- In stock
Reinforced inlet valves TOYOTA Supra 2JZ-GE 2JZ-GTE
Set of 12 reinforced inlet valves for TOYOTA 2JZ-GE and 2JZ-GTE (Supra A80, Aristo, Crown, Chaser, Mark II, Soarer).
- Brands: SUPERTECH, FERREA
- Engines: 2JZ-GE, 2JZ-GTE
- Dimensions: 33.5 mm, 33.6 mm or 34.5 mm head, 5.98 mm stem
- Material: black nitride stainless steel or stainless steel with chrome stem
TOYOTA engines covered
The 2JZ is Toyota's 3 litre 24-valve inline six: naturally aspirated 2JZ-GE from 214 to 231 hp, twin-turbo 2JZ-GTE from 279 to 330 hp. It powers the Supra A80 from 1993 to 2002, as well as the Aristo, Crown, Chaser, Cresta, Mark II, Soarer, Altezza, Progres and Origin.
The engine takes 12 Toyota 13711-46021 or 13711-46022 inlet valves (13711-46030 on the 1993 to 2005 2JZ-GE), with a 5.97 mm stem, held by 90913-03025 collets. Higher boost, sharper camshafts or a raised rev limit load them well beyond stock use.
SUPERTECH and FERREA reinforced inlet valves
In the 2JZ head, each cam presses on its tappet and pushes the inlet valve down: fresh air, or, on the 2JZ-GTE, the charge squeezed by its turbo, reaches the cylinder, then the valve climbs back, slapping its seat and riding up and down its guide. With the engine pulled towards the red line, this cycle repeats well over twenty times every second, giving the metal no rest. The part lives between 400 and 550 °C, yet stock chrome-silicon steel keeps only 500 MPa at 500 °C there and falls to 250 MPa at 600 °C, which cuts its strength by 50 %.
The SUPERTECH and FERREA valves sold here are cut from a racing stainless steel close to EV8, which retains 650 MPa at 500 °C and 550 MPa at 600 °C where stock steel weakens: 30 % and then 120 % more strength. SUPERTECH adds black nitriding to the stem, hardened and better polished, so it glides with less friction in the guide and wears more slowly as boost rises. FERREA uses its Competition Plus series with a hard chrome stem, rated by the maker at 20 % more heat and fatigue resistance, with seats lasting 25 % longer.
The TIVN-1016-12 carries a 34.5 mm head instead of the 33.5 mm of the standard-size TIVN-1014-12; stem (5.98 mm) and length (98.55 mm) stay the same. That extra millimetre widens the opening at the seat, so the cylinders take in a larger charge and the 2JZ gains power, once the head's seats are machined to 34.5 mm.
Inlet valve technical specification
| Part number | Brand | Size | Head Ø | Stem Ø | Length | Grooves | Material |
|---|---|---|---|---|---|---|---|
| TIVN-1014-12 | SUPERTECH | Standard | 33.5 mm | 5.98 mm | 98.55 mm | 1 | Black nitride stainless steel |
| TIVN-1016-12 | SUPERTECH | +1 mm | 34.5 mm | 5.98 mm | 98.55 mm | 1 | Black nitride stainless steel |
| F1498P*12 | FERREA | Standard | 33.6 mm | 5.98 mm | 98.55 mm | Stainless steel, chrome stem |
Fitting details
| Part | TOYOTA original | Reinforced |
|---|---|---|
| Collets | 90913-03025 | KPR-6T-ST-32 |
| Valve stem seals | 90913-02088 / 90913-02090 | VS-TS6I-12 / VS1009*12 |
| Valve guide | Inner Ø 6.010-6.030 mm | GDE-T2JZ-I-12 / VG1035*12 |
The +1 mm size requires the inlet seats to be cut to 34.5 mm, workshop work to plan with the cylinder head rebuild.
The 2JZ sets its valve clearance with shims on solid tappets: after replacing the valves, check the clearance and adjust the shims.
Technical guide
Our brands
| SUPERTECH earned its reputation in San Jose, California, where the company has shaped the complete valve train of competition engines for more than 30 years. Every part is born for a given head, goes under ultrasound, radiography and laser, then proves itself with engine tuners. | |
| FERREA Racing Components owes its birth, in 1978 in Fort Lauderdale (Florida), to two engine builders from Argentina. Nothing is subcontracted: every one-piece valve is drawn from a forged blank, finished on CNC machines, then raced in NASCAR, at drag strips and on circuits. |
How to choose
The choice of head rests on the state of the seat faces and the extra air wanted: 33.5 or 33.6 mm keeps the factory diameter, 34.5 mm pushes filling.
| Criterion | Option 1 | Option 2 |
|---|---|---|
| Size | Standard size 33.5 mm (SUPERTECH) or 33.6 mm (FERREA) head, the simplest route when the inlet side of the head still has its factory seat faces. |
+1 mm oversize 34.5 mm head: about 10 to 12 cfm of extra air for each millimetre of diameter. Seat faces to be machined in the workshop; equally suitable if the seats underwent an earlier regrind. |
When reinforced valves become necessary
- Wilder camshaft profile or uprated springs
- Turbo added to a 2JZ-GE or more boost on the GTE
- Fuel cut-off set higher in the rev range
- Engine destined for circuits, drift or rally stages
- Stock valves pitted, fatigued or reworked
Compatible vehicles
| Model | Engine code | Power | Years |
|---|---|---|---|
| Supra (A8) 3.0 | 2JZ-GE / 2JZ-GTE | 224-330 hp | 1993-2002 |
| Altezza (E1) 3.0 | 2JZ-GE | 214 hp | 2001-2005 |
| Altezza Gita (E1) 3.0 | 2JZ-GE | 214-220 hp | 2001-2005 |
| Aristo (S14) 3.0 | 2JZ-GE / 2JZ-GTE | 230-279 hp | 1990-1997 |
| Aristo (S16) 3.0 | 2JZ-GE / 2JZ-GTE | 231-280 hp | 1997-2004 |
| Chaser (X10) 3.0 | 2JZ-GE | 220 hp | 1996-2001 |
| Chaser (X9) 3.0 | 2JZ-GE | 220 hp | 1992-1996 |
| Cresta IV (X9) 3.0 | 2JZ-GE | 220 hp | 1992-1996 |
| Cresta V (X10) 3.0 | 2JZ-GE | 220 hp | 1996-2001 |
| Cresta V Break (X10) 3.0 | 2JZ-GE | 220 hp | 1996-2001 |
| Crown (S13, S14) 3.0 | 2JZ-GE | 220-230 hp | 1991-1995 |
| Crown (S15) 3.0 | 2JZ-GE | 220 hp | 1995-2001 |
| Crown (S17) 3.0 | 2JZ-GE | 220 hp | 1999- |
| Mark II Break (X1, V2) 3.0 | 2JZ-GE | 226 hp | 1996-2001 |
| Mark II VI 3.0 | 2JZ-GE | 230 hp | 1992-1996 |
| Mark II VIII (X10) 3.0 | 2JZ-GE | 220 hp | 1996-2001 |
| Origin (JCG1) 3.0 | 2JZ-GE | 214 hp | 2000-2001 |
| Progres (JCG1) 3.0 | 2JZ-GE | 215 hp | 1998-2004 |
| Soarer (Z3) 3.0 | 2JZ-GE | 226-230 hp | 1990-2000 |
OEM part number (inlet valve): 13711-46021 / 13711-46022; 13711-46030 (2JZ-GE, 1993-2005)
Related products
With the 2JZ head off, renew its 12 exhaust valves during that same rebuild; our shop also stocks them as reinforced parts, on the page linked below:
| TOYOTA Supra 2JZ-GE 2JZ-GTE exhaust valves → |
-
Brand
-
ReferenceTIVN-1014-12