Skip to content
  • On order
Reinforced inlet valves MITSUBISHI 4G63 Reinforced inlet valves MITSUBISHI 4G63

Reinforced inlet valves MITSUBISHI 4G63

€180.71 (tax incl.)
€225.89 (tax incl.) -20%

Set of 8 reinforced inlet valves for MITSUBISHI 4G63.

  • Brands: FERREA, SUPERTECH
  • Engines: 4G63 and 4G63T 2.0 16V
  • Dimensions: 34, 34.5, 35 or 36 mm head, 6.57 mm stem
  • Material: stainless steel (including EV8) with chrome-plated stem or black nitride stainless steel
F6026*8
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

MITSUBISHI engines covered

The twin-cam 4G63 is Mitsubishi's 2-litre, 16-valve four-cylinder, naturally aspirated or turbocharged (4G63T). It powers the first and second generation Eclipse and the Lancer Evolution VIII, two very popular bases for tuning.

It has 8 inlet valves, two per cylinder. Raised boost, sharper camshafts or a higher rev limit load them well beyond what the production engine was designed for.

FERREA and SUPERTECH reinforced inlet valves

In the 4G63, the inlet valve opens the door to the incoming air and shuts it again, dozens of cycles each second while the turbo blows and the rev counter climbs. As it closes each time, its head taps against the seat, and the stem carries on its back-and-forth through the guide without rest. The thermal range runs from 400 to 550 °C; at that level an ordinary chrome-silicon steel is already weakening, from 500 MPa at 500 °C down to 250 MPa at 600 °C, barely higher, hence a 50 % loss. Raising lift, spring firmness, revs or boost adds shocks, friction and heat.

FERREA's 6000 series uses EV8 stainless, its stem hard chrome plated: 650 MPa kept at 500 °C and 550 MPa at 600 °C, 30 % then 120 % above chrome-silicon steel. As for the Competition Plus, a stainless valve with a chromed stem, it is 20 % tougher when hot and when loaded again and again, and stretches seat life by 25 %. SUPERTECH supplies a racing stainless related to EV8, black nitrided: the hardened, smoothed surface guards the stem against wear in its guide.

Wider than the 34 mm standard head, the head goes to 34.5, 35 or 36 mm without changing stem or length: the seat opening gets bigger, the chamber fills more fully and power rises, once all 8 inlet seats are recut to the chosen diameter by a cylinder head specialist.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
F6026*8 FERREA Standard 34 mm 6.57 mm 109.7 mm EV8 stainless steel, hard chrome stem
F6052*8 FERREA +1 mm 35 mm 6.57 mm 109.7 mm EV8 stainless steel, hard chrome stem
F1826P*8 FERREA Standard 34 mm 6.57 mm 109.7 mm Stainless steel, chrome-plated stem
F1452P*8 FERREA +1 mm 35 mm 6.57 mm 109.7 mm Stainless steel, chrome-plated stem
MIVN-1007-8 SUPERTECH Standard 34 mm 6.57 mm 109.6 mm Black nitride stainless steel
MIVN-1008-8 SUPERTECH +0.5 mm 34.5 mm 6.57 mm 109.6 mm Black nitride stainless steel
MIVN-1009-8 SUPERTECH +1 mm 35 mm 6.57 mm 109.6 mm Black nitride stainless steel
MIVN-1010-8 SUPERTECH +2 mm 36 mm 6.57 mm 109.6 mm Black nitride stainless steel

F6026, F1826P and MIVN-1007 are standard size; MIVN-1008 is +0.5 mm, F6052, F1452P and MIVN-1009 are +1 mm, MIVN-1010 is +2 mm.

Fitting details

PartMITSUBISHI originalReinforced
Collets K10035
Valve stem seals VS-M6.6I-8
Valve guide GDE-MI66-STI-8

The K10035 collets must suit the groove of the chosen valve: check this before compressing the springs.

At 34 mm the inlet seats keep their factory size; from 34.5 to 36 mm the workshop machines all 8 seats to the head diameter.

Technical guide

The brands offered

FERREA Located in Florida since 1978, in Fort Lauderdale, FERREA was started by two Argentine engine builders. All its one-piece valves, from the 6000 series to the Competition Plus, come from a forged bar and are fully CNC machined; they run in NASCAR and drag racing engines.
SUPERTECH For over thirty years, SUPERTECH Performance has been developing racing valves, springs and guides in San Jose, California. Each batch undergoes ultrasonic probing, radiography and laser measurement, then proves itself on circuit and drag engines.

How to choose

Collets lodged in the groove near the stem tip hold the upper retainer there. All these valves use that layout: pick the size, then the series or brand.

CriterionOption 1Option 2
Size Standard, 34 mm
To fit on a head whose inlet seats are intact and untouched: FERREA F6026*8 (6000 series) or F1826P*8 (Competition Plus), SUPERTECH MIVN-1007-8. The right pick for a 4G63 driven daily or a faithful stock restoration, with no machining at all.
+0.5 to +2 mm, 34.5 to 36 mm
A widened seat passes more air and brings about 10 to 12 cfm for every extra mm of head diameter. Seats are recut to suit, preferably along with port work; these sizes also rescue seats recut earlier. FERREA F6052*8 and F1452P*8, SUPERTECH MIVN-1008-8 to MIVN-1010-8.
FERREA series 6000 series, EV8 stainless
EV8 stainless whose stem is hard chrome plated, still rated 650 MPa at 500 °C. A solid base for a tuned turbo 4G63, at standard size or +1 mm, 109.7 mm long.
Competition Plus, chromed stem
20 % more strength in heat and fatigue, seat 25 % longer lasting. The series aimed at high boost pressures and sustained revs.

When reinforced valves become necessary

  • More turbo boost or a bigger turbocharger
  • Sharper cam profiles or much stiffer valve springs
  • Red line moved higher up
  • Head prepared for rally, track or drag racing
  • Stock valves damaged or seats already recut before

Compatible vehicles

ModelEngine codePowerYears
Eclipse I (D2_A) 2.0 16V / 2.0 Turbo 4G63 / 4G63T 1989-1995
Eclipse II (D3_A) 2000 GS 16V / Turbo 16V 4G63 / 4G63T 1994-1999
Lancer VII (CT9A) EVO VIII 4G63T 2003-2007
Important: a set of 8 is enough for a complete engine. The SUPERTECH valves are intended for the twin-cam turbo 4G63. The Eagle Talon, sold in the United States, is not covered by this listing.

Related products

With the 4G63 head off, take the chance to renew the 8 exhaust valves too and to fit fresh stem seals, using the reinforced parts on the next page:

MITSUBISHI 4G63 exhaust valves →
Reinforced valve spring kit Mitsubishi 4G63T →

16 other products in the same category

Viewed products

Loading...