Skip to content
  • On order
Reinforced exhaust valves Nissan Pulsar GTI-R SR20DET Reinforced exhaust valves Nissan Pulsar GTI-R SR20DET

Reinforced exhaust valves Nissan Pulsar GTI-R SR20DET

€393.12 (tax incl.)
€491.40 (tax incl.) -20%

Set of 8 reinforced exhaust valves for the Nissan Pulsar GTI-R.

  • Brand: SUPERTECH
  • Engine: SR20DET (Pulsar GTI-R RNN14)
  • Dimensions: 31.15 mm head (+1 mm), 6.94 mm stem
  • Material: Inconel
NEVI-1007-7GTIR-8
On order, 15 to 30 days lead time
Pay in installments

Nissan engines covered

The Pulsar GTI-R RNN14 has its own version of the SR20DET, Nissan's twin-cam 16-valve 2.0 turbo.

This engine has 8 exhaust valves, two per cylinder. The reinforced valves in this set have a 31.15 mm head, a 6.94 mm stem, a 103.0 mm overall length and a 7.25 mm tip.

SUPERTECH reinforced exhaust valves

The Pulsar GTI-R's SR20DET spreads its exhaust over eight valves, two per cylinder, through which flows gas already pushed by the turbo and loaded with the cycle's heat. In the metal, an exhaust valve head sits around 760 to 870 °C when there is no boost; on this turbocharged four-cylinder it passes the thousand-degree mark (1,000 °C). To cool down it only has its contact with the seat, which soaks up nearly 75 % of the heat, and the stem's travel through its guide, which removes about 20 %. Conventional steel copes badly with this: in the EV8 family, our yardstick, it falls back from 550 MPa near 600 °C to 300 MPa near 800 °C. Raised boost, long full-load runs or rallying, and the head ends up tiring, warping and leaking.

SUPERTECH makes the NEVI-1007-7GTIR-8 from Inconel; this nickel superalloy retains 860 MPa at 730 °C and 554 MPa near 815 °C, some 85 % better than EV8 steel at around 800 °C: the material that suits the GTI-R engine once its boost climbs. It keeps the 6.94 mm stem, the 103.0 mm overall length and one groove, designed for KPR-6N-6-ST-24 collets; the set of 8 equips the whole cylinder head.

It comes as a +1 mm oversize, with a 31.15 mm head: cylinder scavenging speeds up and filling improves, as long as every one of the 8 exhaust seats is recut to suit. A head that seats squarely also passes its heat on more evenly.

Exhaust valve technical specifications

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
NEVI-1007-7GTIR-8 SUPERTECH +1 mm 31.15 mm 6.94 mm 103.0 mm 1 Inconel

The NEVI-1007-7GTIR-8 differs from the NEVI-1032/7-L by a groove placed 1.65 mm higher and a length 0.3 mm shorter.

Valve fitting

PartNissan originalReinforced
Collets KPR-6N-6-ST-24 (1 groove)
Valve stem seals
Valve guide

Before reassembly, check that the collets match the groove of the NEVI-1007-7GTIR-8.

With a 31.15 mm head, the 8 exhaust seats are machined to the new size before fitting.

The 8 valves of the set share the same 6.94 mm stem, the same 103.0 mm length and the same 7.25 mm tip.

Technical guide

Our brand

SUPERTECH SUPERTECH, a Californian maker active for three decades, develops competition valves together with the parts that surround them: springs, titanium retainers, guides. In titanium, Inconel or stainless, every part is conceived for one precise engine and validated alongside seasoned tuners.

How to choose

The GTI-R's SR20DET takes only one SUPERTECH valve, already in Inconel and at +1 mm: the build is therefore judged on the health of the eight seats, then on the boost pressure the engine will have to hold.

CriterionOption 1Option 2
Seats Seats in good condition
Lightly marked seats machine without difficulty to the 31.15 mm diameter and give the head a continuous contact. Take the chance to check guide wear on the 6.94 mm stem and to fit new KPR-6N-6-ST-24 collets. Keep each valve paired with its own guide.
Heavily recut seats
If the head has already been recut several times, the workshop checks that enough material remains for the +1 mm oversize, changes the seat inserts if needed and laps each of the 8 valves onto its seat. Final lapping secures the seal.
Use Road and road rally
On a lightly modified GTI-R, Inconel offers a comfortable margin against turbo temperatures; replace the exhaust stem seals and confirm the fitting height spring by spring. Check guide clearance as well.
Raised boost or big turbo
When boost climbs or a larger turbo is fitted, Inconel becomes essential; pick springs sized for that lift and have the geometry of each guide checked before reassembly.

When reinforced valves become necessary

  • Raised boost on the GTI-R (Inconel version recommended)
  • Larger turbocharger with a revised engine map
  • More aggressive cam profiles, firmer valve springs
  • Rally stages, hill climbs or repeated track days
  • Cylinder head rebuild after marked exhaust valves

Vehicle compatibility

ModelEngine codePowerYears
Pulsar GTI-R (RNN14) SR20DET

OEM part number (exhaust valve):

Important: one set of 8 covers a complete engine. These valves are designed for the Pulsar GTI-R RNN14: the other SR20DET versions and the RB26DETT are not covered on this page.

Don't forget the inlet valves

A GTI-R SR20DET cylinder head open on the bench is the moment to review the inlet valves as well, so that all sixteen valves go back into service together:

Inlet valves Nissan Pulsar GTI-R SR20DET →

16 other products in the same category

Loading...