- In stock
SUPERTECH exhaust valve stem seals VAG 2.5 TFSI 2.5 20V
Set of 10 exhaust valve stem seals for VAG 2.5 TFSI and 2.5 20V five-cylinders, 6 mm stem.
- Brand: SUPERTECH
- Engines: CEPA, CEPB, CTSA, CZGB, DAZA, DNWA, BGP, BGQ, BPR, BPS, BTK, CBTA, CBUA, CCCA
- Material: Viton (FKM)
Audi, Volkswagen and KTM engines concerned
This set fits the exhaust side of VAG five-cylinder 20-valve engines with a 6 mm stem. On one hand the 2.5 TFSI of the Audi RS3 (8P and 8V), TT RS (8J and FV) and RS Q3 (8U and F3), codes CEPA, CEPB, CTSA, CZGB, DAZA and DNWA, also used in the KTM X-Bow GT-XR; on the other the naturally aspirated 2.5 20V of the Volkswagen Golf V and VI, Jetta III and IV, New Beetle, Beetle and Passat (A32), codes BGP, BGQ, BPR, BPS, BTK, CBTA, CBUA and CCCA.
The cylinder head carries 10 exhaust valves, two per cylinder. Each one gets an original seal that caps the guide and meters the oil lubricating the stem; on the DAZA, Audi lists it as 06L 109 675 D, 10 per engine, while the inlet side takes 057 109 675.
SUPERTECH exhaust valve stem seals
At the exhaust, the stem seal sits beside the valve exposed to the most heat. When it hardens or splits, oil is no longer held back: it slides down the stem and ends up burnt in the chamber, giving oil consumption, blue smoke and carbon on the valves as well as in the port. It still has to let a thin oil film pass, otherwise stem and guide wear.
SUPERTECH moulds its exhaust seals in Viton (FKM), a high-temperature elastomer picked for its long life against the heat given off by the exhaust valves: the brand says this material lets them cope with greater temperatures and rates it at 204 °C (400 °F) continuous. They sit on a guide with an 8.8 mm outside diameter, around a 6 mm stem. The set of 10 covers all exhaust valves of one head; inlet seals, moulded in polyacrylate (ACM), are sold apart.
Stem seal technical specifications
| Part number | Brand | Position | Material | Stem Ø | Guide Ø | Seal outside Ø |
|---|---|---|---|---|---|---|
| VS-VBM6E-10 | SUPERTECH | Exhaust | Viton (FKM) | 6 mm | 8.8 mm | 12.2 mm |
Stem seal installation
| Part | Original | Reinforced |
|---|---|---|
| Exhaust stem seal | 06L 109 675 D (DAZA) | Replaced by this set |
| Inlet stem seal | 057 109 675 (DAZA) | VS-VBM6I-10 |
| Valve guides | Inside Ø 6.0 mm | GDE-AU18T-20 |
| Valves | 6 mm stem | Inlet / Exhaust |
Technical guide
The brand offered
| Based in California's San Jose, SUPERTECH has made racing valvetrain parts for over 30 years: valves, springs, guides, stem seals. Each new part is first simulated by finite element analysis, then proven by known engine builders in drag racing, rallying and track use. |
Why two different materials?
Dimensionally, inlet and exhaust seals match; only heat sets them apart, as the exhaust valve runs far hotter. SUPERTECH thus keeps Viton (FKM), tougher, for the exhaust (VS-VBM6-E) and uses polyacrylate (ACM) on the inlet (VS-VBM6-I). A five-cylinder head needs 10 of each.
When valve stem seals must be replaced
- Blue smoke and oil consumption
- Head overhaul or valves taken out
- New valve guides fitted
- Uprated springs or valves installed
Vehicle compatibility
Audi
| Model | Engine code | Power | Years |
|---|---|---|---|
| RS3 Sportback (8P) | CEPA | 340 hp | 2011-2012 |
| RS3 (8V) | CZGB | 367 hp | 2015-2016 |
| RS3 (8V) | DAZA / DNWA | 400 hp | 2017-2020 |
| TT RS / TT RS Roadster (8J) | CEPA | 340 hp | 2009-2014 |
| TT RS / TT RS Roadster (8J) | CEPB | 360 hp | 2011-2014 |
| TT RS / TT RS Roadster (FV) | DAZA / DNWA | 400 hp | 2016- |
| RS Q3 (8U) | CTSA | 310 hp | 2013-2018 |
| RS Q3 performance (8U) | CZGB | 367 hp | 2015-2018 |
| RS Q3 / RS Q3 Sportback (F3) | DAZA / DNWA | 400 hp | 2019- |
Volkswagen
| Model | Engine code | Power | Years |
|---|---|---|---|
| Golf V 2.5 | BGP / BGQ | 152 hp | 2006-2008 |
| Golf V 2.5 | CBTA / CBUA | 170 hp | 2007-2008 |
| Golf V Variant 2.5 | BTK | 150 hp | 2007-2009 |
| Golf V Variant 2.5 | CCCA | 170 hp | 2008-2013 |
| Golf VI / Golf VI Variant 2.5 | CBTA / CBUA / CCCA | 170 hp | 2009-2014 |
| Jetta III 2.5 | BGP / BGQ / BTK | 150 hp | 2006-2010 |
| Jetta III 2.5 | CBTA / CBUA / CCCA | 170 hp | 2008-2010 |
| Jetta IV 2.5 | CBTA / CBUA / CCCA | 170 hp | 2010-2017 |
| New Beetle / New Beetle Cabriolet 2.5 | BPR / BPS | 150 hp | 2005-2010 |
| Beetle / Beetle Cabriolet 2.5 | CBTA / CBUA / CCCA | 170 hp | 2011-2019 |
| Passat 2.5 (A32) | CBTA / CBUA / CCCA | 170 hp | 2011-2020 |
KTM
| Model | Engine code | Power | Years |
|---|---|---|---|
| X-Bow GT-XR | DNWA | 500 hp | 2022- |
OEM part number (VAG exhaust stem seal): 06L 109 675 D (DAZA)
Remember the inlet valve stem seals
Swap the inlet seals together with the exhaust ones: they work in the same head. These SUPERTECH seals suit these engines:
| VAG 2.5 TFSI inlet stem seals → |
-
Brand
-
ReferenceVS-VBM6E-10
-
In stock2 Items