Skip to content
  • In stock
Toyota 7MGTE Soupape échappement inconel SUPERTECH 28x5.97x98.20mm Toyota 7MGTE Soupape échappement inconel SUPERTECH 28x5.97x98.20mm

Reinforced inlet valves VAG 1.8T 20V

€356.31 (tax incl.)
€445.39 (tax incl.) -20%

Set of 12 reinforced inlet valves for the VAG group 1.8 T 20V: AUDI A3, S3, A4, A6, TT, VOLKSWAGEN Golf IV, Bora, New Beetle, Passat B5, SEAT Leon, Ibiza, SKODA Octavia, Superb.

  • Brands: SUPERTECH, FERREA
  • Engines: AUDI, VOLKSWAGEN, SEAT, SKODA 1.8 T 20V
  • Dimensions: 26.9 or 27.9 mm head, 6 mm stem
  • Material: black nitride stainless steel (SUPERTECH), Competition Plus (FERREA), 1 or 3 grooves
AIVN-1103-12
3 in stock in Europe (72h lead time)
Available in stock in Europe (72h lead time)
Pay in installments

The VAG engines covered

The 1.8 T 20V is Audi's 1,781 cc turbocharged four-cylinder, with a five-valve-per-cylinder head: three inlet, two exhaust. From 1995 to 2009 it powers the A3 and S3 8L, the A4 B5, B6 and B7, the A6 C5 and the TT 8N, from 150 to 245 hp. The same engine, shared across the Volkswagen group (VAG), powers the Volkswagen Golf IV GTI, Bora, New Beetle, Passat B5, Polo GTI and Sharan (150 to 180 hp), the SEAT Leon and Leon Cupra R, Ibiza Cupra and FR, Cordoba Cupra, Toledo and Alhambra (150 to 225 hp), and the SKODA Octavia I, its RS version and the Superb I (150 to 180 hp).

Each engine takes 12 original 058 109 601 C inlet valves: 26.9 mm head, 6 mm stem, 105.1 mm length. These small valves work under boost pressure; a remap, a bigger turbo or sharper camshafts ask far more of them than stock use.

SUPERTECH and FERREA reinforced inlet valves

The 1.8 T 20V uses three inlet valves per cylinder, twelve in all, to meter the air the turbo forces into the chambers. At high revs each valve leaves its seat and hammers back onto it at a rate counted in dozens per second, while its stem travels endlessly through the guide. Operating temperature is 400 to 550 °C, where the stock chrome-silicon steel is already losing ground: 500 MPa at 500 °C, barely 250 MPa at 600 °C, just above, i.e. 50 % less. Extra lift, stiffer springs, more revs or higher boost on the 1.8 T multiply impacts, friction and heat.

These reinforced valves use a chrome-nickel competition stainless from the EV8 family (21-4N), able to keep 650 MPa at 500 °C, 30 % above stock, and 550 MPa at 600 °C, 120 % above. On SUPERTECH parts, the stem is hardened and polished by black nitriding, so it rubs and wears less in the guide. FERREA's F1556P and F1557P come from the Competition Plus range, credited by the brand with 20 % extra strength in heat and fatigue, plus 25 % longer seat life; their stem is chromed.

Both brands offer the +1 mm oversize, taking the head from 26.9 to 27.9 mm with stem and length unchanged. Fresh charge then finds a larger opening at the seat, the cylinders charge better and output rises; in return, all twelve inlet seats of the 1.8 T must be recut to that diameter.

Inlet valve technical specification

Part numberBrandSizeHead Ø
OEM 26.9 mm
Stem Ø
OEM 6 mm
Length
OEM 105.1 mm
GroovesMaterial
AIVN-1103-12 SUPERTECH Standard 26.9 mm 6 mm 105.1 mm 3 Black nitride stainless steel
AIVN-1103S-12 SUPERTECH Standard 26.9 mm 6 mm 105.1 mm 1 Black nitride stainless steel
AIVN-1106S-12 SUPERTECH +1 mm 27.9 mm 6 mm 105.1 mm 1 Black nitride stainless steel
F1556P*12 FERREA Standard 26.9 mm 6 mm 105.1 mm 3 Stainless, chrome stem
F1557P*12 FERREA +1 mm 27.9 mm 6 mm 105.1 mm 3 Stainless, chrome stem

AIVN-1103S-12 and AIVN-1106S-12: to be fitted with SUPERTECH KPR-6S/7 collets.

Fitting details

PartOriginalReinforced
Valve collets KPR-VW6-T (3 grooves) / KPR-6S-7 (1 groove)
Valve stem seals 036 109 675 A VS-VBM6I-12 (inlet)
Valve guide 058 103 415 GDE-AU18T-20

The 1-groove AIVN-1103S-12 and AIVN-1106S-12 valves are fitted only with KPR-6S-7 collets. The 3-groove valves, AIVN-1103-12 and FERREA, take 3-groove collets, original or KPR-VW6-T.

The +1 mm size (F1557P*12, AIVN-1106S-12) needs inlet seats cut to 27.9 mm.

These engines use hydraulic tappets: there is no valve clearance to set after the replacement.

Technical guide

Our brands

SUPERTECH San Jose, California, is home to SUPERTECH, which has engineered competition valvetrain components for over 30 years. Its valves are drawn for a given head, verified unit by unit with laser, ultrasound and X-ray, then developed with tuners, from drag cars to the track.
FERREA Founded in Florida in 1978, in Fort Lauderdale, by two tuners of Argentine origin, FERREA Racing Components keeps its entire manufacturing in house. Each valve starts as bar stock forged in one piece, is fully CNC-machined and races in NASCAR as well as in drag and circuit events.

How to choose

Sitting under the upper retainer, collets lock into the stem groove or grooves and hold the valve. The groove count decides how the stem is held in place.

CriterionOption 1Option 2
Size Standard size, 26.9 mm
For a 1.8 T head with all 12 inlet seats at their original diameter: straight fit, no machining. Available from SUPERTECH (3 or single groove) as well as FERREA.
+1 mm oversize, 27.9 mm
The wider seat admits more air, with flow up by about 10 to 12 cfm for every millimetre of head, hence extra power. Seats recut to 27.9 mm, ideally with touched-up ports; also a way to save seats already through a regrind.
Grooves 3 grooves
Original Audi design, the stem stays free to rotate. For a road 1.8 T with springs and revs close to stock; new collets advised (original or KPR-VW6-T). Weak spot: at high revs, impacts load the lowest groove, the thinnest zone of the valve.
Single groove
Here the collets pinch the stem, the groove barely works and the broader contact lowers friction. The valve copes with stiffer springs, high lift and big revs on track, in rally or drag racing. SUPERTECH only; KPR-6S-7 collets essential, preferably new.

When reinforced valves become necessary

  • Sharper cam profiles or stiffer springs
  • Rev cut-out raised higher
  • Higher boost or a larger turbo on the 1.8 T
  • Head overhauled for track, hillclimb or rally
  • Pitted, worn or repair-size original Audi valves

Compatible vehicles

ModelEngine codePowerYears
AUDI A3 (8L1) 1.8 TAGU, AQA, ARZ, AUM / AJQ, APP, ARY, AUQ150-180 hp1996-2003
AUDI A3 (8L1) 1.8 T quattroAGU, ARX, AQA / AJQ, ARY150-180 hp1996-2003
AUDI A3 (8L1) S3 quattroAMK, APY, AUL / BAM210-224 hp1999-2003
AUDI A4 B5 (8D2) 1.8 TAJL / ATW, AEB, AWT, ARK, ANB, APU150-180 hp1995-2000
AUDI A4 B5 (8D2) 1.8 T quattroAJL / ATW, AEB, AWT, ARK, ANB, APU / AWM150-180 hp1995-2001
AUDI A4 B5 Avant (8D5) 1.8 TAEB, AWT, ARK, ANB, APU / AJL150-180 hp1996-2001
AUDI A4 B5 Avant (8D5) 1.8 T quattroAJL / ATW, AEB, AWT, ARK, ANB, APU150-180 hp1996-2001
AUDI A4 B6 (8E2) 1.8 TAMB / AVJ / AWM / BEX / BFB150-190 hp2000-2004
AUDI A4 B6 (8E2) 1.8 T quattroAVJ / AWM, AMB / BEX / BFB150-190 hp2000-2004
AUDI A4 B6 Avant (8E5) 1.8 TAVJ / BEX / BFB150-190 hp2001-2004
AUDI A4 B6 Avant (8E5) 1.8 T quattroAMB / AVJ / AWM / BEX / BFB150-190 hp2001-2004
AUDI A4 B6 Décapotable (8H7) 1.8 TAMB / BFB163-170 hp2002-2005
AUDI A4 B6 Décapotable (8H7) 1.8 T quattroAMB / BFB163-173 hp2003-2005
AUDI A4 B7 (8EC) 1.8 TAMB / BFB163-170 hp2004-2008
AUDI A4 B7 (8EC) 1.8 T quattroBFB163 hp2004-2008
AUDI A4 B7 Avant (8ED) 1.8 TBFB163 hp2004-2008
AUDI A4 B7 Avant (8ED) 1.8 T quattroBFB163 hp2004-2008
AUDI A4 B7 Décapotable (8HE) 1.8 TBFB163 hp2006-2009
AUDI A6 C5 (4B2, 4B4) 1.8 TAEB, AWT, ARK, ANB, APU / AJL150-180 hp1997-2005
AUDI A6 C5 (4B2, 4B4) 1.8 T quattroAEB, AWT, ARK, ANB, APU / AJL150-180 hp1997-2005
AUDI A6 C5 Avant (4B5, 4B6) 1.8 TAEB, AWT, ARK, ANB, APU / AJL150-180 hp1997-2005
AUDI A6 C5 Avant (4B5, 4B6) 1.8 T quattroAEB, AWT, ARK, ANB, APU / AJL150-180 hp1997-2005
AUDI TT (8N3) 1.8 TAJQ, APP, AUQ, AWP, ATC / AUM / AWP / BVP / BVR150-190 hp1998-2006
AUDI TT (8N3) 1.8 T quattroAJQ, ARY, AUQ, ATC / APX, BEA, BAM / AWP / BEA, AMU / BFV / BVR180-245 hp1998-2006
AUDI TT Roadster (8N9) 1.8 TAJQ, APP, AUQ, AWP, ATC / AUM / AWP / BVP / BVR150-190 hp1999-2006
AUDI TT Roadster (8N9) 1.8 T quattroAJQ, ARY, AUQ / APX, BEA, BAM / AWP / BEA, AMU / BVR180-228 hp1999-2006
SEAT ALHAMBRA (7V8, 7V9) 1.8 T 20VAJH, AWC150 hp1997-2010
SEAT CORDOBA (6K1, 6K2) 1.8 T 20V CupraAYP, AQX156 hp2000-2002
SEAT IBIZA II (6K1) 1.8 T 20V CupraAYP, AQX156 hp2000-2002
SEAT IBIZA II (6K1) 1.8 T 20V Cupra RAYP180 hp2000-2002
SEAT IBIZA III (6L1) 1.8 T Cupra RBBU, BLZ180 hp2004-2008
SEAT IBIZA III (6L1) 1.8 T FRBJX, BKV150 hp2003-2008
SEAT LEON (1M1) 1.8 20V TAPP, AUQ180 hp1999-2006
SEAT LEON (1M1) 1.8 20V T 4AJQ, ARY180 hp1999-2006
SEAT LEON (1M1) 1.8 T Cupra RAMK / BAM209-225 hp2002-2006
SEAT TOLEDO II (1M2) 1.8 20VTAPP, AUQ, ARY180 hp2000-2004
SKODA OCTAVIA I (1U2) 1.8 TAGU, ARX, AUM, ARZ150 hp1997-2010
SKODA OCTAVIA I (1U2) 1.8 T 4x4ARX150 hp2001-2006
SKODA OCTAVIA I (1U2) RS 1.8 TAUQ180 hp2001-2006
SKODA OCTAVIA I Combi (1U5) 1.8 TAGU, ARX, AUM, ARZ150 hp1998-2010
SKODA OCTAVIA I Combi (1U5) 1.8 T 4x4ARX150 hp2001-2006
SKODA OCTAVIA I Combi (1U5) RS 1.8 TAUQ180 hp2002-2006
SKODA SUPERB I (3U4) 1.8 TAWT150 hp2001-2008
VW BORA I (1J2) 1.8 TAGU, AWW, AWD, ARX, AUM / AUQ, AWP150-180 hp2000-2005
VW BORA Variant (1J6) 1.8 TAGU, AWW, AWD, ARX, AUM / AUQ, AWP150-180 hp2000-2005
VW GOLF IV (1J1) 1.8 T GTIAGU, ARZ, AWW, AWD, AQA, AUM / AUQ, AWP, BEK150-180 hp1997-2005
VW GOLF IV Variant (1J5) 1.8 TAGU, ARZ, AUM / AUQ150-180 hp2000-2006
VW NEW BEETLE (9C1, 1C1) 1.8 TAGU, APH, AVC, AWU, AWV, BKF / BNU, AWP150-180 hp1999-2010
VW NEW BEETLE Décapotable (1Y7) 1.8 TAWU, AWV, BKF150 hp2003-2010
VW PASSAT B5 (3B2) 1.8 TANB, APU, ATW, AUG, AEB150 hp1996-2000
VW PASSAT B5 Variant (3B5) 1.8 TANB, APU, ATW, AUG, AEB150 hp1997-2000
VW PASSAT B5.5 (3B3) 1.8 TAWM170 hp2001-2005
VW PASSAT B5.5 (3B3) 1.8 T 20VAWT150 hp2000-2005
VW PASSAT B5.5 (3B3) 1.8 T 4motionAWM170 hp2003-2005
VW PASSAT B5.5 Variant (3B6) 1.8 4motionAWM170 hp2003-2005
VW PASSAT B5.5 Variant (3B6) 1.8 TAWM170 hp2002-2005
VW PASSAT B5.5 Variant (3B6) 1.8 T 20VAWT150 hp2000-2005
VW POLO IV (9N_, 9A_) 1.8 GTIBJX150 hp2005-2009
VW POLO IV (9N_, 9A_) 1.8 GTi Cup EditionBBU180 hp2006-2009
VW SHARAN (7M8, 7M9, 7M6) 1.8 T 20VAWC, AJH150 hp1997-2010

OEM part number (inlet valve): 058 109 601 C

Important: the 2.7 T twin-turbo (APB, AZB, ARE, BES) needs 18 inlet valves and is not covered here.

Related products

When a 1.8 T 20V head goes back together, swap the exhaust valves and valve stem seals at the same time. Find the parts for these engines here:

1.8 T 20V exhaust valves →
6 mm inlet valve stem seals →

16 other products in the same category

Viewed products

Loading...