Skip to content
  • On order
Reinforced head gasket Ford Pinto 2.0 - H1267SPL051S Reinforced head gasket Ford Pinto 2.0 - H1267SPL051S

Reinforced cylinder head gasket Ford Pinto 2.0 8V NE NER NES N4A

€113.60 (tax incl.)
€151.46 (tax incl.) -25%

Reinforced Cometic multi-layer steel (MLS) head gaskets for Ford Pinto 2.0 engines. Sold individually.

  • Engines: NE, NEE, NEG, NEK, NEN, NEP, NER, NES, NET, NE5, NEJ, NR2, NRB, NRD, N4A, N4B, N4I, TL20LC, TL20LNM
  • Bore: 92.5 to 101 mm
  • Thickness: 0.76 to 3.05 mm
  • Replaces: 6 816 643
H1267SPL051S (170335)
0 in stock in France
For larger quantities, 5 to 15 days lead time
Pay in installments

The Ford engines covered

The 2.0-litre 8-valve Ford petrol engines NE, NEE, NEG, NEK, NEN, NEP, NER, NES, NET, NE5, NEJ, NR2, NRB, NRD, N4A, N4B, N4I, TL20LC and TL20LNM power the Ford Capri III, Consul, Escort II, Granada, Scorpio I, Sierra I and II and Taunus, listed below.

The original gasket of these engines carries the part number 6 816 643. Ford publishes neither its bore, nor its thickness, nor its construction. Calibrated for standard combustion pressure, it lets the cylinder head loosen and lift as soon as that pressure rises, and coolant reaches a cylinder.

Reinforced cylinder head gaskets

How well the gasket holds also depends on the fasteners: bolts or studs must press the head firmly onto the block. A composite gasket is crushed for good beyond 100 N/mm² of permissible stress, whereas the 301 stainless steel of MLS gaskets withstands 517 N/mm², 5 times more, and springs back with every combustion.

This page offers seven part numbers from the American maker Cometic, a specialist in racing gaskets, all in multi-layer steel MLS: five bores from 92.5 to 101 mm and five thicknesses from 0.76 to 3.05 mm. Each is sold individually.

Technical specifications

Gasket bore Thickness Gasket volume Gasket type
OEM not specified
Brand Part number
OEM 6 816 643
92.5 mm 1.02 mm 6.85 MLS Cometic H1267040S
92.5 mm 1.14 mm 7.66 MLS Cometic H1267045S
93.5 mm 0.76 mm 5.22 MLS Cometic H1267SP6030S
93.5 mm 1.30 mm 8.93 MLS Cometic H1267SP6051S
94.5 mm 3.05 mm 21.39 MLS Cometic H1267SP1120S
96 mm 1.30 mm 9.41 MLS Cometic H1267SPL051S
101 mm 1.14 mm 9.13 MLS Cometic H1267SPM045S

A head gasket leaves a small free volume above each piston, which adds to the combustion chamber: the larger it is, the lower the compression ratio. Only compare these volumes between gaskets of the same bore.

Preparation and fitting

Fasteners Engines Tightening torque
Original cylinder head bolts NE, NEE, NEG, NEK, NEN, NEP, NER, NES, NET, NE5, NEJ, NR2, NRB, NRD, N4A, N4B, N4I, TL20LC, TL20LNM not published by the manufacturer

Before fitting, check the flatness of the head and block with a straightedge and have whichever needs it resurfaced. The Cometic gasket arrives already coated: do not add any sealant to it.

Reinforced ARP cylinder head studs Ford Pinto 2.0 →

Technical guide

The construction offered

Cometic MLS cylinder head gasket MLS Cometic
Several stainless steel sheets, embossed and riveted together. Active beads surround each cylinder and each fluid passage on the outer sheets. Sealing is achieved with moderate clamping load and little bore distortion. It is a versatile choice, from the tuned naturally aspirated engine to the mild turbo.

Choosing bore and thickness

Gasket bore. The Cometic MLS is offered in five bores: 92.5 mm (H1267040S and H1267045S), 93.5 mm (H1267SP6030S and H1267SP6051S), 94.5 mm (H1267SP1120S), 96 mm (H1267SPL051S) and 101 mm (H1267SPM045S).

Thickness. Ford gives no thickness for the original gasket of these engines. A thicker gasket enlarges the combustion chamber and lowers the compression ratio; a thinner one reduces it and raises the ratio.

Your goal Thickness to choose
Keep the original compression ratio Original thickness not published: measure the removed gasket and compare it with the five thicknesses offered, from 0.76 to 3.05 mm
Skimmed cylinder head, make up the lost height Five thicknesses are offered, from 0.76 to 3.05 mm: compare them with that of the removed gasket, plus the material taken off when resurfacing
Forced induction build, lower the ratio A thickness greater than the one measured on the original gasket at removal, up to 3.05 mm
Naturally aspirated build, raise the ratio A thickness smaller than the one measured on the original gasket at removal, down to 0.76 mm

As the original thickness is not published, use a dial gauge to measure how far the pistons stand above the block deck, especially if you choose a gasket thinner than the removed one: this figure sets the clearance left between piston and cylinder head.

The brand

Cometic Cometic Gasket, Inc. is an American maker of engine sealing gaskets, founded in 1989 and based in Concord, Ohio. It makes to order, at the bore and thickness required, and manufactures entirely in the United States from American materials.

Advantages over the original gasket

Criterion Original gasket 6 816 643 Reinforced gaskets
Construction Construction not specified by the manufacturer Multilayer stainless steel (MLS)
Gasket bore not published 92.5 to 101 mm
Thicknesses available not published by the manufacturer 0.76 to 3.05 mm, 5 values
Compression ratio adjustment None Through the thickness chosen
Resistance to overpressure Limited to standard output Designed for forced induction

When a reinforced gasket becomes necessary

  • Adding forced induction, or raising boost on an already turbocharged engine
  • Cylinder rebored beyond what the largest bore, 101 mm, of the gaskets offered covers
  • Looking for a compression ratio different from standard, higher or lower
  • Engine that has already lost its gasket, or is consuming coolant
  • Competition use, where the gasket goes through repeated temperature rises

Vehicle compatibility

Model Engine code Power Years
Ford Escort II 2.0 RS NE 100 and 110 hp 1973-1980
Ford Consul 2000 NE 99 hp 1972-1975
Ford Taunus 2000 NEE / NEG 98 hp 1973-1976
Ford Taunus 2.0 NEG 95 and 98 hp 1976-1979
Ford Taunus V 2.0 (dont Turnier) NER 87 and 100 hp 1979-1982
Ford Granada I 2.0 TL20LC 99 hp 1975-1975
Ford Granada 2.0 TL20LC 95 hp 1976-1977
Ford Granada II 2.0 TL20LC 87 hp 1977-1979
Ford Granada II 2.0 NEP 101 hp 1979-1985
Ford Granada II 2.0 NEK 105 hp 1981-1985
Ford Scorpio I 2.0 i NER 100 hp 1985-1990
Ford Capri III 2.0 NEN 101 hp 1978-1985
Ford Capri III 2.0 TL20LNM 87 hp 1978-1985
Ford Sierra I 2.0 NRD 100 hp 1985-1986
Ford Sierra I 2.0 NET 105 hp 1982-1986
Ford Sierra I 2.0 i NR2 / NRB 115 hp 1985-1986
Ford Sierra I 2.0 i Köln N4B 100 hp 1983-1987
Ford Sierra II 2.0 NES 105 hp 1987-1993
Ford Sierra II 2.0 i NE5 / NEJ 100 hp 1987-1993
Ford Sierra II 2.0 i Cat N4B 100 hp 1987-1993
Ford Sierra II 2.0 i N4A / N4I 115 hp 1987-1993

OEM part number: 6 816 643.

Important: the part numbers on this page apply to the Pinto engines of the table above: read your vehicle's engine code, then check that the bore of the gasket you choose suits that of your engine before ordering.

Why switch to a reinforced gasket?

When the original gasket has reached its limit, the reinforced gasket takes over: at a higher combustion pressure it does not crush and keeps its shape.

As soon as more power is asked of this engine, through tuning, ignition or compression, the head gasket is the first part to suffer. A reinforced gasket rules out the leak, at a cost far below that of pulling the head and the downtime that follows.

3 other products in the same category

Viewed products

Loading...