Skip to content
  • On order
Kits coupelle renforcé TU5J4 Kits coupelle renforcé TU5J4

Reinforced valve spring kit PSA EW10J4S

€368.64 (tax incl.)
€460.80 (tax incl.) -20%

Sixteen reinforced valve springs for the PSA 2.0 16V EW10J4S engine rated at 180 hp.

  • Brands: CATCAMS
  • Engines: EW10J4S (16V)
  • Springs: single
  • Contents: springs and upper retainers
PAC-S90015*16+99410/S*16
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

The EW10J4S engine of Citroën and Peugeot

The EW10J4S is the sporting version of the PSA 2.0 litre sixteen-valve engine, rated at 180 hp (177 hp in the 307) and fitted to the Citroën C4 VTS, the Peugeot 206 RC and the Peugeot 307 2.0 16V. With four valves per cylinder, one head takes 16 springs.

Lower spring seats and collets fitted at the factory stay in place: the kit brings only the springs and their upper retainers.

CATCAMS reinforced valve springs in a kit

Once the cam has opened the valve, the spring brings it back to its seat and holds it against the cam. At high rpm, valve, retainer and collets make up a moving mass that the standard spring controls badly: the valve floats, bounces and may strike the piston.

This CATCAMS kit combines 16 PAC-S90015 springs and 16 upper retainers 99410/S. It gives 294 N at the seat at 38.0 mm and 775 N at 13.0 mm of lift, with the original seats and collets kept.

Valve spring kit technical specification

Part numberBrandSpringsOuter / inner ØSeat pressureOpen pressureRateMax liftKit contents
PAC-S90015*16+99410/S*16 CATCAMS Single Outer 25.4 mm 294 N at 38.0 mm 775 N at 13.0 mm 16 springs, 16 upper retainers

Valve spring kit fitting details

PartPSA originalReinforced spring kit
Spring Kit specific: PAC-S90015 (CATCAMS)
Retainer Kit specific: 99410/S (CATCAMS)
Spring seat Original kept
Collets Original kept

The kit is made up of 16 single springs PAC-S90015 and 16 upper retainers 99410/S; the standard spring seats and collets remain on the cylinder head.

This is the gap measured between the lower seat and the upper retainer, valve shut; every load applies solely at its own height. When valve seats are ground back, the retainers drift apart and the load falls by the spring rate in newtons for each millimetre. Measure all 16 heights after machining, then check them against the table.

CATCAMS
Installed height 38.0 mm
Seat pressure at this height 294 N

Technical guide

Our brands

CATCAMS CATCAMS (Cat Cams N.V.), a Belgium-based firm, designs competition camshafts shipped across the globe. Its computer-controlled grinder cuts even inclined lobes, and the brand's springs are worked out alongside these shafts, which have already competed in the BTCC and Le Mans.

How to choose

A high load keeps the valve pressed on its cam as engine speed rises: it opens the way to a sharper camshaft, a higher rev limit or a turbo, without float. CATCAMS quotes 775 N at 13.0 mm of lift for this kit. Since maximum lift is not published, have CATCAMS approve the camshaft you plan to fit before you buy.

CriterionKey point
Choosing the pressure Only one load is offered: 294 N at the seat at 38.0 mm. To decide whether it suits, consider the camshaft profile, the target rpm and any turbo; do not ask for more load than needed, because excess wears cams and drive for no gain. CATCAMS does not publish the load of the original springs, so no percentage gain is claimed. Excessive load also adds friction throughout the valvetrain, which is why more is not better.
Single or double spring The kit is built on the single spring PAC-S90015 and the upper retainer 99410/S; no double spring is included. Each valve gets one spring, with no inner spring to plan for, and the upper retainers are delivered with it.

When reinforced springs become necessary

  • Camshaft with more lift or duration than stock
  • Rev limit raised after engine tuning
  • Turbo or supercharger fitted
  • Head reworked for track, drift or rally
  • Worn springs or valves floating near the red line

Compatible vehicles

ModelEngine codePowerYears
Citroën C4 VTS 2.0 16V EW10J4S 180 hp 2004-2010
Peugeot 206 RC EW10J4S 180 hp 2003-2007
Peugeot 307 2.0 16V EW10J4S 177 hp 2003-2009
Important: this kit is intended for the EW10J4S only. The other PSA engines, including the EW10J4, the EW10A, the TU and the XU, use other references: check the engine code before ordering.

Related products

With the head removed, renew the inlet valves, exhaust valves and guides as well: the whole assembly will benefit from firmer springs and fresh sealing:

Inlet valves PSA EW10J4S →
Exhaust valves PSA EW10J4S →

16 other products in the same category

Viewed products

Loading...