Skip to content
  • On order
Reinforced inlet valves TOYOTA 3S-GTE Reinforced inlet valves TOYOTA 3S-GTE

Reinforced inlet valves TOYOTA 3S-GTE

€209.77 (tax incl.)
€262.21 (tax incl.) -20%

Set of 8 reinforced inlet valves for TOYOTA 3S-GTE 2.0 Turbo (MR2 SW20, Celica GT-Four, Caldina).

  • Brand: SUPERTECH
  • Engines: 3S-GTE
  • Dimensions: 34.0 mm or 34.5 mm head, 5.98 mm stem
  • Material: black nitride stainless steel
TIVN-1011-8
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

TOYOTA engines covered

The 3S-GTE is Toyota's 2 litre 16-valve turbo four, from 185 to 261 hp depending on generation. It powers the MR2 SW20 from 1989 to 1999, the Celica GT-Four (T16, T18, T20) from 1987 to 1999 and the Caldina GT-T up to 2007.

The engine has 8 Toyota 13711-88361 (1987-1989) then 13711-88362 (1990-1995) inlet valves, with a 33.5 mm head and a 5.97 mm stem, held by 90913-03021 collets. Higher boost, sharper camshafts or a raised rev limit load them well beyond stock use.

SUPERTECH reinforced inlet valves

On the 3S-GTE, the cam presses on the bucket tappet at every turn of the shaft; each of the 8 inlet valves then opens to let in the charge compressed by the turbo, before dropping back onto its seat while sliding in its guide. At high revs this happens several dozen times in a single second. The valve runs between 400 and 550 °C; in that zone, a conventional chrome-silicon steel holds only 500 MPa at 500 °C, then 250 MPa at 600 °C, so half its strength, i.e. 50 %, is already gone.

SUPERTECH makes these valves from a racing stainless steel related to EV8. This alloy keeps 650 MPa at 500 °C and still 550 MPa at 600 °C: it beats the original steel by 30 % at the first temperature and by 120 % at the second. A black nitride treatment then hardens and polishes the outside of the stem, which grips less in its guide and loses less material as the miles go by.

Two oversizes are available: +0.5 mm, giving a 34.0 mm head, and +1 mm, giving a 34.5 mm head, against 33.5 mm originally. Both share a 5.98 mm stem and a 100.5 mm length. As the head grows, it opens a wider section at the seat: the cylinders receive more mixture and the engine gains a measure of extra power, provided the inlet seats are first machined to the chosen size.

Inlet valve technical specification

Part numberBrandSizeHead Ø
OEM 33.5 mm
Stem ØLengthGroovesMaterial
TIVN-1011-8 SUPERTECH +0.5 mm 34.0 mm 5.98 mm 100.5 mm 1 Black nitride stainless steel
TIVN-1012-8 SUPERTECH +1 mm 34.5 mm 5.98 mm 100.5 mm 1 Black nitride stainless steel

Fitting details

PartTOYOTA originalReinforced
Collets 90913-03021 KPR-6T-ST-32
Valve stem seals 90913-02062 / 90913-02085 / 90913-02090
Valve guide Inner Ø 6.000-6.018 mm

The +0.5 mm and +1 mm sizes require the inlet seats to be cut to 34.0 mm or 34.5 mm, workshop work to plan with the cylinder head rebuild.

Technical guide

The brand offered

SUPERTECH For more than three decades, SUPERTECH has shipped springs, retainers, guides and valves to competition engines from its Californian plant in San Jose. Each part starts from a specific cylinder head, goes through laser, X-ray and ultrasound checks, and is confirmed with engine builders.

How to choose

To pick between the two sizes, look at the wear of the seats in the head and at the airflow gain wanted: +0.5 mm is the moderate step, +1 mm goes further.

CriterionOption 1Option 2
Size +0.5 mm oversize
34.0 mm head: more air in (about 10 to 12 cfm per mm of head). Seats to be cut; also makes up for seats already reground.
+1 mm oversize
34.5 mm head, for a stronger filling gain; seats to be cut to this size.

When reinforced valves become necessary

  • Higher cam lift or stiffer valve springs
  • Turbo boost pressure raised
  • Red line pushed above stock
  • 3S-GTE head readied for track, rally or hillclimb use
  • Stock valves marked, worn or already reground

Compatible vehicles

ModelEngine codePowerYears
MR2 II (SW20) 2.0 Turbo 3S-GTE 225-245 hp 1989-1999
Celica (T16) GT-Four 2.0 Turbo 3S-GTE 193 hp 1987
Celica Coupé (T16) GT-Four 2.0 Turbo 3S-GTE 185 hp 1988-1989
Celica (T18) GT-Four 2.0 Turbo 3S-GTE 203-224 hp 1989-1994
Celica (T20) GT-Four 2.0 Turbo 3S-GTE 242-256 hp 1994-1999
Caldina (T21) 2.0 Turbo 3S-GTE 190-261 hp 1997-2002
Caldina (T24) 2.0 Turbo 3S-GTE 260 hp 2002-2007

OEM part number (inlet valve): 13711-88361 (1987-1989); 13711-88362 (1990-1995)

Important: these sets cover the 3S-GTE turbo; the naturally aspirated 3S-GE takes other valves and is not covered here.

Related products

If the 3S-GTE head is fully rebuilt, also replace its 8 exhaust valves and its springs: we offer both in a reinforced version, via the buttons below:

TOYOTA 3S-GTE exhaust valves →
TOYOTA 3S-GTE valve spring kit →

15 other products in the same category

Viewed products

Loading...