Skip to content
  • In stock
Reinforced ARP bolts for OEM rods HONDA ACURA K20A K20A1 K20A2 K20A3 K20A4 K20A5 K20A6 K20A7 K20A8 K20A9 K20Z1 K20Z2 Reinforced ARP bolts for OEM rods HONDA ACURA K20A K20A1 K20A2 K20A3 K20A4 K20A5 K20A6 K20A7 K20A8 K20A9 K20Z1 K20Z2

Reinforced ARP bolts for OEM rods HONDA ACURA K20

€161.97 (tax incl.)
€190.55 (tax incl.) -15%

ARP2000 rod bolts replacing the original bolts on OEM rods of Honda and Acura K20A and K20Z engines.

  • Brand: ARP
  • Engine: K20A, K20A1, K20A2, K20A3, K20A4, K20A5, K20A6, K20A7, K20A8, K20A9, K20Z1, K20Z2, K20Z3, K20Z4
  • Dimensions: 3/8 in x 38 mm
  • Grade: ARP2000
ARP-208-6003
15 in stock in Europe (72h lead time)
Pay in installments

The Honda and Acura K20A and K20Z engines concerned

This kit is intended for the Honda and Acura K20A and K20Z engines, four-cylinder units of 2.0 litres with twin overhead camshafts, 16 valves and i-VTEC valve timing: Civic VII and VIII (including the Type R EP3 and FN2), Integra DC5 (including the Type R and Type S), Accord VII, CR-V II, FR-V, Stream and Stepwgn, as well as on the Acura RSX and CSX.

The K20A's original rod bolt is replaced by an ARP2000 cap screw that threads straight into the connecting rod to hold the cap, with no washer.

Reinforced ARP bolts for connecting rods

At every revolution, the rod bolt takes the pull of the rod and piston assembly, which tries to force the cap away through inertia. As original equipment, it is sized for stock power and is replaced at every strip-down.

Kit of ARP2000 cap screws, supplied without washers: the ARP instructions call for tightening to a measured stretch; without a gauge, a torque of 67.8 Nm remains possible. ARP2000 is an alloy steel developed by ARP and heat treated to 220,000 psi tensile strength; its threads are rolled after heat treatment. Standard engine fasteners commonly fall into classes 10.9 and 12.9, i.e. 150,800 to 176,900 psi minimum strength: ARP2000 sits 24 to 46% above that. The ARP2000 bolts hold up to 9,500 rpm (calculated estimate).

Technical specifications

Part numberBrandGrade / materialHeadThreadUnder-head length
ARP-208-6003 ARP ARP2000 Not published 3/8 in 38 mm

Tightening torque and stretch

ReferenceTightening torqueStretch
ARP-208-6003 67.8 Nm 0.203 - 0.216 mm

ARP gives priority to stretch control for an accurate preload; the torque in the table is used only when no gauge is available. Torque and stretch figures in the table apply with ARP lubricant.

Figures taken from the ARP 208-6003 instruction sheet, revision in force on the day of publication. Should any difference appear, the official instruction sheet takes precedence. Read the ARP 208-6003 instruction sheet

Assembly is done without thread locker, as the ARP instruction sheet calls for none: ARP Ultra-Torque grease is applied to the threads and under the head of each bolt.

According to the ARP instructions, the big ends must be checked and resized with the fasteners in place; plan a visit to a machine shop.

Measuring bolt stretch

Measuring the stretch of a rod bolt

Stretch measurement supplements torque tightening and gives the most accurate preload. It is done with the bolt in place: the gauge, fitted with a dial indicator, bears on both ends of the bolt and shows the stretch achieved, to be brought to the value in the table above. This avoids the variations caused by friction, which matters on a highly stressed engine.

Technical guide

Tightening is done with ARP assembly grease, on the threads and under the head: the torque and stretch figures in the table were established with it.

The ARP brand ARP

ARP (Automotive Racing Products) came into being in the early 1970s, when Gary Holzapfel, who came from the aerospace industry, decided to tackle the engine failures caused in motorsport by inadequate fasteners. Today the brand produces thousands of part numbers in California for the cylinder head, the main bearings and the connecting rods, in materials suited to each application, with manufacturing known for its consistency.

Vehicle compatibility

BrandModel (chassis)Engine codePowerYears
Honda Civic VII Type R (EP3) K20A, K20A2 200 / 215 hp 2000-2005
Honda Civic VII 2.0 i Sport (EV1) K20A3 160 / 162 hp 2001-2005
Honda Civic VII 2.0 (ES, ET) K20A3 155 / 160 hp 2003-2006
Honda Civic VIII 2.0 (FD2) K20A3, K20Z2 155 hp 2006-2012
Honda Civic VIII 2.0 (FD2) K20Z3 192 / 200 hp 2007-2011
Honda Civic VIII Type R (FD2) K20A5 224 hp 2007-2010
Honda Civic VIII Type R (FN2) K20Z4 201 / 241 hp 2006-2012
Honda Civic VIII Coupé 2.0 K20Z4 200 hp 2005-2011
Honda Accord VII 2.0 (CL7, CL8, CM1) K20A6, K20Z2 155 hp 2003-2008
Honda Accord VII 2.0 R (CL7) K20A 218 / 220 hp 2003-2008
Honda Accord VII 2.0 VTEC (CM4) K20A7 150 hp 2003-2006
Honda CR-V II 2.0 (RD4, RD5) K20A, K20A4, K20A5 150 / 152 / 156 / 158 hp 2001-2007
Honda FR-V 2.0 (BE3, BE4) K20A9 150 / 155 / 156 hp 2004-2011
Honda Integra Coupé 2.0 (DC5) K20A2, K20A3 160 / 200 hp 2002-2008
Honda Integra Type-R (DC5) K20Z1 220 hp 2002-2007
Honda Integra Type-S (DC5) K20Z1 209 hp 2004-2007
Honda Stream 2.0 (RN3, RN4) K20A, K20A1, K20A5 156 / 158 hp 2001-2006
Honda Stepwgn 2.0 (RF3, RF4, RG1, RG2) K20A6, K20A9 155 / 160 hp 2000-2009
Acura RSX 2.0 (DC5) K20A, K20A2, K20A3 158 / 162 / 203 / 220 hp 2001-2006
Acura RSX 2.0 Sport (DC5) K20A3 160 hp 2001-2006
Acura RSX Type S (DC5) K20A8 214 hp 2004-2005
Acura CSX 2.0 (sedan) K20Z2 156 hp 2005-2010
Acura CSX 2.0 (sedan) K20Z3 200 hp 2006-2010

Why is it the most cost-effective solution?

A K20A from a Civic Type R revved higher or fitted with forced induction asks its rod bolts to hold inertia loads that the original hardware was not sized for, and a broken bolt destroys the rod, the piston and the block. ARP2000 bolts cost little compared with rebuilding a K20A bottom end.

Matching connecting rod bearings

To complete the bottom-end rebuild, we offer the connecting rod bearings intended for this engine.

Honda K20A connecting rod bearings →

  • Brand
    ARP
  • Reference
    ARP-208-6003
  • EAN13
    0672036032449

16 other products in the same category

Viewed products

Loading...