Skip to content
  • On order
Reinforced inlet valves HONDA K20A2 K20A3 K24A2 Reinforced inlet valves HONDA K20A2 K20A3 K24A2

Reinforced inlet valves HONDA K20A2 K20A3 K20A8 K24A2

€121.80 (tax incl.)
€152.26 (tax incl.) -20%

Set of 8 reinforced inlet valves for HONDA K20A2, K20A3, K20A8 and K24A2 (Civic VII, Integra DC5, Accord VII).

  • Brands: SUPERTECH, FERREA
  • Engines: K20A2, K20A3, K20A8, K24A2
  • Dimensions: 35.0 to 37.0 mm head, 5.47 or 5.48 mm stem
  • Material: black nitrided or chromed-stem stainless steel (including EV8)
F5510*8
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

HONDA engines covered

The K20A2, K20A3 and K20A8 are Honda's 1,998 cc double overhead camshaft 16-valve VTEC four-cylinders; the K24A2 is the 2,354 cc version. They power the Civic VII (2.0 i Sport, Type-R EP3), the Integra DC5 and the Accord VII Tourer 2.4, from 155 to 200 hp, from 2001 to 2008.

Each engine has 8 inlet valves, two per cylinder, 109.1 mm long as standard and held by Honda 14781-PRB-A01 (K20A2) or 14781-PR7-A01 (K20A3, K20A8) collets. A sharper camshaft, stiffer springs, a higher rev limit or forced induction ask far more of them than stock use.

SUPERTECH and FERREA reinforced inlet valves

In a K20A, the inlet valve admits fresh air and then blocks it off, at a frantic rate once VTEC switches over and the engine takes off. Its head comes back down on the seat every time; the stem, for its part, never stops gliding in its guide. It works from 400 to 550 °C, a range where factory chrome-silicon steel loses its footing: 500 MPa at 500 °C, but 250 MPa at 600 °C, barely hotter, which is 50 % of strength gone. Extra lift, hardened springs, more revs or a supercharger all increase shocks, friction and heating.

SUPERTECH uses a chrome-nickel stainless cut out for racing, from the EV8 line (21-4N): 650 MPa at 500 °C, 30 % more than factory steel, 550 MPa at 600 °C, 120 % more; black nitriding hardens and polishes the stem. FERREA covers the K20A with three series: the Competition Plus, a stainless part whose stem is chromed, improved by 20 % in thermal strength and endurance, with a seat lasting 25 % longer; the 6000 in EV8 stainless, hard chrome stem; the 5000 in stainless, hard chrome stem.

Beyond the 35.0 mm standard size, SUPERTECH lists four oversizes, from 35.5 to 37.0 mm (+0.5 to +2 mm), with a 5.48 mm stem and 108.85 mm length; FERREA adds a +1 mm, 36.0 mm size in each series. The enlarged head lets more air in and the engine ends up stronger, once each inlet seat is reworked to the new diameter. Flat or dished heads up to 36.0 mm, flat beyond that.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
HIVN-1020D-8 SUPERTECH Standard 35.0 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1020F-8 SUPERTECH Standard 35.0 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1021D-8 SUPERTECH +0.5 mm 35.5 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1021F-8 SUPERTECH +0.5 mm 35.5 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1022D-8 SUPERTECH +1 mm 36.0 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1022F-8 SUPERTECH +1 mm 36.0 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1022.5F-8 SUPERTECH +1.5 mm 36.5 mm 5.48 mm 108.85 mm Black nitride stainless steel
HIVN-1023F-8 SUPERTECH +2 mm 37.0 mm 5.48 mm 108.85 mm Black nitride stainless steel
F1548P*8 FERREA Standard 35.0 mm 5.47 mm 109.3 mm Stainless steel, chromed stem
F1549P*8 FERREA +1 mm 36.0 mm 5.47 mm 109.3 mm Stainless steel, chromed stem
F6073*8 FERREA Standard 35.0 mm 5.47 mm 109.3 mm EV8 stainless steel, hard chrome stem
F6074*8 FERREA +1 mm 36.0 mm 5.47 mm 109.3 mm EV8 stainless steel, hard chrome stem
F5510*8 FERREA Standard 35.0 mm 5.47 mm 109.3 mm Stainless steel, hard chrome stem
F5511*8 FERREA +1 mm 36.0 mm 5.47 mm 109.3 mm Stainless steel, hard chrome stem

FERREA: flat head for F5510*8 and F5511*8.

Dished heads: HIVN-1020D-8, HIVN-1021D-8, HIVN-1022D-8. Flat heads: HIVN-1020F-8, HIVN-1021F-8, HIVN-1022F-8, HIVN-1022.5F-8, HIVN-1023F-8; HIVN-1023F-8 with back cut.

Fitting details

PartHONDA originalReinforced
Collets 14781-PRB-A01 (K20A2) / 14781-PR7-A01 (K20A3, K20A8) KPR-5.5-7A-ST
Valve stem seals 12210-PZ1-003 / 12211-PZ1-003 VS-H5.5I-8 / VS1003*8
Valve guide 12204-PNA-305 (repair size) GDE-HK55-I-8

The +0.5 to +2 mm oversizes require the inlet seats to be cut to the diameter of the chosen head, from 35.5 to 37.0 mm, workshop work to plan with the cylinder head rebuild.

Valve clearance is set by adjusting screws on these engines: after replacing the valves, check and set it (0.21 to 0.25 mm cold on the inlet side on the K20A2 and K20A3).

Technical guide

Our brands

SUPERTECH SUPERTECH, from its San Jose site in California, has been developing racing valves, with their springs, retainers and guides, for more than 30 years. Each valve answers a given head, undergoes ultrasonic, radiographic and laser checks, and is then refined alongside engine builders.
FERREA FERREA Racing Components was born in Florida in 1978 on the initiative of Horacio Ferrea and Daniel Urrutia, two Argentine engine builders. In Fort Lauderdale, every valve is hammered out of a single bar and finished on CNC machines; it powers NASCAR, drag and circuit engines.

How to choose

All these valves keep the factory stem: you first choose the size, based on seat condition and the air you want, then the brand and head shape.

CriterionOption 1Option 2
Size Standard size
35.0 mm head, the Honda dimension, available from SUPERTECH (HIVN-1020D-8, HIVN-1020F-8) and FERREA (F1548P*8, F6073*8, F5510*8). The one to choose if the head has never-recut seats, for a K20A used every day or an original restoration.
+0.5 to +2 mm oversizes
35.5 to 37.0 mm heads: the enlarged opening at the seat swallows extra air and brings power, about 10 to 12 cfm per millimetre gained. The seats then need to be cut to the chosen size, preferably reworking the ports too; these sizes bring seats recut once or more back to life.
Brand SUPERTECH
Black nitrided stainless in five sizes, dished (D) or flat (F) head; the HIVN-1023F-8 gets a back cut. Hardened, smooth stem, at ease in a tuned VTEC, for road use and track alike.
FERREA
Three series: Competition Plus, 6000 and 5000, each at standard size or +1 mm, 109.3 mm long; flat head on the 5000. The choice for the most heavily loaded race heads.

When reinforced valves become necessary

  • Higher-lift camshafts or much stiffer springs
  • Rev limiter moved back
  • Turbo or supercharger grafted onto the K20A
  • Head meant for track, hillclimbs or rallies
  • Factory valves scored, tired or already recut once

Compatible vehicles

ModelEngine codePowerYears
Civic VII 2.0 i Sport (EV1) K20A3 160 hp 2001-2005
Civic VII 2.0 (EV1) K20A3 162 hp 2001-2005
Civic VII 2.0 Type-R (EP3) K20A2 200 hp 2001-2005
Civic VII Berline 2.0 (ET1) K20A3 160 hp 2003-2005
Civic VII Berline 2.0 iVtec (ET1) K20A3 155 hp 2004-2006
Integra Coupé 2.0 (DC5) K20A3 160 hp 2002-2008
Integra Coupé 2.0 Type-R (DC5) K20A2 200 hp 2004-2008
Accord VII Tourer 2.4 Vtec E (CM2) K24A2 160 hp 2003-2005

OEM part number (inlet valve): 14711-PRB-A01 (K20A2); 14711-PNL-E00, 14711-PNA-000 (K20A3); 14711-PNA-000 (K20A8)

Important: the K24Z3 and K24Z7, whose standard inlet head measures 36.0 mm, and the K20C of the Civic Type R are not covered here. The FERREA sets cover the K20A2, K20A3 and K20A8, not the K24A2.

Related products

When rebuilding a K20A or K24A2 head, also plan reinforced exhaust valves, a matching valve spring kit and new stem seals; both buttons below lead there:

HONDA Civic Integra Accord K20A K24 exhaust valves →
HONDA K20A K20Z K24 F20C F22C reinforced valve spring kit →

16 other products in the same category

Viewed products

Loading...