Skip to content
  • On order
Reinforced inlet valves BMW M5 E34 S38B36 S38B38 Reinforced inlet valves BMW M5 E34 S38B36 S38B38

Reinforced inlet valves BMW M5 E34 S38B36 S38B38

€389.85 (tax incl.)
€487.31 (tax incl.) -20%

Set of 12 reinforced inlet valves for BMW M5 E34 S38B36 and S38B38.

  • Brand: SUPERTECH
  • Engines: S38B36, S38B38
  • Dimensions: 37.0 mm, 38.0 mm, 38.5 mm or 39.0 mm head, 7 mm stem
  • Material: black nitride stainless steel, 3 grooves
BMIVN-1006L-12
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

BMW engines covered

The S38 is the 24-valve inline six-cylinder of the BMW M5 E34, with twin overhead camshafts and solid tappets with shims. The 3.6 litre S38B36 (3,535 cc, 315 hp) powers the saloon from 1988 to 1992; the 3.8 litre S38B38 (3,795 cc, 340 hp) takes over until 1995, in saloon and Touring form.

The engine has 12 inlet valves with a 7 mm stem. The S38B36 valve, BMW part 11 34 1 309 343, has a 37.0 mm head, a 7.0 mm stem and a length of 121.4 mm; the S38B38 moves to 11 34 1 315 508, with a 38.5 mm head. Both are held by 3-groove collets 11 34 1 307 136. They are fine for the standard engine, but a tune that adds lift, spring stiffness or revs pushes them beyond their margin.

SUPERTECH reinforced inlet valves

When the engine revs hard, each inlet valve opens and shuts off the fresh air charge a number of times counted in tens every second. Each time, the head strikes its seat in the cylinder head again, and all the while the stem shuttles to and fro in the guide. Working temperature sits between 400 and 550 °C, and that is already where the factory chrome-silicon steel gives ground: 500 MPa at 500 °C, then 250 MPa around 600 °C, just past that window, a drop of 50 %. Raising cam lift, spring stiffness, maximum rpm or boost pressure each add impacts, friction and heat that wear the part out.

SUPERTECH forges these reinforced valves from a chrome-nickel stainless steel reserved for racing, from the same family as EV8 (21-4N). It still holds 650 MPa at 500 °C, 30 % above the factory steel, and 550 MPa at 600 °C, 120 % above. The black nitride treatment makes the surface harder and smoother, so the stem wears less and runs more gently against the guide.

They come in the standard size, a 37.0 mm head, and in three oversizes: 38.0 mm (+1 mm), 38.5 mm (+1.5 mm) and 39.0 mm (+2 mm). The stem diameter does not move, it stays at 7 mm; only the head gets bigger. Its seat then lets a wider flow through, more air reaches the cylinder and output rises, as long as the seats are machined to match. Each oversize comes in 121.4 mm overall length, the original figure, or in 123.8 mm; the standard size version is 123.0 mm.

Inlet valve technical specification

Part numberBrandSizeHead Ø
OEM 37.0 mm
Stem Ø
OEM 7 mm
Length
OEM 121.4 mm
GroovesMaterial
BMIVN-1006L-12 SUPERTECH Standard 37.0 mm 7 mm 123.0 mm 3 Black nitride stainless steel
BMIVN-1008-12 SUPERTECH +1 mm 38.0 mm 7 mm 121.4 mm 3 Black nitride stainless steel
BMIVN-1009-12 SUPERTECH +1.5 mm 38.5 mm 7 mm 121.4 mm 3 Black nitride stainless steel
BMIVN-1009L-12 SUPERTECH +1.5 mm 38.5 mm 7 mm 123.8 mm 3 Black nitride stainless steel
BMIVN-1010-12 SUPERTECH +2 mm 39.0 mm 7 mm 121.4 mm 3 Black nitride stainless steel
BMIVN-1010L-12 SUPERTECH +2 mm 39.0 mm 7 mm 123.8 mm 3 Black nitride stainless steel

S38B38: original inlet valve with a 38.5 mm head (11 34 1 315 508).

Fitting details

PartBMW originalReinforced
Collets 11 34 1 307 136 (3 grooves)
Valve stem seals Kit 11 34 9 059 172 VS-VW7I-12 (inlet)
Valve guide Inner Ø 7.0 mm H7 GDE-BMS14-7

With 3 grooves like the BMW valves, these valves fit with 7 mm 3-groove collets, ideally new.

For the +1, +1.5 and +2 mm sizes, the inlet seats of the cylinder head are recut to the new dimension during the rebuild.

The S38 has solid tappets with shims: after changing the valves, check the clearance and adjust the shims.

Technical guide

The brand offered

SUPERTECH SUPERTECH has spent more than 30 years in San Jose, California, developing valvetrain components built for racing. Its valves are drawn one by one for the engine they target, examined by ultrasound, X-ray and laser gauging, then signed off by tuners, whether for drag racing or circuit work.

How to choose

Under the retainer, the collets lock into the groove to hold the valve. All parts here have 3 grooves, like the BMW layout: only the size is to be chosen.

CriterionOption 1Option 2
Size Standard size
37.0 mm head, the same as the production S38B36: suits inlet seats that were never reground and are still at factory size.
+1 to +2 mm oversize
38.0, 38.5 or 39.0 mm heads: a wider seat lets more air in, hence more power (about 10 to 12 cfm per mm of head). Seat machining to the larger size is required, best paired with opened-up ports; also a sound option when the seats were reground earlier.

When reinforced valves become necessary

  • Higher cam lift or stiffer springs fitted
  • Rev limit pushed higher
  • Turbocharger or supercharger added
  • Head build for circuit, rally or drift use
  • Production valves worn, marked or already recut to repair size

Compatible vehicles

ModelEngine codePowerYears
M5 (E34) 3.6 S38B36 315 hp 1988-1992
M5 (E34) 3.8 S38B38 340 hp 1992-1995
M5 Touring (E34) 3.8 S38B38 340 hp 1992-1995

OEM part number (inlet valve): 11 34 1 309 343 (S38B36) ; 11 34 1 315 508 (S38B38)

Important: these sets of 12 are intended for the S38 six-cylinder; the S14 four-cylinder of the M3 E30 takes sets of 8, offered on a separate page.

Related products

Rebuilding an S38 head usually means fitting new exhaust valves as well, together with brand new valve stem seals. Matching parts for this engine:

BMW M5 E34 S38B36 S38B38 exhaust valves →
7 mm inlet valve stem seals →

10 other products in the same category

Viewed products

Loading...