- In stock
Tri-metal crankshaft main bearings Honda Acura B16 B17 B18 B20 K20 K24
Set of 10 tri-metal crankshaft main bearing shells for Honda and Acura B16, B17, B18, B20, K20, K24.
- Brands and treatments : ACL Race (with or without Calico) and King Racing (XPC)
- Compatibility : Civic, CRX, Integra, Accord, CR-V, Element, Odyssey, Acura RSX (partial list)
- Available sizes : standard to +0.50 mm, increased clearance versions (HX / STDX)
The Honda and Acura B16, B17, B18, B20, K20 and K24 engines
This main bearing set is listed by ACL for the Honda and Acura B16, B17, B18, B20, K20 and K24 engine families, including the Honda Civic, CRX, Integra, Accord, CR-V, Element and Odyssey and the Acura Integra and RSX. ACL and King list a main bearing set for these engines.
The crankshaft of these engines runs on five main bearings. Each journal turns between two half shells, one seated in the block and the other in the main bearing cap: they carry the crankshaft. The ACL Race Series and KING RACING tri-metal sets shown here replace them on built engines.
Tri-metal main bearings
In a trimetal bearing, a steel back carries a copper-lead intermediate layer with high load capacity, itself covered by an anti-friction running layer that spares the main journal. The set is supplied complete: 0 half shells, i.e. The complete set contains 10 half shells, five pairs for five main bearings. The upper and lower half shells are different: each goes in its own position.
Trimetal targets high, sustained loads, whereas aluminium bi-metal is limited to low to medium loads: about 8,000 psi for the latter, up to 12,000 psi for a performance trimetal, 50% more. The benefit shows in strength and durability on turbo, supercharged and high-revving engines.
Technical specifications
| ACL bearings Crankshaft journal Ø 54.980 / 55.000 mm Housing bore Ø 59.000 / 59.020 mm Width 20 mm | King bearings Crankshaft journal Ø 54.976 / 54.999 mm Housing bore Ø 58.999 / 59.019 mm Width 20 mm |
| Reference | Brand and treatment | Size | Wall thickness (mm) |
|---|---|---|---|
| 5M1959H-STD | ACL Race - Untreated | Standard | 2.002 |
| 5M1959HX-STD | ACL Race - Untreated | Std, increased clearance (HX) | 1.989 |
| 5M1959H-.025 | ACL Race - Untreated | +0.025 | 2.0145 |
| 5M1959H-.25 | ACL Race - Untreated | +0.25 | 2.127 |
| 5M1959HC-STD | ACL Race - Calico | Standard | |
| 5M1959HXC-STD | ACL Race - Calico | Std, increased clearance (HX) | |
| MB5259XPC | King Racing - pMaxKote | Standard | 2.004 |
| MB5259XPC STDX | King Racing - pMaxKote | Std, increased clearance (STDX) | 1.991 |
| MB5259XPC.026 | King Racing - pMaxKote | +0.026 | 2.017 |
| MB5259XPC0.25 | King Racing - pMaxKote | +0.25 | 2.131 |
| MB5259XPC0.5 | King Racing - pMaxKote | +0.50 | 2.258 |
Running clearance
Running clearance is the gap between the bearing and the main journal, filled by the oil film.
While the engine turns, the main journal floats on this oil film, which carries the load without direct contact with the bearing. Film thickness depends on clearance: too tight, oil passes poorly, temperature rises and the risk of seizure grows; too wide, oil escapes, the film carries less and oil pressure decreases. A correct clearance ensures both sufficient lubrication and a well-maintained film.
| Size / grade | When to choose it | ACL Race Series | King XPC |
|---|---|---|---|
| Standard (STD) | Standard journal, not reground | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
| Increased clearance (HX / STDX) | Wider clearance: high oil flow, high rpm | 0.082 to 0.093 mm | 0.080 mm - 0.093 mm |
| +0.025 / +0.026 mm | Polished journal | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
| +0.25 mm | Journal reground to 0.25 mm | 0.057 to 0.068 mm | 0.055 mm - 0.068 mm |
| +0.50 mm | Journal reground to 0.50 mm | 0.055 mm - 0.068 mm |
Check at assembly: lay a calibrated strip (Plastigauge) on the journal, tighten the main cap following the manufacturer's procedure, then compare the width of the crushed strip with the gauge to read the clearance.

Technical guide
These ACL and King trimetal main bearings are aimed at built engines and racing: where a standard bearing quickly reaches its limit, they accept more power, more rpm and more boost. The range includes the standard size, a +0.025 / +0.026 mm size for a main journal that has only been polished, +0.25 and +0.50 mm regrind sizes and the HX / STDX version with increased clearance for high-revving engines or engines needing a high oil flow. It allows the same part number to be kept after the crankshaft is reground and the clearance to be tailored to the oil used and the engine's duty.
The two brands
![]() |
An Australian specialist in high-performance engine bearings since 1949, ACL Bearing Company produces the Race Series: precisely made trimetal bearings, available in numerous sizes and recognised on built engines across the world. |
![]() |
King Engine Bearings, an Israeli manufacturer of high-performance engine bearings since the 1960s, offers with its pMax Black tri-metal alloy bearings designed for heavy loads, with a pMaxKote coating (XPC version). |
Construction and advantages
| Criterion | ACL Race Series | King Racing |
| Cross-section | ![]() |
![]() |
| Type | High-performance trimetal bearing | High-performance trimetal bearing |
| Country of manufacture | Australia | Israel |
| Construction | Trimetal: steel back, copper layer, soft surface | Trimetal: steel back, copper layer, soft surface |
| Alloy | Race Series (copper-lead) | pMax Black (hardened copper-lead) |
| Protective coating | Calico CT-1 (HC and HXC versions): thin dry-film lubricant that reduces friction and wear. No coating on the H and HX versions. | pMaxKote (XPC version): polymer coating on the surface that limits wear when lubrication drops (start-ups, thin oil film). |
| Available sizes | Standard to +0.25 mm (+ increased clearance HX) ; Calico: standard and HXC | Standard to +0.50 mm (+ increased clearance STDX) |
Vehicle compatibility
This main bearing set fits the Honda and Acura B16, B17, B18, B20, K20 and K24 engines of the following vehicles:
| Brand | Model (chassis) | Engine code | Power | Years |
|---|---|---|---|---|
| HONDA | CR-V III (RE_) 2.4 i-VTEC / 2.4 i-VTEC 4WD | K24A1, K24Z1 | 160–170 hp | 2006–2012 |
| HONDA | ACCORD VII (CL, CN) 2.4 i 16V / 2.4 Vtec / 2.4 (CL9) | K24A3, K24A4, K24A8 | 143–190 hp | 2003–2008 |
| HONDA | ACCORD VII Tourer (CM, CN) 2.4 (CM2) / 2.4 Vtec T | K24A1, K24A3 | 190–200 hp | 2003–2008 |
| HONDA | CR-V II (RD_) 2.4 / 2.4 Vtec / 2.4 4WD | K24A1 | 152–162 hp | 2001–2007 |
| HONDA | ACCORD VII (CM, UC) 2.4 Vtec E (CM5) | K24A4, K24A8 | 160–170 hp | 2002–2008 |
| HONDA | STEPWGN (LA-RF_, UA-RF_) 2.4 / 2.4 4WD | K24A3 | 162 hp | 2000–2005 |
| HONDA | STEPWGN (DBA-RG_) 2.4 Z FF / 2.4 Z FF 4WD | K24A3 | 162 hp | 2005–2009 |
| HONDA | ODYSSEY (RL1, RA6, RA_) 2.4 / 2.4 4WD | K24A4 | 190 hp | 2003– |
| HONDA | ACCORD Coupe (CM) 2.4 (CM7) | K24A4, K24A8 | 160–169 hp | 2003–2008 |
| HONDA | ELEMENT (YH) 2.4 / 2.4 4WD | K24A4, K24A8 | 158–169 hp | 2002–2011 |
| HONDA | ELYSION (RR) 2.4 i-VTEC / 2.4 i-VTEC 4WD | K24A1 | 160 hp | 2004– |
| HONDA | ODYSSEY (RL3, RL4, RB) 2.4 (RB3, RB1) | K24A3 | 200 hp | 2004–2008 |
| HONDA | CR-V IV (RM_) 2.4 i-VTEC / 2.4 i-VTEC 4WD | K24A1 | 170–185 hp | 2012– |
| HONDA | FR-V (BE) 2.4 (BE8) | K24A3 | 162 hp | 2006–2011 |
| HONDA | INTEGRA Coupé (DC) 1.8 VTiR (DC2) / 1.8 Type-R (DC2) | B18C1, B18C2, B18C7 | 170–200 hp | 1993–2001 |
| ACURA | INTEGRA Hatchback 1.8 | B18C5 | 197 hp | 1996–2001 |
| HONDA | CIVIC IV Hatchback (EC, ED, EE, EF) 1.6 i 16V Vtec (EE9) | B16A1 | 150 hp | 1989–1991 |
| HONDA | CRX II (ED, EE) 1.6 i 16V Vtec (EE8) | B16A1 | 150 hp | 1989–1992 |
| HONDA | CRX III (EH, EG) 1.6 i VTi (EG2) | B16A2, B16A3 | 160 hp | 1992–1998 |
| HONDA | CIVIC V Hatchback (EG, EH) 1.6 VTi 16V (EG6) | B16A2 | 160 hp | 1991–1995 |
| HONDA | CIVIC V Saloon (EG, EH) 1.6 VTi (EG9) | B16A2 | 160 hp | 1991–1995 |
| HONDA | CIVIC VI Hatchback (EJ, EK) 1.6 VTi (EK4) | B16A2 | 160 hp | 1995–2001 |
| HONDA | CIVIC VI Saloon (EJ, EK, SO) 1.6 VTi (EK4, SO4) | B16A2 | 160 hp | 1995–2001 |
| HONDA | CIVIC VI Coupé (EJ, EM1) 1.6 i Vtec (EM1) | B16A2 | 160 hp | 1999–2000 |
| HONDA | CIVIC IV Saloon (ED, EF) 1.6 4x4 | B16A1 | 150 hp | 1988–1991 |
| HONDA | INTEGRA Hatchback (DA) 1.8 (DA9) | B18A1, B18B1 | 131 hp | 1989–1993 |
| HONDA | INTEGRA Coupé (DC) 1.8 (DC2) | B18B1, B18B2 | 137–146 hp | 1993–2001 |
| HONDA | INTEGRA Saloon (DB6, DB7, DB8, DB9) 1.8 ESI (DB7) | B18B2 | 145 hp | 1993–2001 |
| HONDA | INTEGRA Saloon (DA5, DA6, DA7, DA8, DA9, DB1, DB2) 1.8 (DB1) | B18A2 | 140 hp | 1989–1993 |
| ACURA | INTEGRA Hatchback 1.8 / 1.7 | B17A1, B18A1, B18B1 | 132–162 hp | 1990–2001 |
| ACURA | INTEGRA Saloon 1.8 | B18A1, B18B1 | 132–144 hp | 1990–2001 |
| HONDA | CR-V I (RD) 2.0 4WD (RD1) / 2.0 (RD2) / 2.0 | B20B4, B20Z2 | 128–148 hp | 1996–2001 |
| HONDA | CIVIC VII Hatchback (EU, EP, EV) 2.0 i Sport (EV1) / 2.0 (EV1) | K20A3 | 160–162 hp | 2001–2005 |
| HONDA | CIVIC VII Saloon (ES, ET) 2.0 (ET1) / 2.0 iVtec (ET1) | K20A3 | 155–160 hp | 2003–2006 |
| HONDA | CIVIC VIII Saloon (FD, FA) 2.0 (FD2) | K20A3 | 155 hp | 2006–2012 |
| HONDA | INTEGRA Coupé (DC5) 2.0 (DC5) | K20A3 | 160 hp | 2002–2008 |
| ACURA | RSX Coupé (DC_) 2.0 / 2.0 Sport | K20A3 | 158–162 hp | 2001–2006 |
Why replace the bearings
Replacing the bearings during a build or rebuild guards against the most expensive failure: a worn-out main bearing scores the main journal, contaminates the oil circuit with debris and forces at least a crankshaft regrind, or even block repairs. Against such costs a new set weighs little: it is the cheapest part of the crankshaft assembly, but the one whose failure costs the most.
-
Brand
-
Reference5M1959H-STD



