Skip to content
  • On order
Reinforced exhaust valves Honda Civic Integra Accord K20A K24 Reinforced exhaust valves Honda Civic Integra Accord K20A K24

Reinforced exhaust valves Honda Civic Integra Accord K20A K24

€129.87 (tax incl.)
€162.34 (tax incl.) -20%

Set of 8 reinforced exhaust valves for the Honda K20A and K24.

  • Brands: SUPERTECH, FERREA
  • Engines: K20A2, K20A3, K20A8, K24A2
  • Dimensions: 30 mm head (standard), 30.5, 31 or 31.5 mm, 5.5 mm stem
  • Material: black nitride or EV8 stainless steel, Inconel, titanium or special alloy
F5508*8
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

Honda engines covered

Honda's K series brings together the 1,998 cc K20A (86 mm bore and stroke) and the 2,354 cc K24 (87 mm bore, 99 mm stroke), two four-cylinder engines with twin camshafts and 16 valves. From 2001 the K20A powers the Civic VII and VIII, including the EP3 Type R, and the DC5 Integra; the K24A is fitted here to the Accord VI Aerodeck and VII.

Each cylinder head carries 8 exhaust valves. On the K20A2 of the EP3 Civic Type R, the original 14721-PRB-A00 valve has a 30.2 mm head, a 5.5 mm stem and a 108.7 mm overall length; two 14781-PRB-A01 collets hold it. The longer the engine stays high in the rev range, the hotter this valve runs.

SUPERTECH and FERREA reinforced exhaust valves

Because it opens onto the combustion gases, this valve operates in the hottest zone of the engine. Measured in the metal, its head reaches 760 to 870 °C on an unboosted K20A or K24, and goes past 1,000 °C once the engine is turbocharged or supercharged. Roughly three quarters of that heat escape through the seat, close to 20 % through the guide. Steel weakens as it warms up: the EV8 family, our reference here, accepts 550 MPa at 600 °C, then just 300 MPa at 800 °C. Loading it harder, spinning it faster or adding boost lifts the temperature further; the head fatigues, distorts and sealing suffers.

Coping with such heat calls for different materials. SUPERTECH offers three: black nitride stainless steel (HEVN), whose hardened, smooth surface limits friction and wear; Inconel (HEVI), a nickel superalloy retaining 860 MPa at 730 °C and 554 MPa near 815 °C, nearly 85 % above EV8 at about 800 °C, recommended with boost; titanium (HEVT), 1.9 mm shorter than original. FERREA adds its Competition Plus range in special alloy, quoted with 20 % greater hot strength and seats lasting 25 % longer, the 6000 series combining EV8 stainless steel and a hard chrome stem, and the 5000 series in special alloy.

Three oversizes are listed, +0.5, +1 and +1.5 mm: only the head grows, up to 31.5 mm. The chamber purges sooner, fresh air finds its place and output climbs. Each exhaust seat is then recut to suit the new head.

Exhaust valve technical specifications

Part numberBrandSizeHead Ø
OEM 30.2 mm
Stem Ø
OEM 5.5 mm
Length
OEM 108.7 mm
GroovesMaterial
HEVN-1020F-8 SUPERTECH Standard 30 mm 5.5 mm 108.7 mm 1 Black nitrided stainless steel
HEVI-1020D-8 SUPERTECH Standard 30 mm 5.5 mm 108.7 mm 1 Inconel
HEVT-1020F-8 SUPERTECH Standard 30 mm 5.5 mm 106.8 mm 1 Titanium
HEVN-1021F-8 SUPERTECH +0.5 mm 30.5 mm 5.5 mm 108.8 mm 1 Black nitrided stainless steel
HEVI-1021D-8 SUPERTECH +0.5 mm 30.5 mm 5.5 mm 108.8 mm 1 Inconel
HEVN-1030F-8 SUPERTECH +1 mm 31 mm 5.5 mm 108.8 mm 1 Black nitrided stainless steel
HEVI-1030D-8 SUPERTECH +1 mm 31 mm 5.5 mm 108.8 mm 1 Inconel
HEVT-1022F-8 SUPERTECH +1 mm 31 mm 5.5 mm 106.8 mm 1 Titanium
HEVN-1033F-8 SUPERTECH +1.5 mm 31.5 mm 5.5 mm 108.8 mm 1 Black nitrided stainless steel
HEVI-1033D-8 SUPERTECH +1.5 mm 31.5 mm 5.5 mm 108.8 mm 1 Inconel
F1546P*8 FERREA Standard 30 mm 5.5 mm 109.2 mm Special alloy
F1547P*8 FERREA +1 mm 31 mm 5.5 mm 109.2 mm Special alloy
F5508*8 FERREA Standard 30 mm 5.5 mm 109.2 mm Special alloy
F5509*8 FERREA +1 mm 31 mm 5.5 mm 109.2 mm Special alloy
F6071*8 FERREA Standard 30 mm 5.5 mm 109.2 mm EV8 stainless steel, hard chrome stem
F6072*8 FERREA +1 mm 31 mm 5.5 mm 109.2 mm EV8 stainless steel, hard chrome stem

Valve fitting

PartHonda originalReinforced
Collets 14781-PRB-A01 K10034
Valve stem seals 12210-PZ1-003 / 12211-PZ1-003 VS-H5.5E-8 / VS1002*8 (exhaust)
Valve guide 12205-PNA-305 (oversize) GDE-HK55-E-8

The SUPERTECH valves on this page have a single groove: they are fitted with single groove collets.

At 30 mm the seats stay as they are; at 30.5, 31 or 31.5 mm, the 8 exhaust seats are cut to the diameter of the new head.

As the titanium valves are 1.9 mm shorter than standard, their fitting is prepared with the cylinder head off. For valve stem seals, Honda fits the PZ1 part numbers on the K20A2 (12210-PZ1-003 / 12211-PZ1-003, then -004) or 12211-P45-G01.

Technical guide

Our brands

SUPERTECH SUPERTECH, rooted in Silicon Valley, has spent more than 30 years producing competition valves and springs, plus guides and retainers machined from titanium. Stainless, titanium or Inconel, every one of its valves is engineered around a given engine, then put to the test by respected circuit and rally tuners.
FERREA FERREA Racing Components, set up in 1978 by Horacio Ferrea with Daniel Urrutia, turns out valves in stainless steel, titanium and nickel-rich alloys in Florida as well as in Argentina. Tuners across the globe rely on the brand, from NASCAR to drag racing.

How to choose

The collets, seated under the retainer, hook the valve by its groove; each SUPERTECH valve has a single one and takes single groove collets. What is left to pick is size and material, which set how much you gain.

CriterionOption 1Option 2
Size Standard, 30 mm
For exhaust seats never recut. SUPERTECH in black nitride stainless, Inconel or titanium; FERREA Competition Plus, 6000 series or 5000 series, those last three for the K20 only.
+0.5 to +1.5 mm, 30.5 to 31.5 mm
A wider head speeds up cylinder emptying and improves filling, hence a power gain (around 10 to 12 cfm per mm of head). Seat cutting to that new size can also rescue reground ones. Up to +1.5 mm from SUPERTECH, +1 mm from FERREA.
Material Stainless steel or special alloy
For an unboosted K20A or K24, on road as on track, with no other part to change. SUPERTECH in black nitride stainless; FERREA in EV8 stainless with hard chrome stem (6000 series) or in special alloy (Competition Plus, 5000 series), K20 only: on a K24, pick a SUPERTECH.
Inconel or titanium
Inconel, a nickel superalloy, keeps its strength past 800 °C: the version to fit with a turbo, a supercharger or extended full-load running. SUPERTECH titanium, 1.9 mm shorter than original, is fitted with the head off. Single groove collets, ideally new.

When reinforced valves become necessary

  • Sharper camshafts or stiffened valve springs
  • Engine taken to the limiter more often and for longer
  • Boost added (Inconel version recommended)
  • Repeated track days or race preparation
  • Head rebuild with pitted, warped or already reground exhaust valves

Vehicle compatibility

ModelEngine codePowerYears
Civic VII 2.0 Type-R (EP3) K20A2 200 hp 2001-2005
Civic VII 2.0 i Sport (EV1) K20A2 / K20A3 / K20A8 160 hp 2001-2005
Civic VII 2.0 (ET1) K20A2 / K20A3 / K20A8 155-160 hp 2003-2006
Civic VIII 2.0 (FD2) K20A2 / K20A3 / K20A8 155 hp 2006-2012
Integra 2.0 (DC5) K20A2 / K20A3 / K20A8 160-200 hp 2002-2008
Accord VI Aerodeck 2.4 VTEC (CF) K24A2 160 hp 2003-2005
Accord VII 2.4 VTEC (CM5) K24A2 160 hp 2002-2005
Accord VII 2.4 VTEC (CM2) K24A2 160 hp 2003-2005

OEM part number (exhaust valve): 14721-PRB-A00 (K20A2, EP3 Civic Type R)

Important: a set of 8 covers a complete engine. The F1546P, F1547P, F5508, F5509, F6071 and F6072 are intended for the K20 only: on a K24, choose a SUPERTECH valve. The Acura RSX and TSX are not covered on this Honda page. The Accord VIII and IX with K24Z engines, whose standard exhaust head measures 31 mm, are not covered here.

Don't forget the inlet valves

K20A or K24 cylinder head off: the right time to renew the inlet side, valves and valve stem seals alike. The inlet valves made for these engines:

K20A K24A2 inlet valves →
Honda K20A3 K24A3 valve spring kit →

16 other products in the same category

Viewed products

Loading...