Skip to content
  • In stock
Toyota 7MGTE Soupape échappement inconel SUPERTECH 28x5.97x98.20mm Toyota 7MGTE Soupape échappement inconel SUPERTECH 28x5.97x98.20mm

Reinforced exhaust valves VAG 1.8T 20V A3 S3 A4 TT Golf 4 New Beetle Polo

€232.99 (tax incl.)
€291.24 (tax incl.) -20%

Set of 8 reinforced exhaust valves for the Audi / VW 1.8T 20V.

  • Brands: SUPERTECH, FERREA
  • Engines: 1.8T 20V (A3, S3, A4, TT, Golf IV, New Beetle, Polo GTI)
  • Dimensions: 29.9 mm or 30.9 mm head, 6 mm stem
  • Material: nitrided stainless steel, Inconel or sodium filled Nimonic, single groove or 3 grooves
AEVN-1103-8
3 in stock in France
4 in stock in Europe (72h lead time)
Available in stock in France
Pay in installments

Audi and Volkswagen engines covered

The 1.8T 20V is the Volkswagen group's turbocharged four-cylinder with five valves per cylinder. At Audi it powers the A3 and S3 8L, the A4 B5, B6 and B7 and the TT 8N, from 150 to 225 hp depending on the engine code (AEB, AGU, AJL, AJQ, AMK, APX, ARZ, AUM, BAM, BEX, BFB and others).

At Volkswagen, the 20-valve 1.8T turbocharged four-cylinder powers the Golf IV and its GTI version, the New Beetle and the Polo GTI 9N, with 150 or 180 hp depending on the engine code (AGU, AQA, ARZ, AUM, AUQ, AWP, AWV, BBU, BJX, BKF and others).

Each cylinder has two exhaust valves, 8 in total, operated by hydraulic tappets. The original valve 058 109 611 E has a 29.9 mm head, a 6 mm stem and a length of 103.9 mm. On an engine so often remapped or fitted with a larger turbo, it takes the rise in temperature of the gases heading for the turbine.

SUPERTECH and FERREA reinforced exhaust valves

Each time it opens, the exhaust valve of the 1.8T 20V sends combustion gases at very high temperature towards the turbine. Taken in the metal itself, the head runs at 760 to 870 °C on an engine without a turbo and goes beyond 1,000 °C on this turbocharged four-cylinder. It sheds that heat mainly through contact with its seat, which takes about 75 %, then through the guide, which takes close to 20 %. A valve steel of the EV8 family, used as a point of comparison, keeps 550 MPa at around 600 °C but only 300 MPa near 800 °C. With more boost, revs or load, the head runs hotter, fatigues, warps and starts to leak.

The reinforced versions use metals built for these temperatures. SUPERTECH offers three: a black nitride stainless steel, with a hardened and smoothed skin against wear and friction; Inconel, a nickel-rich superalloy that retains 860 MPa at 730 °C and still 554 MPa around 815 °C, nearly 85 % better than EV8 steel beyond 800 °C, the pick once the turbo blows hard; and finally a Nimonic, another nickel alloy, whose hollow sodium filled stem carries the heat picked up by the head towards the guide. At FERREA, the Competition Plus range, in stainless steel with a chromed stem, claims 20 % more hot strength and 25 % more seat life.

A +1 mm oversize is also available: stem and length stay the same, only the head grows from 29.9 to 30.9 mm. Spent gases exit faster towards the turbo, freeing room for fresh charge, and power rises. The 8 exhaust seats of the cylinder head must then be recut to this diameter.

Exhaust valve technical specifications

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
AEVN-1103-8 SUPERTECH Standard 29.9 mm 6 mm 103.9 mm 3 Black nitride stainless steel
AEVI-1103-8 SUPERTECH Standard 29.9 mm 6 mm 103.9 mm 3 Inconel
AEVI-1103S-8 SUPERTECH Standard 29.9 mm 6 mm 103.9 mm 1 Inconel
AEVI-1103S-HS-8 SUPERTECH Standard 29.9 mm 6 mm 103.9 mm 1 Sodium filled Nimonic
AEVI-1106S-8 SUPERTECH +1 mm 30.9 mm 6 mm 103.9 mm 1 Inconel
AEVI-1106S-HS-8 SUPERTECH +1 mm 30.9 mm 6 mm 103.9 mm 1 Sodium filled Nimonic
F1554P*8 FERREA Standard 29.9 mm 6 mm 103.9 mm 3 Stainless steel, chrome stem
F1555P*8 FERREA +1 mm 30.9 mm 6 mm 103.9 mm 3 Stainless steel, chrome stem

Valve fitting

PartAudi / Volkswagen originalReinforced
Collets KPR-VW6-T (3 grooves) / KPR-6S-7 (single groove)
Valve stem seals 036 109 675 A VS-VBM6E-8 (exhaust)
Valve guide GDE-AU18T

The number of grooves determines the collets: the four single groove part numbers are fitted with the KPR-6S/7.

At the standard 29.9 mm size the exhaust seats are kept; the 30.9 mm versions require them to be cut to that size.

The original valve stem seals carry part number 036 109 675 A.

Technical guide

Our brands

SUPERTECH SUPERTECH, which grew up in Silicon Valley, has been drawing up racing valves, springs, valve guides and titanium retainers for three decades. Whether stainless, titanium or Inconel, every valve starts from a specific engine and is validated alongside circuit, rally and drag racing teams.
FERREA FERREA Racing Components was set up in 1978 on the initiative of Horacio Ferrea and Daniel Urrutia. Its Florida and Argentina plants turn out stainless, nickel superalloy and titanium valves, chosen by engine builders across the globe, from drag racing to NASCAR.

How to choose

Located beneath the spring retainer, the collets slot into the grooves of the stem and keep the valve in place. One groove or three: the stem is not held in the same way, and what you gain from it changes too.

CriterionOption 1Option 2
Size Standard size
29.9 mm head, meant for a head on which nobody has ever touched the exhaust seats: direct fitting, no machining.
+1 mm oversize
30.9 mm head: burnt gases rush faster towards the turbo, the cylinder scavenges better and takes in more fresh charge, to the benefit of power (around 10 to 12 cfm for each millimetre gained). Seats machined to suit; rescues previously recut seats too.
Grooves 3 grooves
Factory arrangement, with the stem turning freely inside its collets. Fine for a mildly modified road 1.8T, with no other addition; new collets advised (original or KPR-VW6-T). Weakness: a closing impact loads the bottom groove, the thinner one. Only arrangement offered by FERREA on this engine.
Single groove
Gripped by the collets, the stem takes the load off its groove and the broader bearing area lowers friction: hard springs, big lift and high revs are handled better. SUPERTECH option for the most tuned 1.8T, available in Inconel and in sodium filled Nimonic, to favour with a bigger turbo. KPR-6S-7 collets required, preferably new.

When reinforced valves become necessary

  • Remap with more boost or an upgraded turbo (Inconel version advised)
  • Stiffer valve springs or higher lift camshafts
  • Raised rev limit
  • Cylinder head rebuilt for track, rally or hill climb use
  • Original exhaust valves marked, burnt or worn

Vehicle compatibility

ModelEngine codePowerYears
Audi A3 (8L) 1.8T AGU / AQA / ARX / ARZ / AUM 150 hp 1996-2003
Audi A3 (8L) 1.8T AJQ / APP / ARY / AUQ 180 hp 1998-2003
Audi S3 (8L) AMK / APY 210 hp 1999-2002
Audi S3 (8L) BAM 225 hp 2001-2003
Audi A4 (B5) 1.8T AEB / ANB / APU / ARK / ATW / AWT 150 hp 1995-2001
Audi A4 (B5) 1.8T AJL 180 hp 1997-2001
Audi A4 (B6) 1.8T AVJ 150 hp 2000-2002
Audi A4 (B6) 1.8T BFB 163 hp 2002-2005
Audi A4 (B6) 1.8T BEX 190 hp 2002-2004
Audi A4 (B7) 1.8T BFB 163 hp 2004-2009
Audi TT (8N) 1.8T AUM 150 hp 2001-2006
Audi TT (8N) 1.8T AJQ / APP / ARY / ATC / AUQ / AWP 180 hp 1998-2006
Audi TT (8N) 1.8T quattro APX / BAM / BEA 225 hp 1998-2006
Volkswagen Golf IV (1J) 1.8T AGU / AQA / ARZ / AUM / AWD 150 hp 1997-2005
Volkswagen Golf IV GTI (1J) 1.8T AUQ / BEK 180 hp 2001-2005
Volkswagen New Beetle (9C) 1.8T AGU / APH / AVC / AWU / AWV / BKF 150 hp 1999-2010
Volkswagen New Beetle (9C) 1.8T AWP / BNU 180 hp 2001-2005
Volkswagen Polo GTI (9N) 1.8T BJX 150 hp 2005-2009
Volkswagen Polo GTI Cup Edition (9N) 1.8T BBU 180 hp 2006-2009

OEM part number (exhaust valve): 058 109 611 E

Important: the sets of 8 match the 8 exhaust valves of the 1.8T 20V; the 2.7T V6 (APB) and the RS6 V8 (BCY) have a different number of valves and are not covered by this page. The same part numbers also fit the Volkswagen, SEAT and Skoda 1.8T 20V.

Don't forget the inlet valves

On a 1.8T 20V with the cylinder head removed, also replace the inlet valves and their valve stem seals so you refit a brand new assembly. The inlet valve page:

1.8T 20V inlet valves →

16 other products in the same category

Viewed products

Loading...