Skip to content
  • In stock
6 mm valve collets SUPERTECH and FERREA 6 mm valve collets SUPERTECH and FERREA

6 mm valve collets

€30.56 (tax incl.)
€38.20 (tax incl.) -20%

SUPERTECH and FERREA valve collets for 6 mm stems, in sets or in pairs.

  • Brands: SUPERTECH, FERREA
  • Valve stem: 6 mm
  • Types: 1 groove, 3 grooves or radial groove; 6°, 7°
  • Packs: SUPERTECH sets; FERREA pairs (1 pair per valve)
KPR-VW6-T-16
9 in stock in France
3 in stock in Europe (72h lead time)
Available in stock in France
Pay in installments

The 6 mm valve collets

Valve collets, also called keepers, hold the upper spring retainer on the valve stem. Their tapered outer face wedges into the retainer: this wedging, tightened by the spring pressure, is what holds the valve. The inner bead, which sits in the stem groove, mainly serves to position them. Two are needed per valve.

This page brings together the SUPERTECH and FERREA collets for 6 mm valve stems, sold in sets (SUPERTECH) or in pairs (FERREA): each choice in the menu shows the type and the quantity.

Compared with original collets, usually with 3 grooves, SUPERTECH single-groove collets clamp the valve stem and limit its rotation: the valve stays held with uprated springs, high lift and high revs, and its stem lasts longer. FERREA collets, made of heat-treated, black-oxide 4140 chrome-moly steel, sit in a radial groove with rounded corners which, according to the manufacturer, extends the life of the groove area by about 30%. SUPERTECH 3-groove collets keep the original design, for a rebuild without changing the valves.

For each FERREA part number, the menu shows the intended engine, or no engine for generic part numbers. They are fitted with a FERREA retainer of the same angle.

Technical specifications

BrandPart numberTypeGroovesAnglePack
SUPERTECH KPR-MIATA97+ 1 groove, 6°, Mazda MX-5 from 1997 1 6° sets of 16
SUPERTECH KPR-6N-6-ST 1 groove, 6°, Nissan profile 1 6° sets of 16, 24
SUPERTECH KPR-6T-ST 1 groove, 6°, Toyota / Subaru profile 1 6° sets of 16, 24, 32
SUPERTECH KPR-6S-7 1 groove, 7° 1 7° sets of 12, 16, 20, 24, 32, 36, 40, 48, 64, 80
SUPERTECH KPR-VW6-T 3 grooves, 7°, Audi / BMW / Opel profile 3 7° sets of 12, 16, 24, 40, 48, 64, 80
FERREA K10079 Radial groove, 6°, Dodge Neon SRT-4 2.4 1 radial 6° pair (for 1 valve)
FERREA K10063 Radial groove, 6°, Nissan RB25DET and RB25 Neo 1 radial 6° pair (for 1 valve)
FERREA K10072 Radial groove, 6°, Nissan RB26DETT 1 radial 6° pair (for 1 valve)
FERREA K10036 Radial groove, 6°, Nissan SR20 1 radial 6° pair (for 1 valve)
FERREA K10081 Radial groove, 6°, Nissan TB48DE 1 radial 6° pair (for 1 valve)
FERREA K10069 Radial groove, 6°, Nissan VQ35 1 radial 6° pair (for 1 valve)
FERREA K10092 Radial groove, 6°, Porsche M96 1 radial 6° pair (for 1 valve)
FERREA K10061 Radial groove, 6°, Subaru EJ20 1 radial 6° pair (for 1 valve)
FERREA K10074 Radial groove, 6°, Subaru EJ207 STI 1 radial 6° pair (for 1 valve)
FERREA K10037 Radial groove, 6°, Toyota 2JZ / 7M / 3S-GTE 1 radial 6° pair (for 1 valve)
FERREA K10108 Radial groove, 6°, Toyota 3S-GTE 3rd generation 1 radial 6° pair (for 1 valve)
FERREA K10111 Radial groove, 6°, Top Lock 1 radial 6° pair (for 1 valve)
FERREA K10123 Radial groove, 7°, BMW S58 exhaust 1 radial 7° pair (for 1 valve)

Technical guide

Choosing the groove type

The groove is where the collets lock the valve under the spring retainer. Its design determines how the valve is held: the collets must always have the same number of grooves and the same profile as the valve.

Criterion3 grooves1 grooveRadial groove
Principle Original design on many engines. The collets do not clamp the stem: the valve rotates with the retainer. The collets clamp the stem above and below the groove: the valve is held and hardly rotates. A single groove with a rounded profile, without sharp edges, which spreads the stress better.
Advantage Keeps the original design: rebuild without changing the valves. The groove carries little load: according to SUPERTECH, the stem lasts longer than with the original triple groove. According to FERREA, about 30% longer life for the groove area. It is the reference design in top-level racing and on titanium valves.
Use Road engine with springs and rev limit close to standard. Tuned engine with uprated springs, high lift and high revs: circuit, drift, rally or drag racing. High revs and risk of valve float, in advanced builds.
On this page KPR-VW6-T KPR-MIATA97+, KPR-6N-6-ST, KPR-6T-ST, KPR-6S-7 All FERREA part numbers

The right angle

The taper of the collets must have exactly the same angle as the upper retainer. Mixing two angles hammers the valve groove and can break the retainer or the valve. 7° is the standard angle; several SUPERTECH and FERREA part numbers on this page are 6°, depending on the engine; the FERREA “Super 7” actually measures 8° and only fits a Super 7 retainer.

Identifying the angle: the FERREA T7000 gauge

FERREA T7000 retainer angle gauge

The FERREA T7000 gauge measures the angle of a steel or titanium spring retainer, for example when its marking has worn off. It has four cones: 6°, 7°, Super 7 (8°) and 10°. Fit the retainer on the cone of the expected angle. If it sits without play, that is the right angle. If not, try the next cone.

FERREA T7000 gauge →

Choosing your collets

With uprated springs, choose collets from the same brand as the retainers, with the same angle, and with the same groove design as the valves.

For SUPERTECH part numbers, the brand shown in the menu is the one whose original profile SUPERTECH reproduces; always check the diameter, groove and angle of your valves and retainers.

  1. The valve stem diameter: 6 mm on this page.
  2. The groove design of the valve: 1 groove, 3 grooves or radial groove, to be matched exactly.
  3. The angle of the upper retainer.
  4. The quantity: two collets per valve, i.e. 32 for a 16-valve engine; with FERREA, one pair per valve.

Collets are replaced at every cylinder head rebuild: a worn collet has taken the shape of its old valve and seats poorly on a new valve. When fitted, a slight gap must remain between the two halves.

Our brands

SUPERTECH SUPERTECH, based in San Jose, California, has been making racing valvetrain parts for more than 30 years: valves, springs, retainers, collets and tappets. Its single-groove collets clamp the valve stem and limit its rotation, so the stem lasts longer than with the original triple groove.
FERREA FERREA Racing Components, founded in 1978 in Florida by two Argentinian engine builders, Horacio Ferrea and Daniel Urrutia, makes its entire valvetrain in-house, from valves to springs, tappets and rocker arms. Its radial-groove collets, made of heat-treated alloy steel, are designed for its own valves and retainers.
Important: two collets per valve. Check the retainer angle and the number of grooves on your valves before ordering.

Don't forget the lash caps

On engines where the valve clearance is set by a lash cap fitted on the valve stem, under the tappet, we offer lash caps of the same diameter:

6 mm lash caps →

16 other products in the same category

Viewed products

Loading...