Skip to content
  • In stock
Reinforced ARP cylinder head studs FORD EDDB EDDC EDDD EDDF Reinforced ARP cylinder head studs FORD EDDB EDDC EDDD EDDF

Reinforced ARP cylinder head studs FORD EDD

€201.57 (tax incl.)
€237.14 (tax incl.) -15%

ARP 8740 cylinder head stud kit (251-4702) for the Ford 2.0-litre Zetec-E, four cylinders, 16 valves.

  • Brand: ARP
  • Engines: EDDB, EDDC, EDDD, EDDF
  • Thread: M10
  • Grade: 8740
ARP-251-4702
1 in stock in Europe (72h lead time)
Pay in installments

The engines concerned

Ford's 2.0-litre Zetec-E (codes EDDB, EDDC, EDDD and EDDF) is a 1,988 cc in-line four-cylinder (84.8 mm bore, 88.0 mm stroke) with 16 valves and twin overhead camshafts. It powers the first-generation Ford Focus, as a hatchback, a saloon and a Turnier estate.

As standard, the cylinder head of this engine is held down by cylinder head bolts, which the ARP studs replace.

Reinforced ARP cylinder head studs

The job of the head fasteners is to keep the cylinder head locked to the block despite the pressure inside the combustion chambers. They keep the gasket compressed; as soon as their clamping force drops, leaks appear between head and block.

The ARP 251-4702 kit is made of 8740, 10 mm in diameter. According to its instruction sheet, the studs are screwed into the block by hand before the head is fitted; the threads, washers and nuts, lubricated with ARP Ultra-Torque, are then tightened in three equal passes. Material of the fasteners: 8740, a chrome-molybdenum steel that ARP specifies at 200,000 psi tensile strength. Factory-fitted fasteners usually fall into classes 10.9 and 12.9, with 150,800 to 176,900 psi minimum tensile strength. In M10, the 8740 studs hold up to 500 hp on this four-cylinder engine (calculated estimate).

Technical specifications

Part number Brand Grade / material Nuts Thread
ARP-251-4702 ARP 8740 - Undercut 12-point M10

Tightening torque

Part number Stage 1 Stage 2 Stage 3
ARP-251-4702 27 Nm 54 Nm 81 Nm

The studs are fitted into the block by hand, without a torque wrench. For a permanent installation, the instruction sheet accepts thread locker, with tightening to be completed before it sets.

According to the sheet, ARP thread sealer is applied to the block-side threads where the studs open into the water jacket.

Follow the tightening sequence recommended by the manufacturer and bring to torque in three stages; the stated values assume ARP lubricant on the threads and under the nuts.

The washers also receive ARP lubricant, as stated in the instruction sheet.

The torque figures above come from ARP instruction sheet 251-4702, revision applicable on the day the page went online. The official instruction sheet prevails in case of difference and describes the complete procedure, tightening sequence included. Read the ARP 251-4702 instruction sheet

Technical guide

The stated tightening torques only make sense with ARP assembly grease, applied to the threads and under the nuts.

Buy the ARP assembly grease →

ARP undercut studs

The undercut version is recognisable by its reduced shank between the threads. According to ARP, this profile equalises stretch from one stud to the next and makes the clamping more consistent, while compensating for head gasket compression during installation: engine sealing benefits.

The ARP brand

ARP Gary Holzapfel, a former aerospace engineer, created ARP (Automotive Racing Products) in the early 1970s to tackle engine failures caused by insufficiently strong fasteners in racing. Today the brand develops and manufactures thousands of parts in California, available in several material grades as needed.

Advantages over the original bolts

Criterion Original head bolts Reinforced ARP studs
Original Ford cylinder head bolts Reinforced ARP studs
Block threads Stressed at every tightening Spared by hand-tight fitting

When studs become necessary

On an engine left standard, the original fasteners do their job. Switching to reinforced fasteners becomes worthwhile as soon as:

  • EDDB, EDDC, EDDD or EDDF built for fast road or track use (turbo kit, modified engine map)
  • The compression ratio is increased
  • A reinforced MLS gasket is fitted, with its need for a high and even preload
  • The head has already lifted or the gasket has already failed
  • The engine is used in competition, with intense heat cycles and repeated teardowns

Vehicle compatibility

Model Engine code Power Years
Ford Focus I hatchback (DAW, DBW) EDDB, EDDC, EDDD, EDDF 126-131 hp 1998-2005
Ford Focus I saloon (DFW) EDDB, EDDC, EDDD, EDDF 126-131 hp 1999-2005
Ford Focus I Turnier estate (DNW) EDDB, EDDC, EDDD, EDDF 131 hp 1999-2004

Why is it the most cost-effective solution?

A standard Zetec-E works with a safety margin set for series output. As soon as a remap, a turbo kit or a higher compression ratio pushes up cylinder pressure, the head and the gasket are the first parts to suffer. A set of ARP 8740 studs keeps the head pressed down with a steadier clamping load; reopening an engine for a blown gasket costs far more than this kit.

Consider a reinforced head gasket

To get the most out of reinforced fasteners, pair them with a head gasket that withstands the same pressure. Here is the gasket we offer for this engine:

Reinforced head gasket Ford Focus Zetec-E EDDB EDDC EDDD EDDF →

  • Brand
    ARP
  • Reference
    ARP-251-4702
  • EAN13
    0672036023263

9 other products in the same category

Viewed products

Loading...