Skip to content
  • In stock
Reinforced head gasket Honda K20A K20Z1 K24A1 - C4311-030 Reinforced head gasket Honda K20A K20Z1 K24A1 - C4311-030 Reinforced head gasket Honda K20A K20Z1 K24A1 - C4311-030 Reinforced head gasket Honda K20A K20Z1 K24A1 - C4311-030

Reinforced head gasket Honda 2.0 2.4 16V i-VTEC K20A K20Z1 K24A1

€113.59 (tax incl.)
€151.45 (tax incl.) -25%

Reinforced Athena and Cometic head gasket, in Cut Ring, MLS and MLX for K20A and K20Z1. Sold individually.

  • Brands: Athena, Cometic
  • Engines: K20A, K20A1, K20A2, K20A3, K20A4, K20A5, K20A9, K20Z1, K24A1
  • Bores: 86 to 90 mm
  • Thicknesses: 0.46 to 3.56 mm
C4311-030
1 in stock in Europe (72h lead time)
Pay in installments

The Honda engines covered

The Honda K20A is the 2.0-litre 16-valve DOHC i-VTEC inline four-cylinder petrol engine of the Civic, Integra, Accord, CR-V, FR-V and Stream, and of the Acura RSX; the K24A1 is its 2.4-litre version in the CR-V. This page covers the K20A, K20A1, K20A2, K20A3, K20A4, K20A5, K20A9, K20Z1 and K24A1: these engines take the same reinforced cylinder head gaskets.

The original gasket carries part number 12251-PNA-004, or 12251-PNC-003, 12251-PN3-0031 and 12251-PRB-A01 depending on the version. It is a multi-layer steel (MLS) gasket with a 86.5 mm bore, whose thickness Honda does not publish. It is sized for standard combustion pressure: when that pressure rises, clamping load drops, the cylinder head lifts, and coolant passes into a cylinder.

Reinforced cylinder head gaskets

A cylinder head gasket does not create the seal on its own: it holds because the fasteners clamp the head against the block. A composite gasket is crushed for good beyond 100 N/mm² of admissible stress, whereas the 301 stainless steel of the MLS and MLX gaskets withstands 517 N/mm², 5 times more, and springs back at every combustion.

This page brings together the part numbers from two racing manufacturers, Athena and Cometic, in four constructions: Athena Cut Ring with stainless rings, Athena MLS with Gas Stopper, Cometic MLS multi-layer steel and Cometic MLX with a chamber stopper. Gasket bores run from 86 to 90 mm, covering the standard block as well as the rebored block, and thicknesses from 0.46 to 3.56 mm, enough to adjust the compression ratio without touching the pistons or the cylinder head. As a rule, the gasket bore chosen is at least 0.5 mm larger than the actual cylinder bore. Each part number is sold individually, one gasket per engine.

Technical specifications

Gasket bore
OEM 86.5 mm
Thickness Gasket volume Gasket type
OEM MLS
Brand Part number
OEM 12251-PNA-004
86 mm 0.46 mm 2.67 MLS Cometic C4300-018
86 mm 0.69 mm 4.01 MLS Cometic C4300-027
86 mm 0.76 mm 4.41 MLS Cometic C4300-030
86 mm 0.91 mm 5.29 MLS Cometic C4300-036
86 mm 1.02 mm 5.92 MLS Cometic C4300-040
86 mm 1.14 mm 6.62 MLS Cometic C4300-045
86 mm 1.30 mm 7.55 MLS Cometic C4300-051
86 mm 1.42 mm 8.25 MLS Cometic C4300-056
86 mm 1.52 mm 8.83 MLS Cometic C4300-060
86 mm 1.68 mm 9.76 MLS Cometic C4300-066
86 mm 1.78 mm 10.34 MLS Cometic C4300-070
86 mm 1.91 mm 11.09 MLS Cometic C4300-075
86 mm 2.03 mm 11.79 MLS Cometic C4300-080
86 mm 2.13 mm 12.37 MLS Cometic C4300-084
86 mm 2.18 mm 12.66 MLS Cometic C4300-086
86 mm 2.34 mm 13.59 MLS Cometic C4300-092
86 mm 2.49 mm 14.46 MLS Cometic C4300-098
86 mm 3.05 mm 17.72 MLS Cometic C4300-120
86 mm 3.56 mm 20.68 MLS Cometic C4300-140
86.5 mm 0.76 mm 4.47 MLS Cometic C14079-030
87 mm 0.69 mm 4.10 MLS Cometic C4311-027
87 mm 0.76 mm 4.52 MLS Cometic C4311-030
87 mm 0.85 mm 5.05 MLS Athena 338430R
87 mm 0.91 mm 5.41 MLS Cometic C4311-036
87 mm 1.02 mm 6.06 MLS Cometic C4311-040
87 mm 1.14 mm 6.78 MLS Cometic C4311-045
87 mm 1.30 mm 7.73 Cut Ring Athena 330188R
87 mm 1.30 mm 7.73 MLS Cometic C4311-051
87 mm 1.42 mm 8.44 MLS Cometic C4311-056
87 mm 1.52 mm 9.04 MLS Cometic C4311-060
87 mm 1.68 mm 9.99 MLS Cometic C4311-066
87 mm 1.78 mm 10.58 MLS Cometic C4311-070
87 mm 1.91 mm 11.35 MLS Cometic C4311-075
87 mm 2.03 mm 12.07 MLS Cometic C4311-080
87 mm 2.18 mm 12.96 MLS Cometic C4311-086
87 mm 2.34 mm 13.91 MLS Cometic C4311-092
87 mm 2.49 mm 14.80 MLS Cometic C4311-098
87 mm 3.05 mm 18.13 MLS Cometic C4311-120
87 mm 3.56 mm 21.16 MLS Cometic C4311-140
87.5 mm 0.76 mm 4.57 MLS Cometic C14039-030
87.5 mm 0.91 mm 5.47 MLS Cometic C14039-036
87.5 mm 1.30 mm 7.82 MLS Cometic C14039-051
88 mm 0.58 mm 3.53 MLS Cometic C4312-023
88 mm 0.69 mm 4.20 MLS Cometic C4312-027
88 mm 0.76 mm 4.62 MLS Cometic C4312-030
88 mm 0.91 mm 5.53 MLS Cometic C4312-036
88 mm 1.00 mm 6.08 Cut Ring Athena 330169R
88 mm 1.02 mm 6.20 MLS Cometic C4312-040
88 mm 1.14 mm 6.93 MLS Cometic C4312-045
88 mm 1.30 mm 7.91 MLS Cometic C4312-051
88 mm 1.42 mm 8.64 MLS Cometic C4312-056
88 mm 1.52 mm 9.24 MLS Cometic C4312-060
88 mm 1.68 mm 10.22 MLS Cometic C4312-066
88 mm 1.78 mm 10.83 MLS Cometic C4312-070
88 mm 1.91 mm 11.62 MLS Cometic C4312-075
88 mm 2.03 mm 12.35 MLS Cometic C4312-080
88 mm 2.13 mm 12.95 MLS Cometic C4312-084
88 mm 2.18 mm 13.26 MLS Cometic C4312-086
88 mm 2.34 mm 14.23 MLS Cometic C4312-092
88 mm 2.49 mm 15.14 MLS Cometic C4312-098
88 mm 3.05 mm 18.55 MLS Cometic C4312-120
88 mm 3.56 mm 21.65 MLS Cometic C4312-140
88.5 mm 0.85 mm 5.23 MLS Athena 338411R
89 mm 0.69 mm 4.29 MLS Cometic C4313-027
89 mm 0.76 mm 4.73 MLS Cometic C4313-030
89 mm 0.81 mm 5.04 MLX Cometic C4596-032
89 mm 0.91 mm 5.66 MLS Cometic C4313-036
89 mm 0.91 mm 5.66 MLX Cometic C4596-036
89 mm 1.02 mm 6.35 MLS Cometic C4313-040
89 mm 1.02 mm 6.35 MLX Cometic C4596-040
89 mm 1.07 mm 6.66 MLX Cometic C4596-042
89 mm 1.12 mm 6.97 MLX Cometic C4596-044
89 mm 1.14 mm 7.09 MLS Cometic C4313-045
89 mm 1.22 mm 7.59 MLX Cometic C4596-048
89 mm 1.27 mm 7.90 MLX Cometic C4596-050
89 mm 1.30 mm 8.09 MLS Cometic C4313-051
89 mm 1.32 mm 8.21 MLX Cometic C4596-052
89 mm 1.52 mm 9.46 MLS Cometic C4313-060
89 mm 1.68 mm 10.45 MLS Cometic C4313-066
89 mm 1.78 mm 11.07 MLS Cometic C4313-070
89 mm 1.91 mm 11.88 MLS Cometic C4313-075
89 mm 2.03 mm 12.63 MLS Cometic C4313-080
89 mm 2.13 mm 13.25 MLS Cometic C4313-084
89 mm 2.18 mm 13.56 MLS Cometic C4313-086
89 mm 2.34 mm 14.56 MLS Cometic C4313-092
89 mm 2.49 mm 15.49 MLS Cometic C4313-098
89 mm 3.05 mm 18.97 MLS Cometic C4313-120
89 mm 3.56 mm 22.15 MLS Cometic C4313-140
89.5 mm 0.85 mm 5.35 MLS Athena 338468R
90 mm 0.76 mm 4.83 MLS Cometic H1912SP1030S
90 mm 0.76 mm 4.83 MLS Cometic C14055-030
90 mm 1.02 mm 6.49 MLS Cometic H1912SP1040S
90 mm 1.02 mm 6.49 MLS Cometic C14043-040
90 mm 1.14 mm 7.25 MLS Cometic H1912SP1045S
90 mm 1.52 mm 9.67 MLS Cometic C14043-060

Gasket volume: the space the gasket leaves above each cylinder. It enlarges the combustion chamber, and the larger it is, the lower the compression ratio. Values compare with one another at identical gasket bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts
90005-PNA-003, M11 x 155
K20A, K20A1, K20A2, K20A3, K20A4, K20A5, K20A9, K20Z1, K24A1 39 Nm, then 90°, then 90° (a further 90° for new bolts)
ARP cylinder head studs
ARP-208-4701
K20A2, K20A3 36 Nm, then 72 Nm, then 108 Nm

Before fitting, check the flatness of the cylinder head and of the block with a straight edge and have them skimmed if necessary. None of these gaskets requires sealant: Athena and Cometic both supply them already coated.

Reinforced ARP cylinder head studs K20A2 K20A3 →

Technical guide

The three constructions offered

Athena Cut Ring cylinder head gasket Athena Cut Ring
A gasket in reinforced, asbestos-free MO115 material (steel core, aramid fibres, NBR binder), supplied with separate AISI 304 stainless steel rings around each cylinder. Athena also intends it for turbocharged or nitrous engines above 2 bar, with no machining of the cylinder head or block. A silicone bead reinforces the sealing of the water and oil passages. On fitting, the ring embossments face the cylinder head. Athena rates the MO115 material at 100 N/mm² at most: the stainless rings are what hold combustion.
Athena MLS cylinder head gasket Athena MLS
Two to five layers of AISI 301 stainless steel, laser cut, stamped and riveted. Around each cylinder, a layer folded over on itself, the Gas Stopper, concentrates the clamping load on the combustion chamber, while beads seal the water and oil passages. The outer layers receive a two-coat finish: the first withstands high temperatures and fills small irregularities on the block and cylinder head, the second, silicone based, keeps the gasket from sticking on disassembly. This is Athena's all-steel choice, from a prepared naturally aspirated engine to moderate forced induction.
Cometic MLS cylinder head gasket Cometic MLS
Several stamped and riveted stainless steel layers. The outer layers carry active beads around each cylinder and each fluid passage. Sealing is achieved with a moderate clamping load and limited bore distortion. This is the versatile choice, from a prepared naturally aspirated engine to light forced induction.
Cometic MLX cylinder head gasket Cometic MLX
The same base as the MLS, with a folded centre layer forming a stopper around the combustion chamber and a high-temperature coating. Local clamping increases without adding bore distortion. It is the most resistant of the all-steel gaskets, to be chosen when boost goes beyond what an MLS can hold, in 89 mm.

Choosing bore and thickness

Gasket bore. The Athena Cut Ring comes in 87 and 88 mm, the Athena MLS in 87, 88.5 and 89.5 mm, the Cometic MLS in 86, 86.5, 87, 87.5, 88, 89 and 90 mm, the Cometic MLX in 89 mm.

Thickness. Honda does not publish the thickness of the original gasket. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio The value closest to the thickness of the removed gasket
Skimmed cylinder head, make up the lost height The thickness of the removed gasket + what was removed
Forced induction build, lower the ratio A thickness above that of the removed gasket
Naturally aspirated build, raise the ratio A thickness below that of the removed gasket

With a thickness finer than that of the removed gasket, measure piston protrusion above the block with a dial gauge: it is what determines the remaining clearance between piston and cylinder head.

The two brands

Athena Athena S.p.A. is an Italian manufacturer of engine gaskets and components, with its head office and main plant in Alonte, in the Veneto region. The group also produces in Spain, the United States, Brazil and India. Its multi-layer gaskets are fitted as original equipment by car manufacturers, and its racing range is designed and made entirely in Italy.
Cometic Cometic Gasket, Inc. is an American manufacturer of engine gaskets and sealing solutions, founded in 1989 and based in Concord, Ohio. Its speciality is the made-to-order gasket, in the bore and thickness required. All its products are made in the United States, from American materials.

Advantages over the original gasket

Criterion Original gasket 12251-PNA-004 Reinforced gaskets
Construction Multi-layer steel (MLS) Multi-layer stainless steel
Gasket bore 86.5 mm 86 to 90 mm
Thicknesses available Not published by Honda 0.46 to 3.56 mm, 28 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the 86.5 mm bore of the original gasket covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Acura RSX (DC) K20A 220 hp 2001-2006
Acura RSX (DC) K20A2 203 hp 2001-2006
Acura RSX (DC) K20A3 158, 160 and 162 hp 2001-2006
Honda Accord VII (CL, CN) K20A 218 and 220 hp 2003-2008
Honda Civic VII (EP, ES, ET, EU, EV) K20A 215 hp 2000-2005
Honda Civic VII (EP, ES, ET, EU, EV) K20A2 200 hp 2001-2005
Honda Civic VII (EP, ES, ET, EU, EV) K20A3 155, 160 and 162 hp 2001-2006
Honda Civic VIII (FD, FA) K20A3 155 hp 2006-2012
Honda Civic VIII (FD, FA) K20A5 224 hp 2007-2010
Honda CR-V II (RD) K20A 158 hp 2003-2005
Honda CR-V II (RD) K20A4 150 and 156 hp 2001-2007
Honda CR-V II (RD) K20A5 152 and 156 hp 2002-2007
Honda CR-V II (RD) K24A1 152, 156, 160 and 162 hp 2001-2007
Honda FR-V (BE) K20A9 150, 155 and 156 hp 2004-2011
Honda Integra Coupé (DC5) K20A2 200 hp 2004-2008
Honda Integra Coupé (DC5) K20A3 160 hp 2002-2008
Honda Integra Coupé (DC5) K20Z1 209 and 220 hp 2002-2007
Honda Stepwgn (RF) K20A9 160 hp 2000-2005
Honda Stream (RN) K20A 158 hp 2001-2006
Honda Stream (RN) K20A1 156 hp 2001-2006
Honda Stream (RN) K20A5 156 hp 2001-2006

OEM part number: 12251-PNA-004, 12251-PNC-003, 12251-PN3-0031, 12251-PRB-A01.

Important: the K24A, K24A2, K24A3 and K24Z1 of the Accord and Acura TSX, the K24 of later generations, the K20C and the K20Z3 take other cylinder head gaskets: they are not covered by this page.

Why switch to a reinforced gasket?

A reinforced gasket holds where the standard one reaches its limit: at higher combustion pressure it keeps its shape instead of being crushed.

As soon as power goes up, turbo, supercharger or raised compression ratio, the head gasket becomes the weak link of the top end. Switching to a reinforced gasket is then not a comfort but a safeguard: it is what prevents the failure and the head removal that comes with it.

16 other products in the same category

Viewed products

Loading...