Skip to content
  • In stock
Tri-metal crankshaft main bearings ACL Honda K20C1 Tri-metal crankshaft main bearings ACL Honda K20C1 Tri-metal crankshaft main bearings ACL Honda K20C1 Tri-metal crankshaft main bearings ACL Honda K20C1 Tri-metal crankshaft main bearings ACL Honda K20C1 Tri-metal crankshaft main bearings ACL Honda K20C1

Tri-metal crankshaft main bearings ACL Honda K20C1

€112.78 (tax incl.)
€125.32 (tax incl.) -10%

Set of tri-metal crankshaft main bearing half shells for the five main bearings of the Honda K20C1 of the Civic Type R.

  • Brand and treatment: ACL Race, untreated
  • Fitments: Honda Civic Type R (FK2, FK8, FL5)
  • Engine code: K20C1
  • Available sizes: standard to +0.25 mm, increased clearance version (HX)
5M1985H-STD
6 in stock in Europe (72h lead time)
Pay in installments

The Honda K20C1 engine of the Civic Type R

The K20C1 is the 2.0 litre turbocharged four-cylinder of the Honda Civic Type R (FK2, FK8 and FL5). All the models listed below share the same crankshaft journal and housing dimensions: a single bearing set covers the whole family.

The crankshaft of this engine runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series tri-metal set shown here replaces them on built engines.

From the factory, Honda fits these engines with main bearings under part number 13321-RPY-G02, and its workshop manual specifies a running clearance of 0.017 to 0.041 mm.

Tri-metal main bearings

Three layers make up a trimetal bearing: the steel back for stiffness, the copper-lead intermediate layer for load capacity, then the anti-friction running layer that protects the main journal. The complete set covers the five main bearings of the crankshaft. The upper and lower half shells are different: each goes in its own position.

Where an aluminium bi-metal bearing, designed for low to medium loads, withstands about 8,000 psi, a performance trimetal bearing goes up to 12,000 psi: 50% extra margin. That is what keeps it durable on an engine boosted by a turbo or supercharger, or pushed to high rpm.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankshaft journal Ø 54.980 / 55.000 mm
Housing bore Ø 59.000 / 59.020 mm
Width 20 mm
ReferenceBrand and treatmentSizeWall thickness (mm)
5M1985H-STD ACL Race - Untreated Standard 2.002
5M1985HX-STD ACL Race - Untreated Std, increased clearance (HX) 1.989
5M1985H-.025 ACL Race - Untreated +0.025
5M1985H-.25 ACL Race - Untreated +0.25

Running clearance

Between the main journal and the bearing there is a small gap, the running clearance, in which the oil film circulates.

In operation there is no metal-to-metal contact: the main journal turns on this oil film, which supports the whole load. The clearance determines its thickness. A clearance that is too tight hinders oil flow, heats the assembly and promotes seizure; one that is too wide lets oil leak away, weakens the film and makes oil pressure drop. The correct clearance balances oil flow and film strength.

Size / gradeWhen to choose itACL Race Series
Standard (STD) Standard journal, not reground 0.057 to 0.068 mm
Increased clearance (HX) Wider clearance: high oil flow, high rpm 0.082 to 0.093 mm
+0.025 mm Polished journal 0.057 to 0.068 mm
+0.25 mm Journal reground to 0.25 mm 0.057 to 0.068 mm

Checking on assembly: lay a calibrated strip (Plastigauge) on the journal, torque the main cap to spec, then compare the crushed strip against the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

Designed for engine building and motorsport, these ACL trimetal main bearings carry much more load than an original bearing, whether the engine gains power, revs higher or receives a turbo or supercharger. They are available in several sizes: the standard size, a +0.025 mm size for a main journal that has only been polished, a +0.25 mm regrind size and the HX version with increased clearance for high-revving engines or engines needing a high oil flow. That makes it possible to put a reground crankshaft back into service without changing range and to set the clearance for the oil and use.

The brand

ACL Bearing Company ACL Bearing Company has been making high-performance engine bearings in Australia since 1949. Its Race Series offers precise trimetal bearings, available in many sizes and proven in tuned and racing engines worldwide.

Vehicle compatibility

This main bearing set fits the K20C1 four-cylinder of the following Honda Civic Type R models:

BrandModel (chassis)Engine codePowerYears
HONDA CIVIC IX (FK) 2.0 i-VTEC Type R (FK2) K20C1 310 hp 2015–2016
HONDA CIVIC X Hatchback (FC_, FK_) 2.0 Type-R K20C1 306–320 hp 2017–
HONDA CIVIC XI Hatchback (FL) Type-R K20C1 300–330 hp 2022–

Why replace the bearings

When a main bearing gives way, the damage quickly spreads beyond the part itself: a scored main journal, debris carried through the whole oil circuit, a crankshaft to regrind at the very least, sometimes a damaged block. A bearing set costs far less than a regrind and is nothing compared with a complete engine rebuild. It is the cheapest part of the crankshaft assembly, yet the one whose failure is most expensive.

11 other products in the same category

Viewed products

Loading...