Skip to content
  • In stock
BMW E36 325i M50B25 192cv 09/1990-09/1995 Joint de culasse renforcé ATHENA BMW E36 325i M50B25 192cv 09/1990-09/1995 Joint de culasse renforcé ATHENA

SUPERTECH inlet valve stem seals BMW S38 S50B30

€11.27 (tax incl.)
€14.09 (tax incl.) -20%

Set of 12 inlet valve stem seals for BMW S38 and European S50B30, 7 mm stem.

  • Brand: SUPERTECH
  • Engines: S38B35, S38B36, S38B38, S50B30 (306S1)
  • Material: Polyacrylate (ACM)
VS-VW7I-12
2 in stock in France
Pay in installments

BMW engines concerned

This set fits the inlet side of two 24-valve BMW M six-cylinders with 7 mm stems: the S38 of the M 635 CSi (E24) and M5 (E28 and E34), in B35, B36 and B38 sizes, from 1984 to 1995, and the European S50B30 (306S1) of the E36 M3 3.0, coupé, saloon and convertible, M3-R included, from 1992 to 1995.

Each engine takes twelve inlet valves, two per cylinder. BMW fits them from the factory with seal set 11 34 9 059 172; each seal caps its guide and only lets down the oil that lubricates the stem.

SUPERTECH inlet valve stem seals

On a high-revving S38 or S50, the inlet stem seal meters oil precisely: too little and the stem seizes in its guide, too much and the oil is burnt in the chamber. Once aged, shrunk or split it lets the excess through: falling level, a blue haze at the first start of the day or when lifting off, carbon on valves and plugs.

For the inlet side SUPERTECH uses polyacrylate (ACM), a robust elastomer, fitted on a guide with a 9.8 mm outside diameter around a 7 mm stem. The set of 12 covers the full inlet of the six-cylinder; the exhaust, where temperatures climb higher, needs a high-temperature Viton, sold separately.

Stem seal technical specifications

Part numberBrandPositionMaterialStem ØGuide ØSeal outside Ø
VS-VW7I-12 SUPERTECH Inlet Polyacrylate (ACM) 7 mm 9.8 mm 13.2 mm

Stem seal installation

PartOriginalReinforced
Inlet stem seal 11 34 9 059 172 Replaced by this set
Exhaust stem seal 11 34 9 059 172 VS-VW7E-12
Valves 7 mm stem Inlet: S38 / S50B30
Exhaust: S38 / S50B30

Technical guide

The brand offered

SUPERTECH SUPERTECH was created in San Jose, California, and has drawn racing valves, springs and seals for over 30 years, for BMW six-cylinders as for many other engines. Every batch goes through ultrasound, laser and X-ray checks before leading engine builders approve it.

Inlet or exhaust?

On these BMW six-cylinders, inlet and exhaust seals are identical in size, but their rubber differs: polyacrylate (ACM) for VS-VW7-I at the inlet, Viton (FKM) for VS-VW7-E at the exhaust, which sees more heat. SUPERTECH quotes 177 °C (350 °F) for polyacrylate and 204 °C (400 °F) continuous for Viton. Twelve of each go into every engine.

When valve stem seals must be replaced

  • Oil level falling, blue smoke from the S38 or S50 six
  • Cylinder head taken off for an overhaul
  • New valve guides fitted
  • Uprated valves or springs planned

Vehicle compatibility

BMW

ModelEngine codePowerYears
M 635 CSi (E24) S38 B35 286 hp 1984-1988
M 635 CSi (E24) S38 B35 260 hp 1986-1989
M5 (E28) S38 B35 286 hp 1985-1987
M5 (E28) S38 B35 260 hp 1986-1987
M5 (E34) S38 B36 315 hp 1988-1992
M5 (E34) S38 B38 340 hp 1992-1995
M5 Touring (E34) S38 B38 340 hp 1992-1995
M3 Coupé (E36) 3.0 S50 B30 (306S1) 286 hp 1992-1995
M3 Coupé (E36) 3.0 S50 B30 (306S1) 295 hp 1993-1995
M3 (E36) 3.0 S50 B30 (306S1) 286 hp 1994-1995
M3 Cabriolet (E36) 3.0 S50 B30 (306S1) 286 hp 1994-1995
M3-R Coupé (E36) 3.0 S50 B30 (306S1) 329 hp 1994-1995

OEM part number (BMW stem seal set): 11 34 9 059 172

Important: the S50B30 of the North American E36 M3 (306S2), with 6 mm stems, is not covered by this set.

Remember the exhaust valve stem seals

The exhaust seals age too: with the head already off, replace them in the same job. For the S38 and S50B30, SUPERTECH offers:

BMW S38 S50B30 exhaust stem seals →

11 other products in the same category

Loading...