Skip to content
  • On order
Reinforced valve spring sets PSA XU9J4 XU9J4Z XU10J4 Reinforced valve spring sets PSA XU9J4 XU9J4Z XU10J4

Reinforced valve spring kit PSA XU9J4 XU9J4Z XU10J4

€430.08 (tax incl.)
€537.60 (tax incl.) -20%

Valve spring set of 16 reinforced springs for the PSA 1.9 and 2.0 16V engines XU9J4, XU9J4Z and XU10J4.

  • Brands: CATCAMS
  • Engines: XU9J4, XU9J4Z, XU10J4 (16V)
  • Springs: single
  • Contents: springs and upper retainers
PAC-S10011*16+99333*16
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

The XU9J4, XU9J4Z and XU10J4 engines of Peugeot and Citroën

The XU9J4 and XU9J4Z (1.9 litre) and the XU10J4 (2.0 litre) are sixteen-valve four-cylinders of the XU family, found in the Peugeot 306 S16, 309 GTI and 405 Mi16 and the Citroën ZX 16V. With four valves per cylinder, the kit contains 16 springs.

Neither the collets nor the lower spring seats are touched: the springs and upper retainers are the only parts that change.

CATCAMS reinforced valve spring set

A valve spring shuts the valve against its seat, then holds it pressed on the cam. Once revs climb, the moving mass of valve, retainer and collets outweighs what the spring can control: the valve leaves the cam, bounces back and may touch the piston.

This CATCAMS valve spring set contains 16 PAC-S10011 springs and 16 upper retainers 99333: 392 N at the seat at 37.0 mm and 1030 N at 13.0 mm of lift. The standard collets and lower spring seats are not replaced.

Valve spring kit technical specification

Part numberBrandSpringsOuter / inner ØSeat pressureOpen pressureRateMax liftKit contents
PAC-S10011*16+99333*16 CATCAMS Single 392 N at 37.0 mm 1030 N at 13.0 mm 16 springs, 16 upper retainers

Valve spring kit fitting details

PartPSA originalReinforced spring kit
Spring Kit specific: PAC-S10011 (CATCAMS)
Retainer Kit specific: 99333 (CATCAMS)
Spring seat Original kept
Collets Original kept

The kit supplied contains 16 single springs PAC-S10011 and 16 upper retainers 99333; factory spring seats and collets do not change.

Installed height is the distance read between upper and lower retainer with the valve at rest; a load is valid only for the height quoted with it. When the seats are machined, the gap between retainers grows and the load loses as many newtons as the spring rate shows per millimetre gained. After machining, measure all 16 valves and compare with the table.

CATCAMS
Installed height 37.0 mm
Seat pressure at this height 392 N

Technical guide

Our brands

CATCAMS CATCAMS, a Belgian firm (Cat Cams N.V.), designs competition camshafts shipped worldwide. Its numerically controlled grinder even cuts inclined lobes, and the springs are developed for these shafts, which have been entered in the BTCC and at Le Mans.

How to choose

A higher load keeps the valve against its cam as revs climb: it allows a more aggressive camshaft, a higher rev limit or a turbo, without the valve leaving the cam. At 13.0 mm of lift, CATCAMS quotes 1030 N for this kit. Since maximum lift is not supplied, ask CATCAMS to confirm the lift of any camshaft you plan to use before buying.

CriterionKey point
Choosing the pressure The kit has a single load level: 392 N at the seat at 37.0 mm. To judge whether it suits your build, weigh up the profile of your camshaft, the revs you are targeting and any turbo; chasing more load than needed is pointless, as the excess wears the cams and the valvetrain. CATCAMS gives no load figure for the original springs, so no percentage gain is claimed. Excess load also adds friction and wear.
Single or double spring This kit combines the single spring PAC-S10011 with the upper retainer 99333: no double spring is included, so no inner spring needs planning for. A valve takes one spring, and the kit is fitted with the retainer supplied.

When reinforced springs become necessary

  • Camshaft with more lift or duration than standard
  • Higher peak revs after engine changes
  • Turbo or supercharger fitted
  • Head built for track or hill climbs
  • Tired springs, or valves floating near the limiter

Compatible vehicles

ModelEngine codePowerYears
Peugeot 306 S16 ACAV XU10J4 155 hp 1993-2001
Peugeot 309 GTI XU9J4 158 hp 1989-1990
Peugeot 309 GTI XU9J4Z 147 hp 1990-1993
Peugeot 405 Mi16 XU9J4 158 hp 1987-1992
Peugeot 405 Mi16 XU9J4Z 147 hp 1987-1992
Peugeot 405 Mi16 XU10J4Z 152 hp 1992-1995
Citroën ZX 2.0 16V XU10J4 152 hp 1992-1994
Important: this kit is reserved for the XU9J4, XU9J4Z and XU10J4. The other PSA engines (TU, EW, other XU) take different part numbers: check the engine code before ordering.

Related products

With the head on the bench, renew the inlet and exhaust valves and the guides as well: firmer springs and fresh sealing then work together.

PSA XU9J4 inlet valves →
PSA XU9J4 exhaust valves →

12 other products in the same category

Viewed products

Loading...