Skip to content
NSB Concept

Reinforced ARP bolts for OEM rods FORD Zetec

€86.10 (tax incl.)
€101.29 (tax incl.) -15%

ARP 8740 steel rod bolt kit for the OEM rods of the Ford Zetec 2.0 16V engines (Mondeo, Focus, Cougar, Contour, Mystique, Escape).

  • Brand: ARP
  • Engines: NGA, NGB, NGC, NGD, EDDB, EDDC, EDDD, EDDF, EDBA, EDBB, EDBC, EDBD
  • Thread: M9
  • Grade: 8740
ARP-151-6005
1 in stock in Europe (72h lead time)
Pay in installments

The Ford Zetec 2.0 engine concerned

The Zetec 2.0 is Ford's 2.0-litre four-cylinder with 16 valves (1,988 cc); the NGK catalogue lists it under codes NGA to NGD on the 1993 to 2001 Mondeo, and under codes EDDB, EDDC, EDDD and EDDF on the first-generation Focus from 1998 to 2005; it also powers the European Cougar (codes EDBA to EDBD, 1998-2001) and Ford and Mercury models sold in North America (Contour, Mystique, Cougar, Focus, Escort ZX2, Escape).

This kit replaces the original rod bolt of this four-cylinder: ARP describes it as a set of rod cap screws, without washer, for the Ford 2.0 L Zetec (M9).

Reinforced ARP bolts for connecting rods

At every engine revolution, the rod and piston assembly pulls on the rod cap, and only its bolts hold it against these inertia loads. The original ones are intended for stock power and for a single installation.

This 8740 steel kit fits in place of the original bolts of the standard rods. For tightening, ARP favours measuring the stretch; without a gauge, the instruction sheet gives a torque of 48.8 Nm. These bolts are made from 8740, a chrome-moly steel brought to 180,000 psi tensile strength by ARP's heat treatment; the threads are rolled afterwards. For comparison, classes 10.9 and 12.9 of original fasteners have a minimum of 150,800 to 176,900 psi. The 8740 bolts hold up to 9,500 rpm (calculated estimate).

Technical specifications

Part numberBrandGrade / materialHeadThreadUnder-head length
ARP-151-6005 ARP 8740 steel Not published M9 Not published

Before fitting the bolts, the ARP instruction sheet asks you to check that the bolt hole of the rod cap has an adequate chamfer to clear the radius under the head.

Tightening torque and stretch

ReferenceTightening torqueStretch
ARP-151-6005 48.8 Nm 0.114 - 0.127 mm

ARP gives priority to stretch control for an accurate preload; the torque in the table is used only when no gauge is available. Torque and stretch figures in the table apply with ARP lubricant.

The values above come from the ARP 151-6005 instruction sheet applicable at the date of publication; it is authoritative in the event of any difference. Read the ARP 151-6005 instruction sheet

The ARP instruction sheet does not require a thread locker for this kit; only ARP Ultra-Torque grease is applied, on the threads as well as under the bolt head.

According to the ARP instructions, the big ends must be checked and resized with the fasteners in place; plan a visit to a machine shop.

Measuring bolt stretch

Measuring the stretch of a rod bolt

Tightening to stretch means setting the preload on how much the bolt actually stretches, rather than on a torque affected by friction. With the bolt fitted, the dial gauge is placed on both its ends and the bolt is tightened until the stretch given in the table is read. It is the safest method on a highly tuned engine.

Technical guide

Torque and stretch figures are only valid with ARP assembly grease, applied to the threads and under the head.

The ARP brand ARP

ARP (Automotive Racing Products) came into being in the early 1970s, when Gary Holzapfel, who came from the aerospace industry, decided to tackle the engine failures caused in motorsport by inadequate fasteners. Today the brand produces thousands of part numbers in California for the cylinder head, the main bearings and the connecting rods, in materials suited to each application, with manufacturing known for its consistency.

Vehicle compatibility

BrandModel (chassis)Engine codePowerYears
Ford Mondeo I (GBP) 2.0 i 16V, Hatchback NGA 132 to 136 hp 1993-1996
Ford Mondeo I (GBP) 2.0 i 16V, Saloon NGA 132 to 136 hp 1993-1996
Ford Mondeo I (BNP) 2.0 i 16V, Estate NGA 132 to 136 hp 1993-1996
Ford Mondeo II (BAP) 2.0 i, Hatchback NGA, NGB, NGC, NGD 131 hp 1996-2000
Ford Mondeo II (BFP) 2.0 i, Saloon NGA, NGB, NGC, NGD 131 hp 1996-2000
Ford Mondeo II (BNP) 2.0 i, Estate NGA, NGB, NGC, NGD 131 hp 1996-2000
Ford Focus I (DAW, DBW) 2.0 16V, Hatchback EDDB, EDDC, EDDD, EDDF 126 to 131 hp 1998-2005
Ford Focus I (DFW) 2.0 16V, Saloon EDDB, EDDC, EDDD, EDDF 115 to 131 hp 1999-2005
Ford Focus I (DNW) 2.0 16V, Estate EDDB, EDDC, EDDD, EDDF 131 hp 1999-2004
Ford (Australia) Mondeo (HA-HD) 2.0, Hatchback NGA, NGB, NGC, NGD 128 to 131 hp 1995-2000
Ford (Australia) Mondeo (HE) 2.0, Hatchback NGA, NGB, NGC, NGD 128 hp 2000-2001
Ford (Australia) Mondeo (HA-HD) 2.0, Saloon NGA, NGB, NGC, NGD 128 to 132 hp 1995-2000
Ford (Australia) Mondeo (HE) 2.0, Saloon NGA, NGB, NGC, NGD 128 hp 2000-2001
Ford (Australia) Mondeo (HA-HC) 2.0 i, Estate NGA, NGB, NGC, NGD 128 to 132 hp 1995-1998
Ford (Australia) Focus (LR) 2.0, Hatchback EDDB, EDDD 116 to 131 hp 2002-2005
Ford (Australia) Focus (LR) 2.0 i, Saloon EDDB, EDDD 116 to 131 hp 2002-2005
Ford (USA) Contour 2.0, Saloon ZH993 126 hp 1993-1997
Ford (USA) Contour 2.0, Saloon ZH993 126 to 131 hp 1997-2000
Ford (USA) Escort ZX2 2.0, Coupe D93 132 hp 1997-2003
Ford (USA) Focus 2.0, Hatchback Zetec 2.0 132 hp 1999-2004
Ford (USA) Focus 2.0, Saloon C20HDEZ 132 hp 1999-2004
Ford (USA) Focus 2.0, Estate Zetec 2.0 132 hp 1999-2004
Ford (USA) Escape 2.0, SUV T20HDEZ, ZH20GYF 124 to 129 hp 2001-2004
Mercury Mystique 2.0, Saloon 99520 126 to 131 hp 1994-2001
Mercury Cougar 2.0, Coupe ZH993 126 hp 1998-2002
Ford Cougar (EC) 2.0 16V, Coupe EDBA, EDBB, EDBC, EDBD 131 hp 1998-2001
Important: This kit is reserved for the 16-valve Zetec 2.0 four-cylinder listed in the table (codes NGA, NGB, NGC, NGD, EDDB, EDDC, EDDD, EDDF, EDBA, EDBB, EDBC and EDBD) and for original rods: the ARP application does not cover the other displacements of the Zetec family.

Why is it the most cost-effective solution?

Pushing a Zetec 2.0 beyond stock exposes every rod bolt to repeated inertia loads: if one gives way, the rod, the piston and often the block are lost. An ARP 8740 kit costs a fraction of a bottom-end rebuild and removes that weak point.

  • Brand
    ARP
  • Reference
    ARP-151-6005
  • EAN13
    0672036020514

9 other products in the same category

Viewed products

Loading...