution IV–VI (CN9A/CP9A) | 4G63T | 280 hp | 1996–2001 |
| Mitsubishi | Lancer Evolution VII–IX (CT9A) | 4G63T | 280 hp | 2001–2007 |
| Mitsubishi | Eclipse GST / GSX 2G (D30) | 4G63T | 210 hp | 1995–1999 |
| Eagle | Talon TSi 2G | 4G63T | 210 hp | 1995–1998 |
Why is it the most economical solution?
On a 4G63 that has thrown a rod, putting it back to standard is never an isolated job: the matching piston is destroyed, the crankshaft marked, sometimes the block needs boring. Added together, those original parts cost as much as a proper build, only to recover exactly the limits that caused the failure.
The same budget spent on forged 4340 rods and forged pistons changes the picture completely: the safety margin grows, the rotating assembly copes with pressures and revs the standard engine never saw, and power can be raised later without opening the bottom end again.
For comparable spending: more reliability, more durability, more potential.
-
Brand
-
Reference14020-4




