- On order
Reinforced exhaust valves BMW M5 E34 S38B36 S38B38
Set of 12 reinforced exhaust valves for BMW M5 E34 S38B36 and S38B38.
- Brand: SUPERTECH
- Engines: S38B36, S38B38
- Dimensions: 32.0, 32.5 or 33.0 mm head, 7 mm stem
- Material: black nitride stainless steel or Inconel, 3 grooves
BMW engines covered
A naturally aspirated six-cylinder from the M division, the S38 powers the E34 M5 in two displacements: S38B36 of 3,535 cc (93.4 x 86 mm) from 1988 to 1992, then S38B38 of 3,795 cc (94.6 x 90 mm) from 1992 to 1995. Its 24 valve head, twin camshafts and individual throttle bodies give it the character of a road legal racing engine.
Its 12 exhaust valves have a 7 mm stem, held by collets 11 34 1 307 136 and sealed by the 11 34 9 059 172 seal kit. They are operated by mechanical shim tappets, so the valve length must match the type of tappet fitted. On an engine of this age, the exhaust valves are often marked or pitted when the head comes apart.
SUPERTECH reinforced exhaust valves
Every exhaust stroke bathes it in burnt gas: on a naturally aspirated unit such as the S38 the valve head runs at 760 to 870 °C, rising past 1,000 °C when boost is added. The seat drains roughly 75 % of that heat; about 20 % is left to the guide. As a benchmark, an EV8 steel drops from 550 MPa at 600 °C to just 300 MPa at 800 °C; abused, the head warps, stops seating and the seat ends up burnt.
Two materials are offered. The BMEVN valves use a high temperature stainless steel with black nitriding, which hardens the stem surface and cuts wear and friction. The BMEVI valves move up to Inconel, a nickel superalloy with 860 MPa at 732 °C and 554 MPa at 816 °C, close to 85 % stronger than EV8 steel near 800 °C: the one to pick for a boosted S38 or one driven hard on track.
The head comes in three sizes: 32.0 mm at the original size, 32.5 mm (+0.5 mm) and 33.0 mm (+1 mm). Being wider, it empties the cylinder sooner, leaves space for a bigger fresh charge and adds power; it needs exhaust seats recut to match its diameter.
Exhaust valve technical specifications
| Part number | Brand | Size | Head Ø OEM 32.0 / 32.5 mm | Stem Ø OEM 7 mm | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| BMEVI-1006L-12 | SUPERTECH | Standard | 32.0 mm | 7 mm | 125.0 mm | 3 | Inconel |
| BMEVN-1009-12 | SUPERTECH | +0.5 mm | 32.5 mm | 7 mm | 123.7 mm | 3 | Black nitride stainless steel |
| BMEVN-1009L-12 | SUPERTECH | +0.5 mm | 32.5 mm | 7 mm | 126.1 mm | 3 | Black nitride stainless steel |
| BMEVN-1010-12 | SUPERTECH | +1 mm | 33.0 mm | 7 mm | 123.7 mm | 3 | Black nitride stainless steel |
| BMEVN-1010L-12 | SUPERTECH | +1 mm | 33.0 mm | 7 mm | 126.1 mm | 3 | Black nitride stainless steel |
| BMEVI-1010-12 | SUPERTECH | +1 mm | 33.0 mm | 7 mm | 123.7 mm | 3 | Inconel |
The long valves (BMEVI-1006L, BMEVN-1009L, BMEVN-1010L) are fitted with CF-37.5/3.1+ cam followers and their shims, the short valves with CF-37.5/5.65+ cam followers; some European S38 versions use 35 mm cam followers.
Valve fitting
| Part | BMW original | Reinforced |
|---|---|---|
| Collets | 11 34 1 307 136 (3 grooves) | |
| Valve stem seals | Kit 11 34 9 059 172 | VS-VW7E-12 (exhaust) |
| Valve guide | Inner Ø 7.0 mm | GDE-BMS14-7 (manganese bronze) |
All valves on this page have 3 grooves: they take 7 mm 3 groove collets, preferably new, and the retainers of the original assembly.
The 32.0 mm standard version keeps the exhaust seats as they are, simply checked during the cylinder head rebuild; the 32.5 and 33.0 mm heads require the seats to be cut to size.
Before ordering, check the type of tappet in the cylinder head: it decides between the long and short versions.
Technical guide
Our brand
| SUPERTECH Performance, a Californian brand from Silicon Valley, brings more than 30 years of experience in titanium retainers, guides, springs and racing valves. Stainless, titanium, Inconel: the material changes, but each valve is engineered engine by engine with tuners active in drag, rally and circuit racing. |
How to choose
Every version keeps the 3 grooves of the BMW part, in which the collets lock in under the spring retainer; the choice therefore comes down to head size and to length, which follows the fitted tappet:
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard, 32.0 mm Original seats never touched: no machining is needed for fitting. This size exists only in Inconel, in the long length. |
Enlarged, 32.5 or 33.0 mm The wider head clears burnt gases better and helps filling, at the cost of seats recut to the new diameter. Also makes up for seats already ground. Nitrided stainless in short or long; Inconel in 33.0 mm short. |
| Length | Short, 123.7 mm To be paired with CF-37.5/5.65+ tappets. Available in 32.5 and 33.0 mm nitrided stainless, and in 33.0 mm Inconel. |
Long, 125.0 or 126.1 mm To be paired with CF-37.5/3.1+ tappets and their shims. Available at the original size in Inconel, and in 32.5 and 33.0 mm nitrided stainless. |
When reinforced valves become necessary
- Cams with more lift or firmer valve springs
- Higher rev ceiling
- Turbo or supercharger conversion (Inconel preferred)
- Cylinder head rebuilt for track days, historic racing or rally
- Original valves marked, burnt or already reground
Vehicle compatibility
| Model | Engine code | Power | Years |
|---|---|---|---|
| M5 3.6 (E34) | S38B36 | 315 hp | 1988-1992 |
| M5 3.8 (E34) | S38B38 | 340 hp | 1992-1995 |
OEM part number (exhaust valve): 11 34 1 309 487 (S38B36)
Don't forget the inlet valves
An open S38 cylinder head is the time to change its inlet valves and its valve stem seals together. Here are the parts made for this six-cylinder engine:
| Inlet valves BMW M5 E34 S38B36 S38B38 → |
| Exhaust valve stem seals 7 mm BMW S38 → |
-
Brand
-
ReferenceBMEVN-1009-12