- On order
Reinforced inlet valves TOYOTA 4A-GE 20V
Set of 12 reinforced inlet valves for the TOYOTA 4A-GE 20V.
- Brands: FERREA, SUPERTECH
- Engine: 4A-GE (20V)
- Dimensions: 26.5 mm or 27.5 mm head, 4.98 mm stem
- Material: EV8 stainless or black nitrided stainless
TOYOTA engines covered
The 20-valve 4A-GE is Toyota's 1.6 litre four-cylinder with twin overhead camshafts and five valves per cylinder. From 1987 to 2001 it powered the Corolla E9, E10 and E11, the Corolla Levin, the Sprinter and the Carina VII, from 139 to 165 hp.
Each cylinder has three inlet valves, 12 per engine, with a slim stem. A sharper camshaft, a higher rev limit or stiffer springs load them well beyond stock use.
FERREA and SUPERTECH reinforced inlet valves
On the 20-valve 4A-GE, each of the 12 inlet valves snaps open and shut at a frantic pace once the engine starts revving, admitting fresh air into the cylinder. As it closes, its head knocks against the seat, while its slim stem keeps sliding back and forth. These valves operate at 400 to 550 °C, where an ordinary chrome-silicon steel is already fading: 500 MPa at 500 °C, then 250 MPa at 600 °C, only 100 °C higher: half its strength gone. A more aggressive cam profile, stiffer springs or more revs make the shocks, friction and heat worse again.
The FERREA F6332 from the 6000 series is made of EV8 stainless, its stem hard-chromed. This steel retains 650 MPa at 500 °C and 550 MPa at 600 °C, 30 % then 120 % better than chrome-silicon, and the hard chrome lets the stem glide without wearing. Both SUPERTECH parts, TIVN-1017-12 and TIVN-1018-12, are stainless with black nitriding, a treatment that hardens the stem's outer layer so it wears more slowly in the guide. The engine therefore gets two stem treatments; FERREA stays at the original size, while SUPERTECH also exists with an enlarged head.
One enlarged head is available, the stem remaining at 4.98 mm: 27.5 mm (+1 mm, SUPERTECH), compared with 26.5 mm at the original size. Air crosses the seat more freely, every cylinder inhales a bigger charge and the engine gains from it, as long as all 12 inlet seats are cut to that diameter.
Inlet valve technical specification
| Part number | Brand | Size | Head Ø | Stem Ø | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| F6332*12 | FERREA | Standard | 26.5 mm | 4.98 mm | 98.42 mm | EV8 stainless steel, hard chrome stem | |
| TIVN-1017-12 | SUPERTECH | Standard | 26.5 mm | 4.98 mm | 98.6 mm | Stainless steel, black nitrided | |
| TIVN-1018-12 | SUPERTECH | +1 mm | 27.5 mm | 4.98 mm | 98.6 mm | Stainless steel, black nitrided |
Fitting details
| Part | TOYOTA original | Reinforced |
|---|---|---|
| Collets | K10106 | |
| Valve stem seals | ||
| Valve guide | GDE-T20V-I-12 |
FERREA pairs this engine with its K10106 collets, for a 5 mm stem; SUPERTECH offers the GDE-T20V-I-12 inlet guide for it.
The 27.5 mm TIVN-1018-12 needs inlet seats machined to its size; the 26.5 mm valves fit seats reconditioned to factory size.
Technical guide
The brands offered
| FERREA Racing Components started out in 1978 in Fort Lauderdale, Florida, under the lead of two Argentinian tuners who still oversee every production step. A FERREA valve begins as a one-piece forged blank, then taken over by CNC machining centres; it equips NASCAR engines, dragsters and circuit cars. | |
| SUPERTECH Performance, a San Jose firm serving motorsport for over three decades, designs its valvetrain items one engine at a time. Each part goes under ultrasound, X-rays and laser beam before being shipped to tuners. |
How to choose
Seated in the groove under the upper retainer, the collets hold the valve. On the 20-valve 4A-GE, you settle the head size before the material and finish.
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Original size, 26.5 mm For a 20-valve 4A-GE head whose inlet seats keep their factory dimension, simply refurbished. FERREA and SUPERTECH both offer it; fitting is done as with the stock valve, with no seat rework. |
Enlarged head, 27.5 mm A wider head lets more air past the seat, around 10 to 12 cfm for each extra millimetre, which improves the supply to each cylinder. The 12 seats must be machined to 27.5 mm; this is also the answer for seats already reground. Offered by SUPERTECH. |
| Material | FERREA 6000 series EV8 stainless, hard-chromed stem, designed to cope with the fiercest heat, in original size only. For this engine FERREA provides its K10106 collets, suited to the 5 mm stem, to be added to the order. |
SUPERTECH Black nitrided stainless: this treatment shields the stem from friction in the guide, in original size as well as with the 27.5 mm head. SUPERTECH also offers its GDE-T20V-I-12 inlet guide for this engine, worth planning for a full rebuild. |
When reinforced valves become necessary
- Fitting sharper camshafts, with firmer valve springs
- Higher rev limit
- Turbo or supercharger grafted onto the 20-valve 4A-GE
- Head prepared for track, rallies or hill climbs
- Tired stock valves or seats already reground
Compatible vehicles
| Model | Engine code | Power | Years |
|---|---|---|---|
| Carina VII (T21) 1.6, 1.6 GT (AT210) | 4A-GE (20V) | 165 hp | 1996-2001 |
| Corolla, Corolla Liftback (E9) 1.6 i 20V (AE92) | 4A-GE (20V) | 139 hp | 1987-1991 |
| Corolla (E10) 1.6 i 20V (AE101) | 4A-GE (20V) | 159 hp | 1991-1998 |
| Corolla (E10) 1.6 (AE101G) | 4A-GE (20V) | 165 hp | 1996-1998 |
| Corolla (E11) 1.6 i 20V (AE111) | 4A-GE (20V) | 156 hp | 1998-2000 |
| Corolla Levin (E10) 1.6 GT (AE101) | 4A-GE (20V) | 160 hp | 1991-1997 |
| Corolla Levin (E11) 1.6 (AE111) | 4A-GE (20V) | 165 hp | 1995-2000 |
| Sprinter (E1) 1.6 (AE101) | 4A-GE (20V) | 160 hp | 1991-1995 |
| Sprinter (E1) 1.6 (AE111) | 4A-GE (20V) | 165 hp | 1997-2000 |
Related products
20-valve 4A-GE head on the bench: renew its 8 exhaust valves and all the stem seals as well. The exhaust set intended for this engine can be found here:
| Exhaust valves TOYOTA 4A-GE 20V → |
-
Brand
-
ReferenceF6332*12