Skip to content
  • In stock
Tri-metal crankshaft main bearings Honda S2000 F20C F22C Tri-metal crankshaft main bearings Honda S2000 F20C F22C

Tri-metal crankshaft main bearings Honda S2000 F20C F22C

€82.84 (tax incl.)
€92.04 (tax incl.) -10%

Set of 10 tri-metal crankshaft main bearing half shells for Honda S2000 F20C and F22C engines (Ø 54.98 mm).

  • Brands: ACL Race and King Racing
  • Fitments: Honda S2000 (AP)
  • Engine codes: F20C1, F22C1
  • Available sizes: standard to +0.25 mm, increased clearance versions (HX / STDX)
5M1913H-STD
33 in stock in Europe (72h lead time)
Pay in installments

The Honda F20C and F22C engines of the S2000

The F20C (2.0 litre) and F22C (2.2 litre) are the four-cylinder 16-valve VTEC engines of the Honda S2000. All the engines listed below share the same crankshaft journal and housing dimensions: a single bearing set covers the whole family.

The crankshaft of these engines runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series and KING RACING tri-metal sets shown here replace them on built engines.

For these main bearings, the Honda workshop manual specifies a running clearance of 0.017 to 0.041 mm.

Tri-metal main bearings

In a trimetal bearing, a steel back carries a copper-lead intermediate layer with high load capacity, itself covered by an anti-friction running layer that spares the main journal. The set is supplied complete: 10 half shells, i.e. 5 pairs.

Trimetal targets high, sustained loads, whereas aluminium bi-metal is limited to low to medium loads: about 8,000 psi for the latter, up to 12,000 psi for a performance trimetal, 50% more. The benefit shows in strength and durability on turbo, supercharged and high-revving engines.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankshaft journal Ø 54.976 / 55.000 mm
Housing bore Ø 60.000 / 60.020 mm
Width 20 mm
King bearings
Crankshaft journal Ø 54.98 / 55.00 mm
Housing bore Ø 60.00 / 60.02 mm
Width 20 mm
ReferenceBrand and treatmentSizeWall thickness (mm)
5M1913H-STD ACL Race - Untreated Standard 2.504
5M1913HX-STD ACL Race - Untreated Std, increased clearance (HX) 2.491
5M1913H-.025 ACL Race - Untreated +0.025 2.5165
5M1913H-.25 ACL Race - Untreated +0.25 2.629
MB5673XP King Racing - Untreated Standard 2.504
MB5673XP STDX King Racing - Untreated Std, increased clearance (STDX) 2.491
MB5673XP.026 King Racing - Untreated +0.026 2.517
MB5673XP0.25 King Racing - Untreated +0.25 2.631

Running clearance

Running clearance is the gap between the bearing and the main journal, filled by the oil film.

While the engine turns, the main journal floats on this oil film, which carries the load without direct contact with the bearing. Film thickness depends on clearance: too tight, oil passes poorly, temperature rises and the risk of seizure grows; too wide, oil escapes, the film carries less and oil pressure decreases. A correct clearance ensures both sufficient lubrication and a well-maintained film.

Size / gradeWhen to choose itACL Race SeriesKing XP
Standard (STD) Standard journal, not reground 0.057 to 0.068 mm 0.055 mm - 0.068 mm
Increased clearance (HX / STDX) Wider clearance: high oil flow, high rpm 0.082 to 0.093 mm 0.080 mm - 0.093 mm
+0.025 / +0.026 mm Polished journal 0.057 to 0.068 mm 0.055 mm - 0.068 mm
+0.25 mm Journal reground to 0.25 mm 0.057 to 0.068 mm 0.055 mm - 0.068 mm

Check at assembly: lay a calibrated strip (Plastigauge) on the journal, tighten the main cap following the manufacturer's procedure, then compare the width of the crushed strip with the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

These ACL and King trimetal main bearings are aimed at built engines and racing: where a standard bearing quickly reaches its limit, they accept more power, more rpm and more boost. The range includes the standard size, a +0.025 / +0.026 mm size for a main journal that has only been polished, a +0.25 mm regrind size and the HX / STDX version with increased clearance for high-revving engines or engines needing a high oil flow. It allows the same part number to be kept after the crankshaft is reground and the clearance to be tailored to the oil used and the engine's duty.

The two brands

ACL An Australian specialist in high-performance engine bearings since 1949, ACL Bearing Company produces the Race Series: precisely made trimetal bearings, available in numerous sizes and recognised on built engines across the world.
King Racing Since the 1960s, Israel's King Engine Bearings has built high-performance engine bearings; its pMax Black trimetal alloy bearings are sized for heavy loads.

Construction and advantages

Criterion ACL Race Series King Racing
Cross-section Cross-section of an ACL Race Series trimetal bearing Cross-section of a King Racing trimetal bearing
Type High-performance trimetal bearing High-performance trimetal bearing
Country of manufacture Australia Israel
Construction Trimetal: steel back, copper layer, soft surface Trimetal: steel back, copper layer, soft surface
Alloy Race Series (copper-lead) pMax Black (hardened copper-lead)
Protective coating No No
Available sizes Standard to +0.25 mm (+ increased clearance HX) Standard to +0.25 mm (+ increased clearance STDX)

Vehicle compatibility

This main bearing set fits the Honda F20C and F22C engines sharing the same crankshaft journal and housing dimensions:

BrandModel (chassis)Engine codePowerYears
Honda S2000 (AP) 2.0 Vtec / 2.0 / 2.2 Vtec (AP2) / 2.2 F20C1, F22C1 231–243 hp 1999–2008

Why replace the bearings

Replacing the bearings during a build or rebuild guards against the most expensive failure: a worn-out main bearing scores the main journal, contaminates the oil circuit with debris and forces at least a crankshaft regrind, or even block repairs. Against such costs a new set weighs little: it is the cheapest part of the crankshaft assembly, but the one whose failure costs the most.

16 other products in the same category

Loading...