Skip to content
  • On order
Reinforced inlet valves NISSAN Pulsar GTI-R SR20DET Reinforced inlet valves NISSAN Pulsar GTI-R SR20DET

Reinforced inlet valves NISSAN Pulsar GTI-R SR20DET

€211.53 (tax incl.)
€264.41 (tax incl.) -20%

Set of 8 reinforced inlet valves for the NISSAN Pulsar GTI-R (RNN14) with the SR20DET engine.

  • Brand: SUPERTECH
  • Engines: SR20DET
  • Dimensions: 35.15 mm head, 5.97 mm stem, 102.10 mm length
  • Material: black nitride stainless steel
NIVN-1007-GTIR-8
On order, 15 to 30 days lead time
Pay in installments

NISSAN engines covered

The Pulsar GTI-R RNN14 gets its own version of the SR20DET, Nissan's 2.0 litre 16-valve four-cylinder with twin overhead camshafts and a turbo, fitted to this four-wheel-drive compact.

The engine has 8 inlet valves, two per cylinder. Raised boost, sharper camshafts or a higher rev limit load them well beyond stock use.

SUPERTECH reinforced inlet valves

In the Pulsar GTI-R's SR20DET, each inlet valve takes the air pushed by the turbo, lets it into the cylinder and then closes the port, over and over, cycle after cycle, by the dozen every second as the needle climbs. Every closing ends with the head hitting the seat face, while the stem keeps sliding in its guide. The part works between 400 and 550 °C, a zone where factory chrome-silicon is already losing ground: from 500 MPa at 500 °C it drops to 250 MPa near 600 °C, just above, meaning 50 % less strength. Pumping up boost, lengthening lift, revving higher or rating the springs harder all multiply shocks, friction and temperature rise.

For these reinforced valves SUPERTECH uses a chrome-nickel stainless steel designed for competition, close to EV8 (21-4N): 650 MPa at 500 °C and 550 MPa at 600 °C, i.e. a 30 % then 120 % margin over production steel. Thanks to black nitriding, the stem gains hardness and polish, which spares the guide and clearly slows rubbing wear.

The NIVN-1007-GTIR-8 comes in +1 mm oversize: 35.15 mm head, 5.97 mm stem, 102.10 mm overall length and a single groove. With its enlarged head the seat passage increases, the cylinder fills more fully and the engine finds extra power, on condition that the inlet seats get machined for this new size.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
NIVN-1007-GTIR-8 SUPERTECH +1 mm 35.15 mm 5.97 mm 102.10 mm 1 Black nitride stainless steel

Fitting details

PartNISSAN originalReinforced
Collets KPR-6N-6-ST-24
Valve stem seals VS-N6I-12
Valve guide

The +1 mm size requires the inlet seats to be cut to 35.15 mm, workshop work to plan with the cylinder head rebuild.

Technical guide

The brand offered

SUPERTECH SUPERTECH has spent more than 30 years in San Jose (California) designing valvetrains for competition engines. Each part number there is built around a precise cylinder head; ultrasound, radiography and laser check it before tuners approve it, for drag strips and race tracks alike.

When reinforced valves become necessary

  • Sharper cam, valve springs rated harder
  • Rev limit moved upwards
  • More boost pressure or a larger turbo
  • Head honed for track, hillclimb or rally
  • Production valves damaged, tired or already reworked

Compatible vehicles

ModelEngine codePowerYears
Pulsar GTI-R (RNN14) SR20DET 220-230 hp 1990-1995
Important: this page only covers the SR20DET of the Pulsar GTI-R; the SR20DET of the 180SX, 200SX and Silvia and the other SR20 engines are not included.

Related products

For a rebuilt Pulsar GTI-R SR20DET head, it makes sense to replace the exhaust valves as well. Our reinforced versions are shown on this page:

NISSAN Pulsar GTI-R SR20DET exhaust valves →

16 other products in the same category

Viewed products

Loading...