Skip to content
  • On order
Reinforced inlet valves BMW B58B30 Reinforced inlet valves BMW B58B30

Reinforced inlet valves BMW B58B30

€388.68 (tax incl.)
€485.86 (tax incl.) -20%

Set of 12 reinforced inlet valves for BMW B58B30 (M140i, M240i, 340i, M340i, 440i, 540i, Z4 M40i).

  • Brands: SUPERTECH, FERREA
  • Engines: B58B30, B58B30B, B58B30C
  • Dimensions: 30.1 mm or 30.6 mm head, 5 mm stem
  • Material: black nitride stainless steel, single groove (SUPERTECH); FERREA 3 grooves
F2431P*12
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

BMW engines covered

The B58B30 is BMW's 3.0 litre turbocharged inline six, with roller finger followers, hydraulic lash adjustment and Valvetronic variable lift on the inlet side. Since 2015 it has powered the M140i, M240i, 340i, M340i, 440i, 540i and Z4 M40i, with 326 to 387 hp depending on version.

Its 12 inlet valves are BMW 11 34 7 633 699: 30.1 mm head, 5 mm stem, held by collets 11 34 1 438 142. A remap that raises boost exposes them to more heat and harder impacts.

SUPERTECH and FERREA reinforced inlet valves

On the B58, each inlet valve lifts and falls back at a pace of several dozen cycles a second as revs climb, letting through the air the turbo has compressed. On closing, its head hits the seat machined in the cylinder head; meanwhile the stem keeps running through the guide. It operates between 400 and 550 °C, where standard chrome-silicon steel starts to give way: 500 MPa at 500 °C, then 250 MPa at 600 °C, one notch higher, 50 % less strength. More lift, firmer springs, extra revs or raised boost make these blows, this rubbing and this heat harsher.

The SUPERTECH valve is cut from a racing stainless of the EV8 family, which retains 650 MPa at 500 °C, 30 % beyond the factory steel, and 550 MPa at 600 °C, 120 % better. Thanks to black nitriding, the outer layer gains hardness and polish, so the stem rubs less and wears less in its guide. FERREA supplies its Competition Plus line here, built in stainless and fitted with a chromed stem; it copes 20 % better with heat and fatigue cycles and extends seat life by 25 %. The B58 therefore takes two finishes: black nitride stainless from SUPERTECH or a chrome stem from FERREA.

FERREA also lists a +0.5 mm oversize, taking the head from 30.1 to 30.6 mm while the stem stays at 5 mm. This slightly wider head clears more section at the seat; each cylinder fills better and power follows, as long as the inlet seats are recut accordingly.

Inlet valve technical specification

Part numberBrandSizeHead Ø
OEM 30.1 mm
Stem Ø
OEM 5 mm
LengthGroovesMaterial
MCIVN-1400S-12 SUPERTECH Standard 30.1 mm 5 mm 99.5 mm 1 Black nitride stainless steel
F2431P*12 FERREA Standard 30.1 mm 5 mm 99.2 mm 3 Stainless, chrome stem
F2434P*12 FERREA +0.5 mm 30.6 mm 5 mm 99.2 mm 3 Stainless, chrome stem

MCIVN-1400S-12: to be fitted with KPR-5.0-7S collets.

Fitting details

PartBMW originalReinforced
Valve collets 11 34 1 438 142 KPR-5.0-7S (1 groove)
Valve stem seals Kit 11 34 0 034 068 VSI-BM50-I-12 (inlet)
Valve guide

With its single groove, the SUPERTECH valve is fitted only with KPR-5.0-7S collets, never with the original ones. The FERREA valves keep 3 grooves and take 3-groove collets for a 5 mm stem.

The +0.5 mm version requires the inlet seats to be cut to its size; at standard size, the seats are checked and refreshed as usual during the cylinder head rebuild.

Clearance is taken up hydraulically: no adjustment is needed after replacing the valves.

Technical guide

Our brands

SUPERTECH SUPERTECH Performance has made racing valves, springs and retainers in San Jose, California, for three decades. Each part number is designed for its engine, screened by ultrasound, radiography and laser, then put to the test with tuners, from circuit to drag strip.
FERREA FERREA Racing Components set up in 1978 in Fort Lauderdale, Florida, on the initiative of two Argentine-born engine builders, and still carries out all its production. Its valves, forged in one piece from bar then fully CNC machined, compete in NASCAR, on drag strips and on circuits.

How to choose

Near the stem tip, the groove receives the collets holding the valve beneath the retainer. Its design sets how firmly it is held, and what it gives.

CriterionOption 1Option 2
Size Standard size
30.1 mm head, matching the BMW valve, at SUPERTECH and FERREA. Meant for heads whose seats have never been recut.
+0.5 mm oversize (FERREA)
30.6 mm head: a slightly wider opening at the seat passes more air, roughly 10 to 12 cfm per mm of head, to the benefit of power. The seats are machined to this diameter; seats that were already reground are recovered this way.
Grooves 3 grooves (FERREA)
Fitting close to the original one, the stem keeping its freedom to rotate. A good choice for a road car keeping stock springs and revs; new 3-groove collets for a 5 mm stem recommended. Limit: at high revs, the lowest groove, the narrowest section, takes most of the shocks.
Single groove (SUPERTECH)
The KPR-5.0-7S collets, the only ones allowed and preferably new, pinch the stem: almost no load reaches the groove and the enlarged contact rubs less. The valve thus tolerates firmer springs, aggressive lift and high revs; this is the SUPERTECH answer to big power, in circuit, drift or rally.

When reinforced valves become necessary

  • Camshafts with more lift or uprated return springs
  • Rev limit raised
  • Higher boost or a larger turbocharger
  • Cylinder head reconditioned for track, drift or rally events
  • Marked, worn or already reworked stock valves

Compatible vehicles

ModelEngine codePowerYears
M140i (F20 / F21) B58B30 340 hp 2015-
M240i (F22 / F87) B58B30 340 hp 2015-2021
M240i (G42) B58B30B 374 hp 2021-
340i (F30) B58B30 326-360 hp 2015-2018
M340i (G20) B58B30 374-387 hp 2019-
440i (F32 / F82) B58B30 326-360 hp 2016-
540i (G30) B58B30 340-360 hp 2016-2020
Z4 M40i (G29) B58B30C 340 hp 2018-

OEM part number (inlet valve): 11 34 7 633 699

Important: these sets are intended for the B58B30; the S58B30 of the M2, M3, M4, X3 M and X4 M uses another original valve (11 34 8 053 402) and is not covered here.

Related products

A rebuilt B58 head also needs new exhaust side valves and a full set of fresh valve stem seals. Suitable exhaust valves are listed here:

BMW B58B30 S58B30 exhaust valves →

15 other products in the same category

Viewed products

Loading...