Skip to content
  • On order
Reinforced inlet valves HONDA B18A B18B Reinforced inlet valves HONDA B18A B18B

Reinforced inlet valves HONDA B18A B18B

€208.42 (tax incl.)
€260.52 (tax incl.) -20%

Set of 8 reinforced inlet valves for HONDA B18A and B18B (Integra, Civic, Domani, Orthia).

  • Brand: SUPERTECH
  • Engines: B18A1, B18A2, B18B1, B18B2, B18B3, B18B4, B18B6
  • Dimensions: 31.0 mm or 31.5 mm head, 6.57 mm stem
  • Material: black nitride stainless steel
HIVN-1004-0-8
0 in stock in France
ORDER TODAY, WE SHIP IN 5 - 15 DAYS
Pay in installments

HONDA engines covered

The B18A and B18B are Honda's 1,834 cc 16-valve four-cylinder engines, from 131 to 146 hp depending on version. They power the Integra (DA9, DB1, DB7 and DC2 coupé), the Civic IV Shuttle 1.8, the Civic V and VI 180i, the Domani and the Orthia, from 1988 to 2001.

Each engine has 8 Honda 14711-PR4-A00 inlet valves (14711-P75-000 on the 1997 to 1999 B18B1), held by 14781-PL2-004 collets. Sharper camshafts, stiffer springs or a higher rev limit load them well beyond stock use.

SUPERTECH reinforced inlet valves

In a B18 pushed towards the red line, the inlet valve feeds fresh air to the cylinder and then blocks its way, several dozen times within one second. The head strikes its seat face in the head at each of its closings; the stem, meanwhile, never leaves the guide that centres it and slides there continuously. This part lives between 400 and 550 °C, whereas the chrome-silicon alloy fitted as original is already weakening there: it falls from 500 MPa at 500 °C to 250 MPa around 600 °C, just above that window, which takes away 50 % of its strength. Fitting a taller cam, uprated springs, extra rpm or a blower piles even more shock, friction and heat onto it.

At SUPERTECH these reinforced valves start out as a chrome-nickel stainless steel dedicated to racing, a cousin of EV8 (21-4N), which keeps 650 MPa at 500 °C and 550 MPa at 600 °C: 30 % then 120 % better than factory steel. The black nitride coating hardens and polishes their outside; the stem therefore rubs less in its guide and wears there far more slowly.

A +0.5 mm oversize is listed as well: the head measures 31.5 mm instead of 31.0 mm, with no change to stem or length. The seat then lets a more generous flow through, filling improves and power follows, provided the inlet seat faces are machined to this dimension.

Inlet valve technical specification

Part numberBrandSizeHead ØStem ØLengthGroovesMaterial
HIVN-1004-0-8 SUPERTECH Standard 31.0 mm 6.57 mm 105.4 mm Black nitride stainless steel
HIVN-1004-8 SUPERTECH +0.5 mm 31.5 mm 6.57 mm 105.4 mm Black nitride stainless steel

HIVN-1004-0-8: undercut stem under the head and back cut.

Fitting details

PartHONDA originalReinforced
Collets 14781-PL2-004
Valve stem seals 12210-PT2-003 / 12211-PT2-003
Valve guide 12204-PR4-A01

The +0.5 mm size needs inlet seats cut to 31.5 mm, workshop work to plan with the cylinder head rebuild.

Valve clearance is adjustable: after replacing the valves, check and set it (0.08 to 0.12 mm cold on the inlet side for the B18B1).

Technical guide

The brand offered

SUPERTECH SUPERTECH operates in San Jose, California, and has built everything that makes a racing valvetrain for more than 30 years. Each part number is drawn for a precise cylinder head, checked with ultrasound, then X-ray and laser beam, then signed off by tuners, from drag to track.

How to choose

The right size depends mostly on the condition of the head's inlet seat faces and on the airflow gain expected from the engine once built.

CriterionOption 1Option 2
Size Standard size
31.0 mm head, the factory one: suits inlet seat faces still in their original state, never recut.
+0.5 mm oversize
31.5 mm head: more air drawn in, hence extra power (about 10 to 12 cfm per mm of head). As for the seat faces, they must be machined to this size, if possible while widening the ports; also a valid answer for recovering previously reground seats.

When reinforced valves become necessary

  • High-lift camshafts, stiffened valve springs
  • Red line moved well higher
  • Supercharger or turbocharger added
  • Head prepared for track, hillclimb or rally
  • Factory valves damaged, worn or already recut once

Compatible vehicles

ModelEngine codePowerYears
Integra 1.8 (DA9) B18A1 / B18B1 131 hp 1989-1993
Integra 1.8 (DB1) B18A2 140 hp 1989-1993
Integra Coupé 1.8 (DC2) B18B1 / B18B2 137-146 hp 1993-2001
Integra 1.8 ESi (DB7) B18B2 145 hp 1993-2001
Civic IV Shuttle 1.8 (EE7) B18B6 131-140 hp 1988-1995
Civic V 180i (SR4) B18B3 132 hp 1994-1996
Civic VI 180i (SO4) B18B4 140 hp 1996-2000
Domani 1.8 (MA5) B18B6 140 hp 1992-1997
Orthia 1.8 (EL1 / EY4) B18B6 140 hp 1995-2001

OEM part number (inlet valve): 14711-PR4-A00; 14711-P75-000 (B18B1, 1997-1999)

Important: these sets are for the B18A and B18B; the VTEC B18C engines use other original valves (14711-PR3-000, 14711-P73-J01) and are not covered here. The Acura Integra is not covered on this page.

Related products

For a refreshed B18 head, it is wiser to replace the exhaust valves at the same moment as the inlet ones. We offer them for this engine here:

HONDA B18A B18B exhaust valves →

16 other products in the same category

Viewed products

Loading...