- In stock
SUPERTECH inlet valve stem seals VAG 2.5 TFSI 2.5 20V
Set of 10 inlet valve stem seals for VAG 2.5 TFSI and 2.5 20V five-cylinders, 6 mm stem.
- Brand: SUPERTECH
- Engines: CEPA, CEPB, CTSA, CZGB, DAZA, DNWA, BGP, BGQ, BPR, BPS, BTK, CBTA, CBUA, CCCA
- Material: Polyacrylate (ACM)
Audi, Volkswagen and KTM engines concerned
These seals fit the 6 mm stem inlet valves of VAG 20-valve five-cylinder engines: the 2.5 TFSI (CEPA, CEPB, CTSA, CZGB, DAZA, DNWA) powering the Audi RS3 8P and 8V, TT RS 8J and FV, RS Q3 8U and F3 as well as the KTM X-Bow GT-XR, and the naturally aspirated 2.5 20V (BGP, BGQ, BPR, BPS, BTK, CBTA, CBUA, CCCA) of the Volkswagen Golf V and VI, Jetta III and IV, New Beetle, Beetle and Passat (A32).
Each cylinder head carries 10 inlet valves, two per cylinder. The original seal covers the guide and wipes oil from the stem; for the DAZA, Audi lists it as 057 109 675, 10 per engine, the exhaust side taking 06L 109 675 D.
SUPERTECH inlet valve stem seals
A stem seal has to meter oil: it lets through only what the stem needs to stay lubricated in its guide, otherwise stem and guide wear. Worn or hardened by heat, it lets oil flow into the combustion chamber, causing oil consumption, blue smoke at cold start or after prolonged idling, and deposits on valves as well as spark plugs.
SUPERTECH moulds its inlet seals in a high quality rubber, a polyacrylate (ACM), intended for an 8.8 mm outside diameter guide around a 6 mm stem. The set of 10 fits every inlet valve of one head; the hotter exhaust takes seals in a high-temperature compound, sold apart.
Stem seal technical specifications
| Part number | Brand | Position | Material | Stem Ø | Guide Ø | Seal outside Ø |
|---|---|---|---|---|---|---|
| VS-VBM6I-10 | SUPERTECH | Inlet | Polyacrylate (ACM) | 6 mm | 8.8 mm | 12.2 mm |
Stem seal installation
| Part | Original | Reinforced |
|---|---|---|
| Inlet stem seal | 057 109 675 (DAZA) | Replaced by this set |
| Exhaust stem seal | 06L 109 675 D (DAZA) | VS-VBM6E-10 |
| Valve guides | Inside Ø 6.0 mm | GDE-AU18T-20 |
| Valves | 6 mm stem | Inlet / Exhaust |
Technical guide
The brand offered
| Founded in San Jose, Silicon Valley, SUPERTECH has drawn racing valvetrain components for over 30 years, from the valve to the stem seal. Its output is checked by ultrasound, X-ray and laser measurement, then refined alongside top-level engine builders. |
Inlet or exhaust?
Dimensions are shared by both seals, material is not: polyacrylate (ACM) VS-VBM6-I on the inlet, Viton (FKM) VS-VBM6-E on the exhaust, chosen for the greater heat the exhaust valves endure. SUPERTECH rates polyacrylate up to 177 °C (350 °F) and Viton at 204 °C (400 °F) continuous. These five-cylinder engines take 10 seals of each.
When valve stem seals must be replaced
- Oil burning, blue smoke when cold or after long idling
- Valves removed, head being rebuilt
- New valve guides installed
- Uprated springs or valves to be fitted
Vehicle compatibility
Audi
| Model | Engine code | Power | Years |
|---|---|---|---|
| RS3 Sportback (8P) | CEPA | 340 hp | 2011-2012 |
| RS3 (8V) | CZGB | 367 hp | 2015-2016 |
| RS3 (8V) | DAZA / DNWA | 400 hp | 2017-2020 |
| TT RS / TT RS Roadster (8J) | CEPA | 340 hp | 2009-2014 |
| TT RS / TT RS Roadster (8J) | CEPB | 360 hp | 2011-2014 |
| TT RS / TT RS Roadster (FV) | DAZA / DNWA | 400 hp | 2016- |
| RS Q3 (8U) | CTSA | 310 hp | 2013-2018 |
| RS Q3 performance (8U) | CZGB | 367 hp | 2015-2018 |
| RS Q3 / RS Q3 Sportback (F3) | DAZA / DNWA | 400 hp | 2019- |
Volkswagen
| Model | Engine code | Power | Years |
|---|---|---|---|
| Golf V 2.5 | BGP / BGQ | 152 hp | 2006-2008 |
| Golf V 2.5 | CBTA / CBUA | 170 hp | 2007-2008 |
| Golf V Variant 2.5 | BTK | 150 hp | 2007-2009 |
| Golf V Variant 2.5 | CCCA | 170 hp | 2008-2013 |
| Golf VI / Golf VI Variant 2.5 | CBTA / CBUA / CCCA | 170 hp | 2009-2014 |
| Jetta III 2.5 | BGP / BGQ / BTK | 150 hp | 2006-2010 |
| Jetta III 2.5 | CBTA / CBUA / CCCA | 170 hp | 2008-2010 |
| Jetta IV 2.5 | CBTA / CBUA / CCCA | 170 hp | 2010-2017 |
| New Beetle / New Beetle Cabriolet 2.5 | BPR / BPS | 150 hp | 2005-2010 |
| Beetle / Beetle Cabriolet 2.5 | CBTA / CBUA / CCCA | 170 hp | 2011-2019 |
| Passat 2.5 (A32) | CBTA / CBUA / CCCA | 170 hp | 2011-2020 |
KTM
| Model | Engine code | Power | Years |
|---|---|---|---|
| X-Bow GT-XR | DNWA | 500 hp | 2022- |
OEM part number (VAG inlet stem seal): 057 109 675 (DAZA)
Remember the exhaust valve stem seals
Exhaust seals are changed along with the inlet ones, in the same head. SUPERTECH offers these seals for these engines:
| VAG 2.5 TFSI exhaust stem seals → |
-
Brand
-
ReferenceVS-VBM6I-10
-
In stock2 Items