- On order
Reinforced inlet valves BMW M5 E60 E61 M6 E63 E64 S85B50
Set of 20 reinforced inlet valves for BMW M5 and M6 S85B50.
- Brand: SUPERTECH
- Engines: S85B50 (V10 5.0 40V)
- Dimensions: 35.4 mm head, 4.97 mm stem, 111.75 mm long
- Material: black nitrided stainless steel, 1 groove
BMW engines covered
The S85B50 is the naturally aspirated BMW M V10: 5.0 litres, 40 valves, twin overhead camshafts per bank and hydraulic tappets. It powers the M5 E60 and E61 and the M6 E63 and E64 (507 hp).
Its 20 original inlet valves have a 35.7 mm head and a 4.97 mm stem: BMW 11 34 7 833 775 on engines built up to August 2008, then 11 34 7 838 293, shared with the S65 V8. Higher revs, sharper camshafts or track use expose them to more heat and impact.
SUPERTECH reinforced inlet valves
In the S85B50 V10 of the M5 and M6, each of the 20 inlet valves lifts under the cam to fill its cylinder with fresh air, then snaps back onto its seat, while its 4.97 mm stem shuttles through the guide. Working heat ranges between 400 and 550 °C: at such levels, ordinary chrome-silicon steel keeps only 250 MPa at 600 °C against 500 MPa at 500 °C, a 50 % fall in strength.
The SUPERTECH BMIVN-1065-20 pairs a stainless body with black nitriding: hardened at the surface, its stem copes better with rubbing in the guide, wears at a slower rate and resists scuffing. Its stem stays at the original 4.97 mm and its head measures 35.4 mm.
Inlet valve technical specification
| Part number | Brand | Size | Head Ø OEM 35.7 mm | Stem Ø OEM 4.97 mm | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| BMIVN-1065-20 | SUPERTECH | Standard | 35.4 mm | 4.97 mm | 111.75 mm | 1 | Stainless steel, black nitrided |
Fitting details
| Part | BMW original | Reinforced |
|---|---|---|
| Collets | 11 34 1 340 846 / 11 34 7 838 296 | |
| Valve stem seals | 11 34 0 032 548 | |
| Valve guide |
The SUPERTECH valve keeps the single groove of the original valve.
Supplied in standard size, it fits seats reconditioned during the cylinder head rebuild, with no machining to a new size.
Clearance is taken up by the hydraulic tappets: no adjustment is needed after the valves are replaced.
Technical guide
The brand offered
| From its Californian base, SUPERTECH Performance puts over three decades of experience into competition valves, springs and guides, and each batch gets an ultrasonic pass, a radiograph and then a laser reading before it reaches the engine builders who fit it. |
When reinforced valves become necessary
- Higher-lift camshafts or stiffened springs
- Fuel cut-off moved towards higher revs
- Forced induction added to the atmospheric V10
- Block prepared for circuit outings or racing
- Factory valves marked, tired or out of true
Compatible vehicles
| Model | Engine code | Power | Years |
|---|---|---|---|
| M5 (E60) | S85B50 | 507 hp | 2004-2009 |
| M5 Touring (E61) | S85B50 | 507 hp | 2007-2010 |
| M6 (E63) | S85B50 | 507 hp | 2005-2010 |
| M6 (E64) | S85B50 | 507 hp | 2006-2010 |
OEM part number (inlet valve): 11 34 7 833 775 / 11 34 7 838 293
Related products
As long as the V10's heads stay off, replace this engine's exhaust valves at the same go; they too are available in a reinforced build:
| Exhaust valves BMW M5 E60 E61 M6 E63 E64 S85B50 → |
-
Brand
-
ReferenceBMIVN-1065-20