Skip to content
  • On order
Reinforced inlet valves FIAT Punto GT Turbo 176A4 Reinforced inlet valves FIAT Punto GT Turbo 176A4

Reinforced inlet valves FIAT Punto GT Turbo 176A4

€90.36 (tax incl.)
€112.94 (tax incl.) -20%

Set of 4 reinforced inlet valves for FIAT Punto GT Turbo 176A4.

  • Brand: FERREA
  • Engine: 176A4.000 1.4 8V turbo
  • Dimensions: 36 mm head, 8 mm stem, 108.52 mm long
  • Material: EV8 stainless steel, 3 grooves
F6769*4
0 in stock in France
ORDER TODAY, WE SHIP IN 15 DAYS
Pay in installments

FIAT engines covered

The 176A4.000 is the 1.4-litre 8-valve turbocharged four-cylinder engine of the first-series Fiat Punto GT, built from 1993 to 1997.

It has 4 inlet valves, original part number 7565812, with a 36 mm head and an 8 mm stem. More boost, a bigger turbo or a sharper camshaft load them far more than the factory setting.

FERREA reinforced inlet valves

On the Fiat Punto GT's 176A4.000, each cylinder has just one inlet valve: the cam presses it down to let through the turbo's charge, then it rises to snap onto its seat, the stem going back and forth in the guide every cycle. When the turbocharged 1.4 litre is driven hard, this movement repeats well over twenty times in a second. The part works between 400 and 550 °C, whereas a stock chrome-silicon steel, holding 500 MPa at 500 °C, keeps only 250 at 600 °C: half of its strength, 50 %, disappears at the first wave of heat, all the more so with raised boost.

The F6769*4 belongs to FERREA's 6000 series, which marries EV8 stainless steel with a stem coated in hard chrome. This metal maintains 650 MPa at 500 °C and 550 MPa at 600 °C, 30 % then 120 % more strength than chrome-silicon at the same temperatures, and that chrome finish keeps guide wear on the stem down. Offered at the 36 mm stock diameter, with an 8 mm stem and a 108.52 mm length, it goes into a head with sound seat faces, with no recut to a larger size.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
F6769*4 FERREA Standard 36 mm 8 mm 108.52 mm 3 EV8 stainless steel

Fitting details

PartFIAT originalReinforced
Collets
Valve stem seals
Valve guide 5 997 546

With its 3 grooves, the FERREA valve takes 3-groove collets; new collets are recommended.

At standard size, the 4 inlet seats simply need lapping if they are in good condition.

Technical guide

The brand offered

FERREA FERREA Racing Components settled in 1978 in Fort Lauderdale, Florida, and shapes each of its valves from one-piece forged bar stock, then machined in full on numerical equipment. Its output is found on NASCAR grids as well as in drag racing.

How to choose

The groove is the recess cut at the stem end, onto which the collets lock the retainer. For the 176A4, a single valve is offered:

CriterionOption 1Option 2
Size Standard size
36 mm head, when the head's inlet seat faces are still at stock diameter.
Grooves 3 grooves
Fitted with three-groove collets, preferably new, suited to road use as well as moderate tuning.

When reinforced valves become necessary

  • More boost or a bigger turbocharger
  • Pointier cam or springs rated higher
  • Ignition cut-off set higher than stock
  • Punto GT entered on track, hill climbs or rallies
  • Marked factory valves or reground seat faces

Compatible vehicles

ModelEngine codePowerYears
Punto (176) 1.4 GT Turbo 176A4.000 1993-1997

OEM part number (inlet valve): 7565812

Important: a set of 4 covers a complete engine. The other Fiat 1.4 turbo engines (146A8 of the Uno Turbo, 176B6 of the later Punto GT) are not covered by this page.

Related products

While the 176A4 head is off, also replace its 4 exhaust valves, which we likewise stock in reinforced form; follow the link given below:

FIAT Punto GT Turbo Uno Turbo 1.4 exhaust valves →

7 other products in the same category

Viewed products

Loading...