Skip to content
  • On order
FERREA inlet valve stem seals Ford Zetec 2.0 FERREA inlet valve stem seals Ford Zetec 2.0

FERREA inlet valve stem seals Ford Zetec 2.0 5.5 mm stem

€19.35 (tax incl.)
€24.19 (tax incl.) -20%

Set of 8 inlet valve stem seals for the Ford Zetec 2.0 converted to 5.5 mm stems.

  • Brand: FERREA
  • Engines: Zetec 2.0 (Focus I, Escort, Focus USA)
  • Material: Viton (FKM)
VS1001*8
0 in stock in France
For larger quantities, 5 to 15 days lead time
Pay in installments

Ford engines concerned

This set is for the Ford Zetec 2.0 16-valve four-cylinder once it has been fitted with 5.5 mm stem valves and guides. The engine powers the Ford Focus I 2.0 16V, the Australian LR Focus and the 2.0 Escort and Focus sold in the United States.

Its head takes 8 inlet valves, two per cylinder, each topped by a seal that regulates the oil reaching the stem. With 5.5 mm stem valves, that seal must also be made for this diameter.

FERREA inlet valve stem seals

The seal caps the end of the guide and should pass only a trace of oil, just what the stem needs to slide without seizing. Too old or baked by heat, it becomes porous: the oil level drops faster, blue smoke shows at start-up or after a spell of idling, and deposits blacken valves and plugs.

For this build, FERREA makes the seal in Viton (FKM), a heat-tolerant rubber, and gives it a spring that holds the lip against the 5.5 mm stem to meter oil better when the engine works hard. The set of 8 covers the whole inlet of the converted Zetec; the exhaust has a different FERREA seal, sold separately.

Stem seal technical specifications

Part numberBrandPositionMaterialStem ØGuide ØSeal outside ØLip spring
VS1001*8 FERREA Inlet Viton (FKM) 5.5 mm Yes

Stem seal installation

PartOriginalReinforced
Inlet stem seal Replaced by this set
Exhaust stem seal VS1000*8
Valve guides
Valves

Technical guide

The brand offered

FERREA FERREA is a valvetrain specialist that machines its own valves, springs and guides and moulds its seals at its Florida and Argentina sites. Its parts serve tuned and race engines; the spring in the Viton seals keeps them sealing under load.

Inlet or exhaust?

For the converted Zetec 2.0, FERREA offers VS1001 for the inlet and VS1000 for the exhaust, the latter in a high-temperature compound. Both are Viton (FKM), carry a lip spring and suit a 5.5 mm stem, yet they do not interchange from one side of the cylinder head to the other. This engine needs 8 seals on the inlet and 8 on the exhaust.

When valve stem seals must be replaced

  • Oil vanishing faster, blue smoke on start-up
  • Valves pulled or cylinder head reconditioned
  • New valve guides installed
  • Uprated valves or springs installed

Vehicle compatibility

Ford

ModelEngine codePowerYears
Focus I 2.0 16V (DAW, DBW, DFW, DNW) EDDB / EDDC / EDDD / EDDF 126-131 hp 1998-2005
Focus I 2.0 (DFW, DNW) EDDD / 20LS9X 112-115 hp 1999-2004
Focus (LR) 2.0, 2.0 i EDDB / EDDD 116-131 hp 2002-2005
Focus 2.0 (USA) C20HDEZ 132 hp 1999-2004
Escort 2.0, 2.0 SE (USA) 99520 / D93 111-132 hp 1996-2003
Important: FERREA intends these seals for the Zetec 2.0 converted to 5.5 mm stem valves; they fit only with 5.5 mm stem valves and guides, not on the original valves.

Remember the exhaust valve stem seals

On a Zetec converted to 5.5 mm, the 8 inlet seals are renewed together with the 8 exhaust seals. FERREA supplies set VS1000:

FERREA exhaust stem seals Ford Zetec 2.0 →

9 other products in the same category

Viewed products

Loading...