Skip to content
  • On order
Reinforced ARP bolts for OEM rods HONDA F20C F22C Reinforced ARP bolts for OEM rods HONDA F20C F22C

Reinforced ARP bolts for OEM rods HONDA F20 F22

€161.97 (tax incl.)
€190.55 (tax incl.) -15%

Kit of ARP2000 rod bolts replacing the original bolts on the OEM rods of the Honda F20C and F22C four-cylinders (S2000 AP1 and AP2).

  • Brand: ARP
  • Engine: F20C / F22C
  • Grade: ARP2000
ARP-208-6002

This pack contains

0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

The engines concerned

The VTEC four-cylinder of the Honda S2000 comes in two capacities: the 2.0-litre F20C (87 mm bore, 84 mm stroke), fitted from 1999 to 2009 to the S2000 AP1, and the 2.2-litre F22C (87 mm bore, 90.7 mm stroke), fitted from 2003 to 2009 to the AP2.

The original connecting rod bolt of both engines carries the reference 13204-PCX-003: Honda prescribes tightening it to 25 Nm then 90° of angle, and it is a single-use bolt.

Reinforced ARP bolts for connecting rods

At every revolution, the rod bolt takes the pull of the rod and piston assembly, which tries to force the cap away through inertia. As original equipment, it is sized for stock power and is replaced at every strip-down.

This kit replaces the original bolt of each rod with an ARP2000 bolt that the ARP instruction sheet has you tighten by stretch, measured with a gauge, the 61 Nm torque being used only when no gauge is available. ARP2000 is an alloy steel developed by ARP and heat treated to 220,000 psi tensile strength; its threads are rolled after heat treatment. Standard engine fasteners commonly fall into classes 10.9 and 12.9, i.e. 150,800 to 176,900 psi minimum strength: ARP2000 sits 24 to 46% above that.

Technical specifications

Part numberBrandGrade / materialHeadThreadUnder-head length
ARP-208-6002 ARP ARP2000 Not published Not published

As the ARP instruction sheet requires, the entry of the bolt hole in the rod cap is given a chamfer wide enough to leave the fillet radius under the head free; no washer goes under the bolt.

Tightening torque and stretch

ReferenceTightening torqueStretch
ARP-208-6002 61 Nm 0.140 - 0.152 mm

ARP recommends tightening to a measured stretch, which gives a more accurate preload than torque alone, given as a fallback. Torque and stretch figures assume ARP lubricant.

Figures taken from the ARP 208-6002 instruction sheet, revision in force on the day of publication. Should any difference appear, the official instruction sheet takes precedence. Read the ARP 208-6002 instruction sheet

Assembly is done without thread locker, as the ARP instruction sheet calls for none: ARP Ultra-Torque grease is applied to the threads and under the head of each bolt.

The ARP instructions for this kit require the big ends to be checked and resized once the fasteners are fitted: this job belongs to an equipped machine shop.

Measuring bolt stretch

Measuring the stretch of a rod bolt

With the stretch gauge, you read directly how much the bolt stretches during tightening: the dial gauge sits on both ends of the fitted bolt, and tightening stops when the stretch reaches the value in the table. Friction no longer comes into play, hence a more consistent preload on a heavily stressed engine.

Technical guide

Tightening is done with ARP assembly grease, on the threads and under the head: the torque and stretch figures in the table were established with it.

The ARP brand ARP

ARP (Automotive Racing Products) came into being in the early 1970s, when Gary Holzapfel, who came from the aerospace industry, decided to tackle the engine failures caused in motorsport by inadequate fasteners. Today the brand produces thousands of part numbers in California for the cylinder head, the main bearings and the connecting rods, in materials suited to each application, with manufacturing known for its consistency.

Vehicle compatibility

BrandModel (chassis)Engine codePowerYears
Honda S2000 (AP1) F20C / F20C1 / F20C3 231-250 hp 1999-2009
Honda S2000 (AP2) F22C1 239-243 hp 2003-2009

OEM reference (rod bolt): 13204-PCX-003

Important: This kit only fits the original F20C and F22C rods, which use the 13204-PCX-003 bolt: check this before ordering, as a rod drilled for a bolt of another diameter cannot take it.

Why is it the most cost-effective solution?

The original rod bolt, taken to its yield point by torque then angle tightening, keeps a permanent stretch. The ARP2000 bolts, reinforced and stronger, withstand higher engine speeds and inertia loads, which reduces the risk of a fastener-related failure and saves a far heavier engine repair.

Matching connecting rod bearings

To complete the bottom-end rebuild, we offer the connecting rod bearings intended for this engine.

Connecting rod bearings Honda F20C F22C →

  • Brand
    ARP
  • Reference
    ARP-208-6002
  • EAN13
    0672036032609

16 other products in the same category

Viewed products

Loading...