Skip to content
  • On order
Reinforced ARP cylinder head studs FORD Pinto 2.0 Reinforced ARP cylinder head studs FORD Pinto 2.0 Reinforced ARP cylinder head studs FORD Pinto 2.0 Reinforced ARP cylinder head studs FORD Pinto 2.0

Reinforced ARP cylinder head studs FORD Pinto

€164.19 (tax incl.)
€193.16 (tax incl.) -15%

ARP 8740 cylinder head stud kit (151-4201) for the Ford 2.0-litre Pinto, four cylinders, 8 valves.

  • Brand: ARP
  • Engines: Pinto 2.0
  • Thread: M12
  • Grade: 8740
ARP-151-4201
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

The engines concerned

Ford's 2.0-litre Pinto is a 1,993 cc in-line four-cylinder (90.8 mm bore, 77 mm stroke) with eight valves and an overhead camshaft. It powered the Ford Sierra, Capri, Granada and Escort RS 2000 from 1972 to 1993.

As standard, the cylinder head of the Pinto 2.0 is secured by cylinder head bolts, which the ARP studs replace.

Reinforced ARP cylinder head studs

Every combustion cycle pushes the cylinder head upwards. The head fasteners resist it by keeping a constant clamping pressure on the gasket; if that pressure drops, the seal is no longer guaranteed.

The 151-4201 is an 8740 kit, 12 mm in diameter. Its instruction sheet calls for ARP Ultra-Torque on the threads, washers and nuts, each stud to be run into the block by hand before the head goes on, and the nuts to be tightened in three equal passes. Material of the fasteners: 8740, a chrome-molybdenum steel that ARP specifies at 200,000 psi tensile strength. Factory-fitted fasteners usually fall into classes 10.9 and 12.9, with 150,800 to 176,900 psi minimum tensile strength. In M12, the 8740 studs hold up to 600 hp on this four-cylinder engine (calculated estimate).

Technical specifications

Part number Brand Grade / material Nuts Thread
ARP-151-4201 ARP 8740 12-point M12

Tightening torque

Part number Stage 1 Stage 2 Stage 3
ARP-151-4201 41 Nm 81 Nm 122 Nm

The studs are fitted into the block by hand, without a torque wrench. For a permanent installation, the instruction sheet accepts thread locker, with tightening to be completed before it sets.

The sheet also calls for ARP thread sealer on the block-side threads where the studs break into the water jacket.

Follow the tightening sequence recommended by the manufacturer and bring to torque in three stages; the stated values assume ARP lubricant on the threads and under the nuts.

According to the instruction sheet, ARP lubricant is also applied to the washers, as on the threads.

Source of these values: ARP instruction sheet 151-4201, revision current at the time of publication. The official instruction sheet applies if any discrepancy appears; it covers the entire procedure and the tightening sequence. Read the ARP 151-4201 instruction sheet

Technical guide

The stated tightening torques only make sense with ARP assembly grease, applied to the threads and under the nuts.

Buy the ARP assembly grease →

The ARP brand

ARP ARP (Automotive Racing Products) was born in the early 1970s from the initiative of Gary Holzapfel, an engineer from the aerospace industry, determined to eliminate engine failures caused by weak fasteners in motorsport. The company designs and manufactures thousands of parts in California, in several material grades suited to each use.

Advantages over the original bolts

Criterion Original head bolts Reinforced ARP studs
Original Ford cylinder head bolts Reinforced ARP studs
Block threads Stressed at every tightening Spared by hand-tight fitting

When studs become necessary

The original fasteners are sized for the engine as it leaves the factory. They need to be reinforced when:

  • Pinto 2.0 built for fast road, rally or track use (turbo, raised compression ratio)
  • The compression ratio rises as the build progresses
  • The original gasket is replaced by a reinforced MLS gasket, which requires a high and uniform preload
  • The engine has already suffered a lifted head or a gasket leak
  • Competition use imposes severe heat cycles and regular head removals

Vehicle compatibility

Model Engine code Power Years
Ford Sierra I 2.0 (GBC, BNC) Pinto 2.0 100-115 hp 1982-1986
Ford Sierra II 2.0 (GBC, GBG, BNG) Pinto 2.0 100-115 hp 1987-1993
Ford Capri II and III 2.0 Pinto 2.0 98-101 hp 1974-1985
Ford Granada II and Turnier 2.0 (GU, GNU) Pinto 2.0 101-105 hp 1979-1985
Ford Escort II RS 2000 (ATH) Pinto 2.0 100-110 hp 1973-1980
Ford Escort I RS 2000 Pinto 2.0 99 hp 1972-1974
Ford Taunus 2.0 Pinto 2.0 87-100 hp 1976-1982
Ford Transit 2.0 Pinto 2.0 59-90 hp 1977-1994
Ford Scorpio I 2.0 Pinto 2.0 100-115 hp 1985-1994
Ford P100 II 2.0 Pinto 2.0 78 hp 1987-1992

Why is it the most cost-effective solution?

A standard Pinto 2.0 runs with a reserve sized for series output. As soon as a turbo, a higher compression ratio or a competition build pushes up cylinder pressure, the head and its gasket move to the front line. With ARP 8740 studs the head stays clamped under a steadier load, and this kit costs far less than an engine stripped down for a blown gasket.

  • Brand
    ARP
  • Reference
    ARP-151-4201
  • EAN13
    0672036003371

3 other products in the same category

Viewed products

Loading...