Skip to content
  • On order
Reinforced exhaust valves BMW M3 E36 S50B30 Reinforced exhaust valves BMW M3 E36 S50B30

Reinforced exhaust valves BMW M3 E36 S50B30

€570.92 (tax incl.)
€713.65 (tax incl.) -20%

Set of 12 reinforced exhaust valves for the European BMW S50B30.

  • Brand: SUPERTECH
  • Engine: S50B30 Europe (M3 E36 3.0)
  • Dimensions: 30.6 mm head, 7 mm stem
  • Grooves: 3 grooves
BMEVI-1036-12
On order, 15 to 30 days lead time
Pay in installments

BMW engines covered

The European 3.0 litre version of the S50 straight six, the S50B30 displaces 2,990 cc (86 mm bore, 85.8 mm stroke); it was built from 1992 to 1995 and produces 286 hp in the M3 E36 3.0.

Its 24-valve cylinder head with solid tappets and shims takes 12 BMW exhaust valves with a 30.5 mm head and a 7 mm stem, with 3-groove collets. The later S50B32 and the US S50B30 moved to 6 mm stems: this engine therefore needs valves of its own.

SUPERTECH reinforced exhaust valves

Sitting in the stream of gases leaving the cylinder, the head of this valve reaches 760 to 870 °C in a naturally aspirated unit and passes 1,000 °C under boost. Close to 75 % of the heat goes into the seat, about 20 % into the guide. An EV8 type exhaust steel offers only 300 MPa at 800 °C, against 550 MPa at 600 °C. Each rise in load, revs or boost makes the head run hotter; it suffers fatigue, may distort and ends up seating poorly.

To cope with these temperatures, SUPERTECH produces the BMEVI-1036 in Inconel, a nickel superalloy: 860 MPa at 730 °C and 554 MPa still at around 815 °C, roughly 85 % extra strength compared with an EV8 steel near 800 °C. For a tuned engine, or one running a turbo or supercharger, it is the obvious material.

A single version is sold, at the original size: the 30.6 mm head carries the standard size of the European S50B30, so the seats need no rework. Flat head, stem narrowed under the head and 3 grooves: the BMW part's architecture is retained.

Exhaust valve technical specifications

Part numberBrandSizeHead Ø
OEM 30.5 mm
Stem Ø
OEM 7 mm
LengthGroovesMaterial
BMEVI-1036-12 SUPERTECH Standard 30.6 mm 7 mm 121.2 mm 3 Inconel

Valve fitting

PartBMW originalReinforced
Collets 11 34 1 307 136 (3 grooves) KPR-VW7-T-24 (3 grooves)
Valve stem seals kit 11 34 9 059 172 VS-VW7E-12 (exhaust)
Valve guide 11 12 1 315 999

Like the BMW valve, the BMEVI-1036 has 3 grooves: it takes the 3-groove KPR-VW7-T collets intended for the 7 mm stem, preferably new.

Its 30.6 mm head stays at the maker's standard size: the exhaust seats are checked during the rebuild, with no change of size.

For sealing, the 7 mm VS-VW7E-12 exhaust valve stem seals complete the fitting.

Technical guide

Our brand

SUPERTECH SUPERTECH Performance, rooted in Silicon Valley, has developed guides, valves, springs and titanium retainers for competition for more than 30 years. Stainless, titanium or Inconel, each valve is engineered engine after engine and validated with respected tuners, from drag racing to rally and circuit work.

How to choose

Placed under the spring retainer, the collets locate in the stem grooves to keep the valve in position. Their count governs how it is held; here a single version with 3 grooves is offered, with the following points:

CriterionAvailable version
Size Standard, 30.6 mm
Standard size of the European S50B30, in Inconel: it suits original exhaust seats that have never been recut, with no machining at all.
Grooves 3 grooves
Same layout as the BMW valve: the stem stays free in its collets. A closing impact mainly loads the bottom groove, which is the thinnest; KPR-VW7-T collets, preferably new.

When reinforced valves become necessary

  • More aggressive camshaft profiles or uprated valve springs
  • Rev limit pushed higher
  • Switch to a turbo or supercharger (Inconel is then the right choice)
  • Head refreshed for track, drift or rally
  • Original valves damaged, worn or brought back to repair size

Vehicle compatibility

ModelEngine codePowerYears
M3 (E36) 3.0 S50B30 286 hp 1992-1995
M3-R (E36) 3.0 S50B30 329 hp 1992-1995

OEM part number (exhaust valve): 11 34 1 401 105

Important: the US S50B30, derived from the M50, uses valves with a 6 mm stem and is not covered by this page, nor is the S50B32 (M3 E36 3.2, Z3 M), which has its own product page.

Don't forget the inlet valves

An opened cylinder head is the moment to renew the valve stem seals and inlet valves while the exhaust side is done. Here are the parts designed for this same engine:

BMW M3 E36 S50B30 inlet valves →
7 mm exhaust valve stem seals →

15 other products in the same category

Viewed products

Loading...