Skip to content
  • On order
Reinforced ARP main studs for Ford Zetec-E 2.0 Silvertop Reinforced ARP main studs for Ford Zetec-E 2.0 Silvertop

Reinforced ARP main studs for FORD Zetec-E Silvertop

€124.76 (tax incl.)
€146.77 (tax incl.) -15%

ARP 8740 steel crankshaft main studs for the Ford Zetec-E 2.0 Silvertop four-cylinder engine.

  • Brand: ARP
  • Engine: 2.0 16V (Zetec-E)
  • Thread: 7/16 inch
  • Grade: 8740
ARP-151-5406
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

The Ford engine concerned

This kit is for the 2.0-litre Ford Zetec-E four-cylinder, 16 valves, in its pre-1998 Silvertop version, found in the first and second-generation Mondeo and in the American Contour and Mercury Mystique.

Reinforced ARP studs for main bearings

The bottom end rests on its main bearings: combustion after combustion, the loads coming from the connecting rods end up on them. Under this stress the main cap tries to move on its parting line, which eventually brinells the mating faces and distorts the bearing bore.

The ARP studs in this kit, in 7/16 inch 8740 steel, take the place of the standard main cap fasteners of the Silvertop Zetec-E. After cleaning the block threads, they are fitted by hand. Once the caps are in place, washers and threads receive the ARP Ultra-Torque supplied with the kit, then the nuts are brought to torque in three equal passes, following the manufacturer's sequence: 36, 72 then 108 Nm. ARP rules out engine oil, which alters the friction and the clamping obtained.

Material: 8740, a chrome-moly steel that ARP specifies at 200,000 psi tensile strength, with threads rolled after heat treatment. Factory-fitted fasteners usually belong to classes 10.9 and 12.9, with 150,800 to 176,900 psi minimum tensile strength. The 8740 studs in 7/16 inch hold up to 1,200 hp on this four-cylinder engine (calculated estimate).

Technical specifications

Brand Grade / material Nut Thread
ARP 8740 steel ARP nut 7/16 inch

Tightening torque

Reference Pass 1 Pass 2 Pass 3
ARP-151-5406 36 Nm 72 Nm 108 Nm

Fitting the studs: screwed into the block by hand, without a tightening tool. If the assembly is to remain permanent, the ARP instruction sheet accepts a Loctite thread locker, with tightening carried through before the product cures.

The nuts are tightened in the sequence the manufacturer specifies for the main caps; the ARP instructions for the kit, linked below, describe the full procedure.

Moving to reinforced fasteners changes the clamping force on the caps. After installation, the size and roundness of the bores are checked, then align honed if needed, always with the final fasteners and lubricant.

Values taken from the ARP 151-5406 instruction sheet in force at the date of publication; the official instruction sheet prevails should any difference appear. Read the ARP 151-5406 instruction sheet

Technical guide

Tightening is done with ARP assembly grease: the torque figures in the table were established with it, not with engine oil.

Buy the ARP assembly grease →

The ARP brand

ARP Founded in the early 1970s by Gary Holzapfel, who came from the aerospace industry, ARP (Automotive Racing Products) set out to prevent fastener-related engine failures in motorsport. Its thousands of part numbers are designed and manufactured in California, in materials chosen for each use.

Advantages over the original bolts

Criterion Original main bolts ARP studs
Original main bearing cap bolt ARP main stud
Tightening Bolt screwed into the block, turning under torque Nut alone turns, tightened in three passes
Block thread Takes the rotation of the bolt at each assembly Stud placed by hand, no effort
Positioning the caps Cap to be held while screwing Cap guided by the studs

When studs become necessary

  • Silvertop Zetec-E 2.0 with forced induction or tuned for higher revs
  • Power well above the standard output
  • Bottom end opened for a rebuild
  • Main caps with play or tired block threads
  • Repeated sporting use, track, rally or drag

Vehicle compatibility

Model Engine code Power Years
Ford Contour (CDW27) Zetec-E 2.0 125 hp 1995-2000
Ford Mondeo Mk1 (CDW27) Zetec-E 2.0 (NGA) 136 hp 1993-1996
Ford Mondeo Mk2 (CDW27) Zetec-E 2.0 (NGA-NGD) 131 hp 1996-1998
Mercury Mystique (CDW27) Zetec-E 2.0 125 hp 1995-2000

Why is it the most cost-effective solution?

A Silvertop Zetec-E pushed beyond standard, through forced induction or higher revs, asks more of the main caps than the original fasteners were designed to give. These ARP studs steady the clamping at a cost out of all proportion to that of a bottom end to rebuild.

  • Brand
    ARP
  • Reference
    ARP-151-5406
  • EAN13
    0672036036393

5 other products in the same category

Viewed products

Loading...