Skip to content
  • On order
Reinforced head gasket Ford 2.0 EcoBoost - C15317-027 Reinforced head gasket Ford 2.0 EcoBoost - C15317-027 Reinforced head gasket Ford 2.0 EcoBoost - C15317-027 Reinforced head gasket Ford 2.0 EcoBoost - C15317-027

Reinforced cylinder head gasket Ford Focus ST Mondeo S-MAX Kuga 2.0 EcoBoost R9DA R9DB R9DC R9DD TPBA TNBA TNWA TNWB TPWA

€119.30 (tax incl.)
€159.07 (tax incl.) -25%

Reinforced Cometic multilayer MLS head gasket for Ford 2.0 litre EcoBoost engines, Focus ST, Mondeo, Galaxy, S-MAX and Kuga.

  • Engines: R9DA, R9DB, R9DC, R9DD, TPBA, TNBA, TNWA, TNWB, TPWA
  • Bore: 89 mm
  • Thicknesses: 0.69 to 3.56 mm
  • Replaces: 5149932, 1 682 135
C15317-027
0 in stock in France
On order, 15 to 30 days lead time
Pay in installments

The Ford engines covered

The Ford R9DA, R9DB, R9DC, R9DD, TPBA, TNBA, TNWA, TNWB and TPWA petrol engines, of 2.0 litres, are fitted to the Ford Focus III, Mondeo IV, Galaxy II, S-MAX and Kuga II models listed below.

The original gasket part numbers for these engines are 5149932 and 1 682 135. Ford publishes neither the bore, nor the construction, nor the thickness. It is designed for standard combustion pressure: as that pressure rises, the clamping load relaxes, the cylinder head lifts and coolant seeps into a cylinder.

Reinforced cylinder head gaskets

The head gasket does not seal on its own: the fasteners that clamp the head onto the block matter just as much. Above 100 N/mm², a composite gasket is crushed for good, whereas the 301 stainless steel of MLS gaskets withstands 517 N/mm², 5 times more, and recovers its shape at every combustion.

This page brings together the part numbers of Cometic, an American maker of racing gaskets, for a single construction: the multi-layer steel MLS. Every gasket has a 89 mm bore and thicknesses from 0.69 to 3.56 mm, enough to adjust the compression ratio without touching the pistons or the cylinder head. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM 5149932 | 1 682 135
89 mm 0.69 mm 4.29 MLS Cometic C15317-027
89 mm 0.76 mm 4.73 MLS Cometic C15317-030
89 mm 0.86 mm 5.35 MLS Cometic C15317-034
89 mm 0.91 mm 5.66 MLS Cometic C15317-036
89 mm 1.02 mm 6.35 MLS Cometic C15317-040
89 mm 1.14 mm 7.09 MLS Cometic C15317-045
89 mm 1.30 mm 8.09 MLS Cometic C15317-051
89 mm 1.42 mm 8.83 MLS Cometic C15317-056
89 mm 1.52 mm 9.46 MLS Cometic C15317-060
89 mm 1.68 mm 10.45 MLS Cometic C15317-066
89 mm 1.78 mm 11.07 MLS Cometic C15317-070
89 mm 1.91 mm 11.88 MLS Cometic C15317-075
89 mm 2.03 mm 12.63 MLS Cometic C15317-080
89 mm 2.18 mm 13.56 MLS Cometic C15317-086
89 mm 2.34 mm 14.56 MLS Cometic C15317-092
89 mm 2.49 mm 15.49 MLS Cometic C15317-098
89 mm 3.05 mm 18.97 MLS Cometic C15317-120
89 mm 3.56 mm 22.15 MLS Cometic C15317-140

The volume of a gasket is the space it leaves open above each cylinder. It is added to the combustion chamber and lowers the compression ratio the more it grows. Compare this figure only between gaskets of the same bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts R9DA, R9DB, R9DC, R9DD, TPBA, TNBA, TNWA, TNWB, TPWA not published by the manufacturer

Before fitting, lay a straight edge across the head and block faces to check they are flat, and have them resurfaced if necessary. Do not add any sealing paste: Cometic gaskets are delivered already coated.

Technical guide

The construction offered

Cometic MLS cylinder head gasket MLS Cometic
Stainless steel layers, stamped and joined with rivets. The outer layers carry active beads around every cylinder and every fluid passage. A moderate tightening torque is enough to seal, and the bore distorts very little. This versatile design covers everything from the tuned naturally aspirated engine to moderate boost.

Choosing bore and thickness

Gasket bore. The Cometic MLS is offered in 89 mm (C15317), in that bore only.

Thickness. The thickness of the original gasket is not published by Ford. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness is not published: measure the gasket taken off and keep the offered value closest to that reading
Skimmed cylinder head, make up the lost height The offered value closest to the thickness measured on the original gasket, plus the metal taken off at resurfacing
Forced induction build, lower the ratio A thickness above the one measured on the original gasket when it came off
Naturally aspirated build, raise the ratio A thickness under the one measured on the original gasket at removal, as low as 0.69 mm, the thinnest value offered

Should you choose a thickness under the original one, read with a dial gauge how high the pistons rise above the block deck: the reading gives the clearance remaining between piston and head.

The brand

Cometic Cometic Gasket, Inc. is an American manufacturer of engine gaskets and sealing solutions, established in 1989 in Concord, Ohio. It specialises in the custom gasket, cut to the bore and thickness required. Its entire output stays in the United States and uses American materials.

Advantages over the original gasket

Criterion Original gaskets 5149932 and 1 682 135 Reinforced gaskets
Construction Construction not stated by the manufacturer Multi-layer stainless steel (MLS)
Gasket bore not published 89 mm
Thicknesses available thickness not published by the manufacturer 0.69 to 3.56 mm, 18 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the bore of the original gasket, not published by Ford covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Brand Model Engine code Power Years
Ford S-MAX 2.0 EcoBoost TPWA 240 hp 2010-2014
Ford MONDEO IV 2.0 EcoBoost TPBA 240 hp 2010-2015
Ford MONDEO IV Turnier 2.0 EcoBoost TPBA 240 hp 2010-2015
Ford S-MAX 2.0 EcoBoost TNWA 203 hp 2010-2014
Ford GALAXY II 2.0 EcoBoost TNWA 203 hp 2010-2015
Ford MONDEO IV 2.0 SCTi TNBA 203 hp 2010-2015
Ford MONDEO IV Turnier 2.0 SCTi TNBA 203 hp 2010-2015
Ford KUGA II 2.0 TPWA 243 and 249 hp 2013-
Ford KUGA II 2.0 4x4 TPWA 240, 243 and 249 hp 2012-
Ford FOCUS III Turnier 2.0 ST R9DB 250 hp 2012-2020
Ford FOCUS III Turnier 2.0 ST R9DC 250 hp 2012-2020
Ford FOCUS III Turnier 2.0 ST R9DD 250 hp 2012-2020
Ford FOCUS III Turnier 2.0 ST R9DA 250 hp 2012-2020
Ford FOCUS III 2.0 ST R9DB 250 hp 2012-2017
Ford FOCUS III 2.0 ST R9DC 250 hp 2012-2017
Ford FOCUS III 2.0 ST R9DD 250 hp 2012-2017
Ford FOCUS III 2.0 ST R9DA 250 hp 2012-2017
Ford GALAXY II 2.0 EcoBoost TNWB 199 hp 2010-2015
Ford S-MAX 2.0 EcoBoost TNWB 199 hp 2010-2014
Ford MONDEO IV Berline tricorps 2.0 SCTI TNBA 203 hp 2010-2015
Ford MONDEO IV Berline tricorps 2.0 EcoBoost TPBA 240 hp 2010-2014
Ford MONDEO IV Van 2.0 EcoBoost TPBA 239 hp 2010-2014
Ford MONDEO IV Van 2.0 EcoBoost TNBA 203 hp 2010-2014
Ford GALAXY MK II VAN 2.0 EcoBoost TNWA 203 hp 2010-2015
Ford S-MAX VAN 2.0 EcoBoost TNWA 203 hp 2010-2014
Ford S-MAX VAN 2.0 EcoBoost TPWA 239 hp 2010-2014
Ford KUGA II 2.0 Ecoboost Traction avant TPWA 240 hp 2012-2017

OEM part number: 5149932 and 1 682 135.

Important: the part numbers on this page fit only the R9DA, R9DB, R9DC, R9DD, TPBA, TNBA, TNWA, TNWB and TPWA engines: check your vehicle's engine code before placing an order.

Why switch to a reinforced gasket?

Once the original gasket has reached its limit, the reinforced gasket takes over: under higher combustion pressure it holds its shape and is not crushed.

Add a turbo or a supercharger, or increase the compression ratio, and the head gasket becomes the most heavily stressed part of the top end. A reinforced gasket avoids the leak and the cylinder head removal that would follow.

4 other products in the same category

Viewed products

Loading...