Skip to content
  • On order
Toyota 7MGTE Soupape échappement inconel SUPERTECH 28x5.97x98.20mm Toyota 7MGTE Soupape échappement inconel SUPERTECH 28x5.97x98.20mm

7 mm valve collets

€29.70 (tax incl.)
€37.13 (tax incl.) -20%

SUPERTECH and FERREA valve collets for 7 mm stems, in sets or in pairs.

  • Brands: SUPERTECH, FERREA
  • Valve stem: 7 mm
  • Types: 1 groove, 3 grooves or radial groove; 6°, 7° or Super 7
  • Packs: SUPERTECH sets; FERREA pairs (1 pair per valve)
KPR-VW7-S-16
On order, 15 to 30 days lead time
Pay in installments

The 7 mm valve collets

Valve collets, also called keepers, hold the upper spring retainer on the valve stem. Their tapered outer face wedges into the retainer: this wedging, tightened by the spring pressure, is what holds the valve. The inner bead, which sits in the stem groove, mainly serves to position them. Two are needed per valve.

This page brings together the SUPERTECH and FERREA collets for 7 mm valve stems, sold in sets (SUPERTECH) or in pairs (FERREA): each choice in the menu shows the type and the quantity.

Compared with original collets, usually with 3 grooves, SUPERTECH single-groove collets clamp the valve stem and limit its rotation: the valve stays held with uprated springs, high lift and high revs, and its stem lasts longer. FERREA collets, made of heat-treated, black-oxide 4140 chrome-moly steel (titanium for K11000 and K11001), sit in a radial groove with rounded corners which, according to the manufacturer, extends the life of the groove area by about 30%. SUPERTECH 3-groove collets keep the original design, for a rebuild without changing the valves. FERREA advises against fitting its K11000 and K11001 titanium collets on a stainless steel valve.

For each FERREA part number, the menu shows the intended engine, or no engine for generic part numbers. They are fitted with a FERREA retainer of the same angle.

Technical specifications

BrandPart numberTypeGroovesAnglePack
SUPERTECH KPR-VW7-S 1 groove, 6°, VW 16V 1 6° sets of 8, 16, 24, 32, 40, 48
SUPERTECH KPR-VW7-T 3 grooves, 7°, BMW / VW profile 3 7° sets of 8, 12, 16, 24, 32, 40, 48
FERREA K10082 Radial groove, 7°, Audi 20V and V8, VW 16V 1 radial 7° pair (for 1 valve)
FERREA K10062 Radial groove, 7°, Nissan KA24DE 1 radial 7° pair (for 1 valve)
FERREA K10096 Radial groove, 7°, Toyota 1FZ-FE 1 radial 7° pair (for 1 valve)
FERREA K10099 Radial groove, 7°, VW VR6 1 radial 7° pair (for 1 valve)
FERREA K10085 Radial groove, 7° 1 radial 7° pair (for 1 valve)
FERREA K10086 Radial groove, 7°, shouldered 1 radial 7° pair (for 1 valve)
FERREA K10046 Radial groove, Super 7 (8°) 1 radial Super 7 (8°) pair (for 1 valve)
FERREA K10047 Radial groove, Super 7 (8°), +1.27 mm, lash cap recess 1 radial Super 7 (8°) pair (for 1 valve)
FERREA K10049 Radial groove, Super 7 (8°), with lash cap FERREA C10005 1 radial Super 7 (8°) pair (for 1 valve)
FERREA K11000 Titanium, radial groove, Super 7 (8°) 1 radial Super 7 (8°) pair (for 1 valve)
FERREA K11001 Titanium, radial groove, Super 7 (8°), +1.27 mm 1 radial Super 7 (8°) pair (for 1 valve)

Technical guide

Choosing the groove type

The groove is where the collets lock the valve under the spring retainer. Its design determines how the valve is held: the collets must always have the same number of grooves and the same profile as the valve.

Criterion3 grooves1 grooveRadial groove
Principle Original design on many engines. The collets do not clamp the stem: the valve rotates with the retainer. The collets clamp the stem above and below the groove: the valve is held and hardly rotates. A single groove with a rounded profile, without sharp edges, which spreads the stress better.
Advantage Keeps the original design: rebuild without changing the valves. The groove carries little load: according to SUPERTECH, the stem lasts longer than with the original triple groove. According to FERREA, about 30% longer life for the groove area. It is the reference design in top-level racing and on titanium valves.
Use Road engine with springs and rev limit close to standard. Tuned engine with uprated springs, high lift and high revs: circuit, drift, rally or drag racing. High revs and risk of valve float, in advanced builds.
On this page KPR-VW7-T KPR-VW7-S All FERREA part numbers

The right angle

The taper of the collets must have exactly the same angle as the upper retainer. Mixing two angles hammers the valve groove and can break the retainer or the valve. 7° is the standard angle; several SUPERTECH and FERREA part numbers on this page are 6°, depending on the engine; the FERREA “Super 7” actually measures 8° and only fits a Super 7 retainer.

Identifying the angle: the FERREA T7000 gauge

FERREA T7000 retainer angle gauge

The FERREA T7000 gauge measures the angle of a steel or titanium spring retainer, for example when its marking has worn off. It has four cones: 6°, 7°, Super 7 (8°) and 10°. Fit the retainer on the cone of the expected angle. If it sits without play, that is the right angle. If not, try the next cone.

FERREA T7000 gauge →

Offset collets

The “+1.27 mm” part numbers move the retainer by 1.27 mm on the stem: they are used to set the installed spring height without machining the seat. After fitting, recheck the spring seat pressure and the margin before coil bind.

Choosing your collets

With uprated springs, choose collets from the same brand as the retainers, with the same angle, and with the same groove design as the valves.

For SUPERTECH part numbers, the brand shown in the menu is the one whose original profile SUPERTECH reproduces; always check the diameter, groove and angle of your valves and retainers.

  1. The valve stem diameter: 7 mm on this page.
  2. The groove design of the valve: 1 groove, 3 grooves or radial groove, to be matched exactly.
  3. The angle of the upper retainer.
  4. The quantity: two collets per valve, i.e. 32 for a 16-valve engine; with FERREA, one pair per valve.

Collets are replaced at every cylinder head rebuild: a worn collet has taken the shape of its old valve and seats poorly on a new valve. When fitted, a slight gap must remain between the two halves.

Our brands

SUPERTECH SUPERTECH, based in San Jose, California, has been making racing valvetrain parts for more than 30 years: valves, springs, retainers, collets and tappets. Its single-groove collets clamp the valve stem and limit its rotation, so the stem lasts longer than with the original triple groove.
FERREA FERREA Racing Components, founded in 1978 in Florida by two Argentinian engine builders, Horacio Ferrea and Daniel Urrutia, makes its entire valvetrain in-house, from valves to springs, tappets and rocker arms. Its radial-groove collets, made of heat-treated alloy steel, are designed for its own valves and retainers.
Important: two collets per valve. Check the retainer angle and the number of grooves on your valves before ordering.

Don't forget the lash caps

On engines where the valve clearance is set by a lash cap fitted on the valve stem, under the tappet, we offer lash caps of the same diameter:

7 mm lash caps →

15 other products in the same category

Viewed products

Loading...