- In stock
Tri-metal crankshaft main bearings Nissan SR20DE SR20DET
Set of 10 tri-metal crankshaft main bearing shells for Nissan SR20DE and SR20DET.
- Brands and treatments : ACL Race (with or without Calico) and King Racing (XP and XPC)
- Compatibility : 180SX, 200SX, Silvia, Primera, Sunny, Serena, Bluebird, Almera (partial list)
- Available sizes : standard to +0.50 mm, increased clearance versions (HX / STDX)
The Nissan SR20DE and SR20DET four-cylinder engines
The SR20DE and SR20DET are the Nissan 2.0 litre four-cylinder engines with twin overhead camshafts and 16 valves, the latter turbocharged. They power the Nissan 180SX, 200SX, Silvia, Primera, Sunny, Serena and Bluebird, among others. ACL and King list a main bearing set for these engines.
The crankshaft of these engines runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series and KING RACING tri-metal sets shown here replace them on built engines.
From the factory, Nissan fits these engines with main bearings under part number 12207-60J00, and its workshop manual specifies a running clearance of 0.004 to 0.022 mm.
Tri-metal main bearings
A trimetal bearing combines three layers with complementary roles: a steel back that provides structural strength, a copper-lead intermediate layer that takes the heavy loads and an anti-friction running layer that protects the main journal. The complete set contains 0 half shells, i.e. The complete set contains 10 half shells, five pairs for five main bearings. The upper and lower half shells are different: each goes in its own position.
An aluminium bi-metal bearing, intended for low to medium loads, tops out at around 8,000 psi; a performance trimetal bearing holds up to 12,000 psi, 50% more load capacity. It therefore gains strength and service life on turbocharged, supercharged or high-revving engines.
Technical specifications
| ACL bearings Crankshaft journal Ø 54.956 / 54.980 mm Housing bore Ø 58.944 / 58.968 mm Width 19.1 mm | King bearings Crankshaft journal Ø 54.955 / 54.981 mm Housing bore Ø 58.943 / 58.969 mm Width 19 mm |
| Reference | Brand and treatment | Size | Wall thickness (mm) |
|---|---|---|---|
| 5M2964H-STD | ACL Race - Untreated | Standard | 1.975 |
| 5M2964HX-STD | ACL Race - Untreated | Std, increased clearance (HX) | 1.962 |
| 5M2964H-.025 | ACL Race - Untreated | +0.025 | 1.9875 |
| 5M2964H-.25 | ACL Race - Untreated | +0.25 | 2.1 |
| 5M2964H-.50 | ACL Race - Untreated | +0.50 | 2.225 |
| 5M2964HC-STD | ACL Race - Calico | Standard | |
| 5M2964HXC-STD | ACL Race - Calico | Std, increased clearance (HX) | |
| 5M2964HC-.025 | ACL Race - Calico | +0.025 | |
| 5M2964HC-.25 | ACL Race - Calico | +0.25 | |
| MB5243XP | King Racing - Untreated | Standard | 1.975 |
| MB5243XP STDX | King Racing - Untreated | Std, increased clearance (STDX) | 1.962 |
| MB5243XP0.25 | King Racing - Untreated | +0.25 | 2.102 |
| MB5243XP0.5 | King Racing - Untreated | +0.50 | 2.229 |
| MB5243XPC | King Racing - pMaxKote | Standard | 1.975 |
| MB5243XPC STDX | King Racing - pMaxKote | Std, increased clearance (STDX) | 1.962 |
| MB5243XPC.026 | King Racing - pMaxKote | +0.026 | 1.988 |
| MB5243XPC0.25 | King Racing - pMaxKote | +0.25 | 2.102 |
Running clearance
Running clearance is the space left between the bearing and the main journal, permanently filled by the oil film.
With the engine running, the main journal does not touch the bearing: it rides on this oil film, which takes the load. The clearance sets the film thickness. Too small, it restricts oil flow, raises the temperature and invites seizure; too large, it lets the oil escape, the film loses its load capacity and oil pressure falls. The right clearance combines sufficient lubrication with an oil film that keeps carrying the load.
| Size / grade | When to choose it | ACL Race Series | King XP and XPC |
|---|---|---|---|
| Standard (STD) | Standard journal, not reground | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
| Increased clearance (HX / STDX) | Wider clearance: high oil flow, high rpm | 0.082 to 0.093 mm | 0.080 mm - 0.093 mm |
| +0.025 / +0.026 mm | Polished journal | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
| +0.25 mm | Journal reground to 0.25 mm | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
| +0.50 mm | Journal reground to 0.50 mm | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
Check at assembly: lay a calibrated strip (Plastigauge) on the journal, tighten the main cap following the manufacturer's procedure, then compare the width of the crushed strip with the gauge to read the clearance.

Technical guide
The ACL and King main bearings shown here are trimetal bearings built for engine tuning and racing. They withstand far higher loads than a standard bearing and come in several sizes: the standard size, a +0.025 / +0.026 mm size for a main journal that has only been polished, +0.25 and +0.50 mm regrind sizes and the HX / STDX version with increased clearance for high-revving engines or engines needing a high oil flow. This range lets you refit a reground crankshaft without changing product line and match the clearance to the oil and use chosen.
The two brands
![]() |
Founded in Australia in 1949, ACL Bearing Company designs high-performance engine bearings. Its Race Series brings together precision trimetal bearings, offered in a wide choice of sizes and fitted to built engines around the world. |
![]() |
King Engine Bearings, an Israeli manufacturer of high-performance engine bearings since the 1960s, offers with its pMax Black tri-metal alloy bearings designed for heavy loads, with a pMaxKote coating (XPC version). |
Construction and advantages
| Criterion | ACL Race Series | King Racing |
| Cross-section | ![]() |
![]() |
| Type | High-performance trimetal bearing | High-performance trimetal bearing |
| Country of manufacture | Australia | Israel |
| Construction | Trimetal: steel back, copper layer, soft surface | Trimetal: steel back, copper layer, soft surface |
| Alloy | Race Series (copper-lead) | pMax Black (hardened copper-lead) |
| Protective coating | Calico CT-1 (HC and HXC versions): thin dry-film lubricant that reduces friction and wear. No coating on the H and HX versions. | pMaxKote (XPC version): polymer coating on the surface that limits wear when lubrication drops (start-ups, thin oil film). The XP version has no coating. |
| Available sizes | Standard to +0.50 mm (+ increased clearance HX) ; Calico: standard, HXC and +0.25 mm | Standard to +0.50 mm (+ increased clearance STDX) ; XPC: standard, STDX and +0.25 mm |
Vehicle compatibility
This main bearing set fits the Nissan SR20DE and SR20DET four-cylinder engines of the following vehicles:
| Brand | Model (chassis) | Engine code | Power | Years |
|---|---|---|---|---|
| NISSAN | SUNNY III Hatchback (N14) 2.0 GTI 16V | SR20DE | 143 hp | 1990–1995 |
| NISSAN | PRIMERA (P10) 2.0 GT / 2.0 i / 2.0 / 2.0 GT 4x4 (HNP10) / 2.0 4x4 | SR20DE | 125–150 hp | 1990–1996 |
| NISSAN | 100NX (B13) 2.0 GTI / 2.0 | SR20DE | 143–150 hp | 1990–1994 |
| NISSAN | SERENA (C23) 2.0 / 2.0 (KBC23) / 2.0 4WD (KBNC23) | SR20DE | 126–130 hp | 1992–2001 |
| NISSAN | 200SX Coupé (S14) 2.0 i 16V Turbo / 2.0 Turbo | SR20DET | 200–220 hp | 1993–2000 |
| NISSAN | PRIMERA Hatchback (P10) 2.0 i / 2.0 / 2.0 GT 4x4 | SR20DE | 125–152 hp | 1990–1996 |
| NISSAN | ALMERA I Hatchback (N15) 2.0 GTi | SR20DE | 143 hp | 1996–2000 |
| NISSAN | PRIMERA (P11) 2.0 16V | SR20DE | 115–150 hp | 1996–2001 |
| NISSAN | PRIMERA Hatchback (P11) 2.0 16V | SR20DE | 115–150 hp | 1996–2002 |
| NISSAN | PRIMERA Traveller (WP11) 2.0 16V | SR20DE | 115–140 hp | 1996–2001 |
| NISSAN | SUNNY III Liftback (N14) 2.0 i 16V | SR20DE | 143 hp | 1990–1995 |
| NISSAN | ALMERA TINO (V10) 2.0 | SR20DE | 136 hp | 2000–2003 |
| NISSAN | 200SX Coupé (S14) 2.0 i 16V / 2.0 | SR20DE | 141–162 hp | 1993–1999 |
| NISSAN | 200SX (S13) 2.0 i 16V | SR20DE | 140 hp | 1988–1993 |
| NISSAN | PRIMERA Traveller (W10) 2.0 | SR20DE | 150 hp | 1994–1998 |
| NISSAN | SERENA (C24) 2.0 SGX (PC24) / 2.0 SGX 4x4 (PNC24) | SR20DE | 145 hp | 1999–2005 |
| NISSAN | AD Van (Y10) 2.0 | SR20DE | 125 hp | 1994–1999 |
| NISSAN | ALMERA II Hatchback (N16) 2.0 | SR20DE | 145 hp | 2002–9999 |
| NISSAN | ALMERA II (N16) 2.0 | SR20DE | 145 hp | 2002–9999 |
| NISSAN | SENTRA V (B15) 2.0 | SR20DE | 145–150 hp | 2000–2006 |
| NISSAN | AVENIR (W11) 2.0 / 2.0 4x4 | SR20DE | 140–145 hp | 1997–2006 |
| NISSAN | BLUEBIRD SYLPHY I (G10, N16) 2.0 | SR20DE | 145 hp | 2000–2006 |
| NISSAN | PICK UP (D22) 2.0 | SR20DE | 125 hp | 1997–2001 |
| NISSAN | 180SX Coupé (S13) 2.0 Turbo | SR20DET | 200–208 hp | 1991–1997 |
| NISSAN | CIMA (Y33) 2.0 | SR20DE | 145 hp | 1996–2001 |
| NISSAN | EXPERT I (W10) 2.0 | SR20DE | 126 hp | 1995–2000 |
| NISSAN | BLUEBIRD (U13, U14) 2.0 / 2.0 AWD | SR20DE | 145 hp | 1991–2001 |
| NISSAN | TSURU 2.0 | SR20DE | 141 hp | 1991–2007 |
| NISSAN | SUNNY III (N14, B13) 2.0 | SR20DE | 141–143 hp | 1990–1996 |
| NISSAN | SUNNY IV Saloon (N16) 2.0 | SR20DE | 125–150 hp | 1997–2002 |
| NISSAN | LUCINO Hatchback (N15) 2.0 | SR20DE | 143 hp | 1995–2000 |
| NISSAN | LUCINO Hatchback (N14) 2.0 | SR20DE | 143 hp | 1991–1994 |
| NISSAN | LUCINO Hatchback (N14) 2.0 | SR20DET | 220 hp | 1991–1995 |
| NISSAN | LUCINO Saloon (B14) 2.0 GTi | SR20DE | 143 hp | 1995–2000 |
| NISSAN | SILVIA (S15) Turbo 16V / 2000 Turbo | SR20DET | 200–250 hp | 1999–2003 |
| NISSAN | 180SX Coupé (S13) 2.0 | SR20DE | 162 hp | 1991–1994 |
| NISSAN | BLUEBIRD (U13, U14) 2000 SSS Turbo 2.0 AWD (HNU13) | SR20DET | 210 hp | 1991–1996 |
| NISSAN | SUNNY III Coupé 2.0 | SR20DE | 141 hp | 1995–1997 |
| NISSAN | ALMERA I (N15) 2.0 | SR20DE | 125 hp | 1995–2000 |
| NISSAN | PRESEA (R11) 2.0 | SR20DE | 145 hp | 1997–2000 |
| NISSAN | AVENIR (W11) 2.0 Turbo 4x4 | SR20DET | 200 hp | 1998–2005 |
| NISSAN | SENTRA III (B13) 2.0 | SR20DE | 143 hp | 1992–1994 |
| NISSAN | PRAIRIE LIBERTY (_M12) 2.0 (PM12) / 2.0 4WD (PNM12) | SR20DE | 140 hp | 1998–2001 |
| NISSAN | PRAIRIE LIBERTY (_M12) 2.0 GT4 4WD (PNM12) | SR20DET | 230 hp | 1998–2001 |
| NISSAN | SILVIA (S15) 2000 | SR20DE | 160–165 hp | 1999–2002 |
| NISSAN | ALTRA Estate (N30) 2.0 | SR20DE | 140 hp | 1997–2001 |
| NISSAN | ALTRA Estate (N30) 2.0 | SR20DET | 200 hp | 1997–2001 |
| NISSAN | PRAIRIE PRO (M11) 2.0 (PM11) / 2.0 4x4 (PNM11) | SR20DE | 145 hp | 1995–1998 |
| NISSAN | R'NESSA (N30) 2.0 Turbo 4WD (NN30) | SR20DET | 200 hp | 1997–2001 |
| NISSAN | R'NESSA (N30) 2.0 (N30) | SR20DE | 140 hp | 1997–2001 |
| NISSAN | BLUEBIRD (U14) 2.0 / 2.0 AWD | SR20DE | 145 hp | 1996–2002 |
| NISSAN | SILVIA Coupé (S13) 2.0 | SR20DET | 205–223 hp | 1991–1993 |
| NISSAN | SILVIA Coupé (S13) 2.0 | SR20DE | 140 hp | 1991–1993 |
| NISSAN | SILVIA Convertible (S15) 2.0 | SR20DE | 160–165 hp | 2000–2001 |
| NISSAN | AVENIR (W10) 2.0 (PW10) | SR20DE | 140 hp | 1990–1997 |
| NISSAN | SENTRA II (ES, N14) 200i | SR20DE | 143 hp | 1992–2002 |
| NISSAN | SABRE (ES, N14) 200i | SR20DE | 140 hp | 1994–2001 |
| NISSAN | 200SX Coupé (S15) i 16V Turbo | SR20DET | 200 hp | 2000–2002 |
Why replace the bearings
A failing main bearing does not fail alone: it scores the main journal, sends debris through the oil circuit and calls at least for a crankshaft regrind, when it does not damage the block as well. On a built engine, a bearing set costs only a fraction of a regrind, and even less of a full rebuild: it is the cheapest part of the crankshaft assembly and the one whose failure costs the most.
-
Brand
-
Reference5M2964H-STD



