Skip to content
  • In stock
Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R

Tri-metal crankshaft main bearings ACL Nissan SR20DET GTi-R

€108.67 (tax incl.)
€120.74 (tax incl.) -10%

Set of tri-metal crankshaft half shells for the five main bearings of the Nissan SR20DET GTi-R four-cylinder engine.

  • Brand and coating: ACL Race, no coating or Calico
  • Fits: Nissan Sunny GTI-R (N14)
  • Engine codes: SR20DET
  • Sizes available: standard to +0.25 mm, increased clearance version (HX); Calico: standard and HXC
5M2975H-STD
2 in stock in France
On order, 15 to 30 days lead time
Available in stock in France
Pay in installments

The Nissan SR20DET GTi-R four-cylinder engine

The SR20DET GTi-R is the Nissan 2.0 litre four-cylinder with twin overhead camshafts, 16 valves and a turbocharger, fitted to the four-wheel-drive Nissan Sunny GTI-R (N14). ACL lists a main bearing set for it. Its crankshaft runs on five main bearings.

The crankshaft of this engine runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series tri-metal set shown here replaces them on built engines.

From the factory, Nissan fits these engines with main bearings under part number 12207-60J00, and its workshop manual specifies a running clearance of 0.004 to 0.022 mm.

Tri-metal main bearings

In a trimetal bearing, a steel back carries a copper-lead intermediate layer with high load capacity, itself covered by an anti-friction running layer that spares the main journal. The set is supplied complete: 0 half shells, i.e. The complete set covers the five main bearings of the crankshaft. The upper and lower half shells are different: each goes in its own position.

Trimetal targets high, sustained loads, whereas aluminium bi-metal is limited to low to medium loads: about 8,000 psi for the latter, up to 12,000 psi for a performance trimetal, 50% more. The benefit shows in strength and durability on turbo, supercharged and high-revving engines.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankshaft journal Ø 54.956 / 54.980 mm
Housing bore Ø 58.944 / 58.968 mm
Width 19.1 mm

Manufacturer's note (ACL 5M2975H): suits GTiR engines.

ReferenceBrand and treatmentSizeWall thickness (mm)
5M2975H-STD ACL Race - Untreated Standard 1.98
5M2975HX-STD ACL Race - Untreated Std, increased clearance (HX) 1.967
5M2975H-.025 ACL Race - Untreated +0.025 1.9925
5M2975H-.25 ACL Race - Untreated +0.25 2.105
5M2975HC-STD ACL Race - Calico Standard
5M2975HXC-STD ACL Race - Calico Std, increased clearance (HX)

Running clearance

Running clearance is the gap between the bearing and the main journal, filled by the oil film.

While the engine turns, the main journal floats on this oil film, which carries the load without direct contact with the bearing. Film thickness depends on clearance: too tight, oil passes poorly, temperature rises and the risk of seizure grows; too wide, oil escapes, the film carries less and oil pressure decreases. A correct clearance ensures both sufficient lubrication and a well-maintained film.

Size / gradeWhen to choose itACL Race Series
Standard (STD) Standard journal, not reground 0.057 to 0.068 mm
Increased clearance (HX) Wider clearance: high oil flow, high rpm 0.082 to 0.093 mm
+0.025 mm Polished journal 0.057 to 0.068 mm
+0.25 mm Journal reground to 0.25 mm 0.057 to 0.068 mm

Checking on assembly: lay a calibrated strip (Plastigauge) on the journal, torque the main cap to spec, then compare the crushed strip against the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

These ACL trimetal main bearings are aimed at built engines and racing: where a standard bearing quickly reaches its limit, they accept more power, more rpm and more boost. The range includes the standard size, a +0.025 mm size for a main journal that has only been polished, a +0.25 mm regrind size and the HX version with increased clearance for high-revving engines or engines needing a high oil flow. It allows the same part number to be kept after the crankshaft is reground and the clearance to be tailored to the oil used and the engine's duty.

The brand

ACL Bearing Company An Australian specialist in high-performance engine bearings since 1949, ACL Bearing Company produces the Race Series: precisely made trimetal bearings, available in numerous sizes and recognised on built engines across the world.

Vehicle compatibility

This main bearing set fits the Nissan SR20DET GTi-R four-cylinder engine of the following vehicle:

BrandModel (chassis)Engine codePowerYears
NISSAN SUNNY III Hatchback (N14) 2.0 GTI-R 4x4 SR20DET 220–230 hp 1990–1995

Why replace the bearings

Replacing the bearings during a build or rebuild guards against the most expensive failure: a worn-out main bearing scores the main journal, contaminates the oil circuit with debris and forces at least a crankshaft regrind, or even block repairs. Against such costs a new set weighs little: it is the cheapest part of the crankshaft assembly, but the one whose failure costs the most.

16 other products in the same category

Viewed products

Loading...