Skip to content
  • In stock
ACL trimetal connecting rod bearings Porsche 911 2.3 2.7 3.0 ACL trimetal connecting rod bearings Porsche 911 2.3 2.7 3.0

ACL trimetal connecting rod bearings Porsche 911 2.3 2.7 3.0

€98.22 (tax incl.)
€109.13 (tax incl.) -10%

Set of 12 trimetal connecting rod half-bearings for Porsche 911 2.3, 2.7 and 3.0.

  • Brand and treatment: ACL Race
  • Compatibility: 911 2.3 / 2.7 / 3.0, 911 Turbo 3.0
  • Engine codes: codes in the compatibility table
  • Available sizes: standard to +0.25 mm, increased-clearance version (HX)
6B2455H-STD
30 in stock in Europe (72h lead time)
Pay in installments

The Porsche 911 2.3, 2.7 and 3.0 flat-six engines

The 2.3 and 2.7-litre 911 engines, together with the 3.0-litre of the 911 Carrera and 911 Turbo (930.02, 930.50 and 930.52), are air-cooled flat-sixes producing 130 to 260 hp. ACL lists the same bearing set for all these engines: a single set covers the family.

From the factory, this engine is fitted with standard production connecting rod bearings, sized for the loads of the original engine: as soon as power, engine speed or boost pressure increase, they reach their limits.

Trimetal connecting rod bearings

Three layers make up a trimetal bearing: the steel back for stiffness, the copper-lead intermediate layer for load capacity, then the anti-friction running layer that protects the crankpin. This set includes 12 half shells, that is 6 pairs.

Where an aluminium bi-metal bearing, designed for low to medium loads, withstands about 8,000 psi, a performance trimetal bearing goes up to 12,000 psi: 50% extra margin. That is what keeps it durable on an engine boosted by a turbo or supercharger, or pushed to high rpm.

Technical specifications

Fitment dimensions common to all references
ACL bearings
Crankpin Ø 51.971 / 51.990 mm
Housing bore Ø 56.000 / 56.019 mm
Width 19.8 mm
ReferenceBrand and treatmentSizeWall thickness (mm)
6B2455H-STD ACL Race - Untreated Standard 1.990
6B2455HX-STD ACL Race - Untreated Std, increased clearance (HX) 1.977
6B2455H-.025 ACL Race - Untreated +0.025 2.003
6B2455H-.25 ACL Race - Untreated +0.25 2.115

Running clearance

Between the crankpin and the bearing there is a small gap, the running clearance, in which the oil film circulates.

In operation there is no metal-to-metal contact: the crankpin turns on this oil film, which supports the whole load. The clearance determines its thickness. A clearance that is too tight hinders oil flow, heats the assembly and promotes seizure; one that is too wide lets oil leak away, weakens the film and makes oil pressure drop. The correct clearance balances oil flow and film strength.

Size / gradeWhen to choose itACL Race Series
Standard (STD) Standard journal, not reground 0.055 to 0.065 mm
Increased clearance (HX) Wider clearance: high oil flow, high rpm 0.080 to 0.090 mm
+0.025 mm Polished journal 0.055 to 0.065 mm
+0.25 mm Journal reground to 0.25 mm 0.055 to 0.065 mm

Checking on assembly: lay a calibrated strip (Plastigauge) on the journal, torque the rod cap to spec, then compare the crushed strip against the gauge to read the clearance.

Plastigauge

Order the Plastigauge →

Technical guide

Designed for engine building and motorsport, these ACL trimetal connecting rod bearings carry much more load than an original bearing, whether the engine gains power, revs higher or receives a turbo or supercharger. They are available in several sizes: the standard size, a +0.025 mm size for a crankpin that has only been polished, a +0.25 mm regrind size and the HX version with increased clearance for high-revving engines or engines needing a high oil flow. That makes it possible to put a reground crankshaft back into service without changing range and to set the clearance for the oil and use.

The brand

ACL Bearing Company ACL Bearing Company has been making high-performance engine bearings in Australia since 1949. Its Race Series offers precise trimetal bearings, available in many sizes and proven in tuned and racing engines worldwide.

Vehicle compatibility

This connecting rod bearing set fits the 911 2.3, 2.7 and 3.0 flat-six engines of the following Porsche models:

BrandModel (chassis)Engine codePowerYears
PORSCHE 911 2.3 E 911.52 165 hp 1971–1973
PORSCHE 911 2.3 S 911.53, 911.63 190 hp 1971–1973
PORSCHE 911 2.3 T 911.51, 911.57, 911.61, 911.67, 911.91, 911.96 130–140 hp 1971–1973
PORSCHE 911 2.7 911.41, 911.43, 911.46, 911.48, 911.81, 911.82, 911.84, 911.85, 911.86, 911.89, 911.90, 911.92, 911.94, 911.97, 911.99 150–165 hp 1973–1977
PORSCHE 911 2.7 S Carrera 911.42, 911.47, 911.93, 911.98 175 hp 1973–1976
PORSCHE 911 2.7 SC Carrera RS 911.83 209 hp 1972–1979
PORSCHE 911 3.0 SC Carrera 930.02 200 hp 1975–1977
PORSCHE 911 3.0 Turbo 930.50, 930.52 260 hp 1975–1977
PORSCHE 911 Targa 2.3 E 911.52 165 hp 1971–1973
PORSCHE 911 Targa 2.3 S 911.53, 911.63 190 hp 1971–1973
PORSCHE 911 Targa 2.3 T 911.51, 911.57, 911.61, 911.67, 911.91, 911.96 130–140 hp 1971–1973
PORSCHE 911 Targa 2.7 911.41, 911.43, 911.46, 911.48, 911.81, 911.82, 911.84, 911.85, 911.86, 911.89, 911.90, 911.92, 911.94, 911.97, 911.99 150–165 hp 1973–1977
PORSCHE 911 Targa 2.7 S 911.42, 911.47, 911.93, 911.98 175 hp 1973–1976
PORSCHE 911 Targa 2.7 SC Carrera RS 911.83 209 hp 1972–1979
PORSCHE 911 Targa 3.0 SC Carrera 930.02 200 hp 1975–1977

Why replace the bearings

When a connecting rod bearing gives way, the damage quickly spreads beyond the part itself: a scored crankpin, debris carried through the whole oil circuit, a crankshaft to regrind at the very least, sometimes a rod and block lost. A bearing set costs far less than a regrind and is nothing compared with a complete engine rebuild. It is the cheapest part of the rotating assembly, yet the one whose failure is most expensive.

5 other products in the same category

Viewed products

Loading...