Skip to content
  • On order
Reinforced valve spring kits Honda S2000 F20C F22C1 Reinforced valve spring kits Honda S2000 F20C F22C1

Reinforced valve spring kit Honda S2000 F20C F22C1

€346.18 (tax incl.)
€461.57 (tax incl.) -25%

Kit of 16 reinforced valve springs for the F20C and F22C1 engines of the Honda S2000.

  • Brand: FERREA
  • Engines: 2.0 16V F20C and 2.2 16V F22C1, Honda S2000 (AP1 and AP2)
  • Springs: single conical or double
  • Contents: 16 springs, with retainers and collets depending on the kit
S2022*16
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

Honda engines covered

This kit fits the engines of the Honda S2000: the 2.0-litre F20C (AP1, 2000 to 2003) and the 2.2-litre F22C1 (AP2, 2004 to 2008). Both are naturally aspirated four-cylinders with 16 valves and VTEC valve timing.

In standard form (F20C), each valve is closed by a single spring: 14761-PCX-003 on the inlet side and 14762-PCX-003 on the exhaust side. A retainer 14765-PCX-000, a spring seat 14775-PCX-000 and collets 14781-PR7-A01 go with it.

FERREA reinforced valve spring kit

Each spring presses its valve down onto the seat and keeps it tracking the cam profile. At high revs the valve's own inertia starts to win: it lifts off the lobe, drops back with a bounce and can even brush the piston. Tuners call it valve float.

Seat load: 467 N for the S2022 (single, 45.7 mm), 400 N for the KT4011 (double, 42.0 mm).

Valve spring kit technical specification

Part numberBrandSpringsOuter / inner ØSeat pressureOpen pressureRateMax liftKit contents
S2022*16 FERREA Single, conical Base 28.1 / 18.9 mm, top 23.9 / 14.7 mm 467 N at 45.7 mm 54.8 N/mm 15.2 mm 16 springs
KT4011 FERREA Double Outer 30.5 / 22.9 mm
Inner 22.9 / 17.5 mm
400 N at 42.0 mm 51.1 N/mm 13.0 mm 16 springs, 16 upper retainers, 16 lower spring seats, 16 collets

Valve spring kit fitting details

PartHonda original (F20C)Reinforced spring kit
Spring Inlet 14761-PCX-003; exhaust 14762-PCX-003 Kit specific: S2022 (single, conical) or S10074 (double, KT4011)
Retainer 14765-PCX-000 E12030 (titanium), ordered separately; E11045 (titanium), supplied with the KT4011
Spring seat 14775-PCX-000 SL1119 (inlet), SL1120 or SL1121 (exhaust), ordered separately; SL1035, supplied with the KT4011
Collets 14781-PR7-A01 K10034, supplied with the KT4011

The FERREA S2022 spring is fitted with the titanium retainer E12030 and a spring seat: SL1119 on the inlet side, SL1120 (standard camshaft) or SL1121 (stage 2 camshaft) on the exhaust side. The original spring seat is discarded. These parts are not included in the kit of 16 springs. The KT4011 kit, by contrast, brings everything: 16 double springs S10074, 16 titanium retainers E11045, 16 spring seats SL1035 and 16 collets K10034; here too the original spring seat is discarded.

Fitted height is measured on a closed valve, between the bearing face of the spring seat and the lower face of the retainer. FERREA quotes its seat pressure for one height only. If the spring ends up higher, say after skimming the valve seats, the pressure falls by the spring rate for every extra millimetre (height and seat pressure in the table below).

S2022*16 KT4011
Installed height 45.7 mm 42.0 mm
Seat pressure at this height 467 N 400 N

Technical guide

Our brands

FERREA FERREA Racing Components dates from 1978, when two Argentine builders, Daniel Urrutia and Horacio Ferrea, set up shop in Florida. Its own workshops turn out valves, springs, tappets plus rockers, and the range is raced on drag strips, in NASCAR and around circuits.

How to choose

A firmer spring lets an engine pull more revs, run a wilder camshaft or take more boost before the valve floats. The S2022 presses on the seat with 467 N, the KT4011 with 400 N. Before buying, make sure your cam lift stays under 15.2 mm (S2022) or 13.0 mm (KT4011), the ceilings set for these kits; measuring it takes minutes. Too soft and the valve bounces off its seat, too hard and the lobes wear early.

CriterionKey point
Choosing the pressure The load follows three things: how high the camshaft lifts, the engine speed you want and, if there is one, the turbo or supercharger pressure. As these climb the load has to climb too, without crossing the kit's lift limit. Here it is 467 N or 400 N at the seat, depending on the kit. Going firmer than required gains nothing and tires lobes and rocker arms. FERREA places this spring in its Street Performance series.
Single or double spring The S2022 gives each valve one conical spring, with no inner spring; the KT4011 fits two nested springs, which spread the load and damp vibration more effectively. Both layouts are therefore on offer.

When reinforced springs become necessary

  • Camshaft with noticeably more lift
  • Higher rev ceiling
  • Turbo or supercharger added
  • Head rebuilt for circuit racing, drifting or rallying
  • Tired stock springs, or valve float heard near the rev limit

Compatible vehicles

ModelEngine codePowerYears
Honda S2000 (AP1) 2.0 VTEC F20C 2000-2003
Honda S2000 (AP2) 2.2 VTEC F22C1 2004-2008

OEM part number (valve spring): 14761-PCX-003 (inlet), 14762-PCX-003 (exhaust), for the F20C

Important: this kit is for the F20C and F22C1 engines of the Honda S2000. Check your engine code before ordering.

Related products

With the head on the bench for new springs, renewing the valves as well is sensible. Inlet and exhaust references for these engines follow:

Honda S2000 F20C F22C1 inlet valves →
Honda S2000 F20C F22C exhaust valves →

16 other products in the same category

Viewed products

Loading...