Skip to content
  • On order
Reinforced inlet valves SUPERTECH BMW S50B30 Reinforced inlet valves SUPERTECH BMW S50B30

Reinforced inlet valves SUPERTECH BMW S50B30

€403.12 (tax incl.)
€503.90 (tax incl.) -20%

Set of 12 reinforced inlet valves for the European BMW S50B30.

  • Brand: SUPERTECH
  • Engine: S50B30 (Europe)
  • Dimensions: 34 mm head, 7 mm stem
  • Material: stainless steel, 3 grooves
BMIVN-1036-12
On order, 15 to 30 days lead time
Pay in installments

BMW engines covered

The S50B30, in its 3.0 litre, 24-valve European version, is the inline six-cylinder petrol engine of the BMW M3 3.0 E36 saloon, coupe and convertible, and of the M3-R 3.0.

It takes 12 inlet valves, BMW part number 11 34 1 401 104: 34.0 mm head, 7.0 mm stem, held by 3-groove collets, with mechanical tappets and shims. Designed for the standard engine, they reach their limits with sharper camshafts, firmer springs, higher revs or forced induction.

SUPERTECH reinforced inlet valves

As the S50 climbs through the rev range, each inlet valve admits and then cuts off air to the cylinder tens of times within a single second. Its head comes down hard on its seat whenever it shuts, and the stem never stops sliding in the guide. The working range is 400 to 550 °C, yet the chrome-silicon steel supplied with the engine already loses ground there: 500 MPa at 500 °C, then 250 MPa near 600 °C, only one step higher, which means 50 % less strength. More lift, stiffer springs, a higher rev ceiling or extra boost each pile on shocks, rubbing and heat until the valve is worn out.

For these uprated parts SUPERTECH uses a forged chrome-nickel stainless steel kept for motorsport, a close relative of EV8 (21-4N). This metal keeps 650 MPa at 500 °C, 30 % better than the factory steel, and 550 MPa at 600 °C, 120 % better. The black nitride treatment gives the part a harder, smoother skin: less friction in the guide, less wear on the stem. These valves keep the standard dimensions of the European S50B30, namely a 34.0 mm head and a 7 mm stem, so no seat machining is needed.

Inlet valve technical specifications

Part numberBrandSizeHead Ø
OEM 34.0 mm
Stem Ø
OEM 7 mm
LengthGroovesMaterial
BMIVN-1036-12 SUPERTECH Standard 34.0 mm 7 mm 119.75 mm 3 Black nitrided stainless

Valve fitting

PartBMW originalReinforced
Valve collets 11 34 1 307 136 (3 grooves) KPR-VW7-T (3 grooves)
Valve stem seals Kit 11 34 9 059 172 VS-VW7I-12 (inlet)
Valve guide 11 12 1 315 999

SUPERTECH pairs its 3-groove valves with its KPR-VW7-T collets; new collets are recommended on reassembly.

The S50B30 has mechanical tappets with shims: after replacing the valves, check the clearance and adjust the shims.

Technical guide

The brand offered

SUPERTECH SUPERTECH has made a full racing valvetrain range for more than 30 years at its Californian site in San Jose. Each valve there is thought out around one engine, put through ultrasound, radiography and laser readings, then proven alongside tuners, in drag racing or on track.

When reinforced valves become necessary

  • Sharper camshafts or stiffer springs fitted
  • Rev limiter set above stock
  • Switch to turbo or supercharger
  • Head prepared for track, drift or rally
  • Factory valves tired, pitted or reworked to repair size

Vehicle compatibility

ModelEngine codePowerYears
M3 3.0 (E36) S50B30 286 hp 1994-1995
M3 3.0 Coupe (E36) S50B30 286 hp 1992-1995
M3 3.0 Convertible (E36) S50B30 286 hp 1994-1995
M3 3.0 Coupe (E36) S50B30 295 hp 1993-1995
M3-R 3.0 Coupe (E36) S50B30 329 hp 1994-1995

OEM part number (inlet valve): 11 34 1 401 104

Important: these valves fit neither the American S50B30 (33.0 mm head, 6 mm stem) nor the S50B32 of the M3 3.2 (6 mm stem).

Don't forget the exhaust valves

Overhauling an S50 cylinder head normally goes with new exhaust valves, and with valve stem seals replaced too. Here is what we offer for this engine:

BMW S50B30 exhaust valves →

15 other products in the same category

Loading...