Skip to content
  • In stock
Coussinets de bielles trimetal ACL Races Series 4B1060H-001, Cote 001 Coussinets de bielles trimetal ACL Races Series 4B1060H-001, Cote 001

SUPERTECH inlet valve stem seals VAG VR6 2.8 12V AAA AMY AFP

€5.67 (tax incl.)
€7.09 (tax incl.) -20%

Set of 6 inlet valve stem seals for the Volkswagen and Ford 2.8 VR6 12V, 7 mm stem.

  • Brand: SUPERTECH
  • Engines: AAA, AMY, AFP
  • Material: Polyacrylate (ACM)
VS-VW7I-6
2 in stock in Europe (72h lead time)
Pay in installments

Volkswagen and Ford engines concerned

This set fits the inlet side of the 12-valve 2.8 VR6, an engine with 7 mm valve stems: the AAA of the Volkswagen Golf III, Vento, Corrado, Passat and Sharan and of the Ford Galaxy, the AMY of the Sharan and Galaxy, then the AFP of the Golf IV and Bora, from 1991 to 2005.

With two valves per cylinder, this six-cylinder has six inlet valves. Each carries an original seal that caps the guide and lets the right amount of oil reach the stem.

SUPERTECH inlet valve stem seals

On this engine as on any other, the stem seal acts as a metering device: it lets through the little oil that lubricates the stem in the guide and stops the rest, otherwise wear progresses. When the rubber hardens with age and heat, oil runs into the chamber and burns, bringing oil consumption, blue smoke at start-up or when pulling away after idling, and carbon on valves and plugs.

SUPERTECH inlet seals use a polyacrylate (ACM), a good quality rubber, and fit a guide of 9.8 mm outside diameter around a 7 mm stem. The set of 6 covers the inlet row; the hotter exhaust is handled with Viton seals sold apart.

Stem seal technical specifications

Part numberBrandPositionMaterialStem ØGuide ØSeal outside Ø
VS-VW7I-6 SUPERTECH Inlet Polyacrylate (ACM) 7 mm 9.8 mm 13.2 mm

Stem seal installation

PartOriginalReinforced
Inlet stem seal Replaced by this set
Exhaust stem seal VS-VW7E-6
Valves 7 mm stem Inlet / Exhaust

Technical guide

The brand offered

SUPERTECH SUPERTECH, founded in San Jose, California, has produced racing engine valvetrain components for more than 30 years, down to the stem seals. Each batch goes through ultrasound, X-ray and laser testing before being refined with seasoned engine builders.

Inlet or exhaust?

Inlet and exhaust use seals of identical dimensions in different materials: polyacrylate (ACM) VS-VW7-I on the inlet, Viton (FKM) VS-VW7-E on the exhaust, chosen to cope with exhaust-valve heat. According to SUPERTECH, the former withstands 177 °C (350 °F), the latter 204 °C (400 °F) continuous. The 12-valve VR6 needs 6 of each.

When valve stem seals must be replaced

  • Oil consumption, blue smoke at start-up or after long idling
  • Head stripped, valves out
  • New valve guides going in
  • Fitting uprated springs or valves

Vehicle compatibility

Volkswagen

ModelEngine codePowerYears
Golf III 2.8 VR6 (1H) AAA 163-174 hp 1992-1997
Vento 2.8 VR6 (1H) AAA 163-174 hp 1992-1998
Corrado 2.8 VR6 AAA 174 hp 1991-1995
Passat / Passat Variant 2.8 VR6 (B3/B4) AAA 174 hp 1991-1997
Sharan 2.8 VR6 / VR6 Syncro AAA / AMY 174 hp 1995-2000
Golf IV 2.8 VR6 (1J) AFP 177 hp 1999-2002
Golf IV Variant 2.8 V6 (1J) AFP 177 hp 2000-2004
Bora 2.8 VR6 (1J) AFP 177 hp 1998-2005
Jetta III 2.8 VR6 (1K) AAA 174 hp 2009-2010

Ford

ModelEngine codePowerYears
Galaxy 2.8 i V6 / V6 4x4 (WGR) AAA / AMY 174 hp 1995-2000
Important: this set does not suit the 24-valve VR6 (2.8 and 3.2), whose valves have a 6 mm stem.

Remember the exhaust valve stem seals

The exhaust side is overhauled together with the inlet, as both rows of seals age together. For this VR6, SUPERTECH offers:

VW VR6 2.8 12V exhaust stem seals →

16 other products in the same category

Viewed products

Loading...